USB interface (VP-D385(i) only)

Connecting to a PC

USB 接口 ( 仅限 VP-D385( i ))

连接到电脑

1.Connect a USB cable to the usb jack on the PC.

•If a USB cable is connected to the camcorder's USB jack, the Audio/Video

cable is disabled.

2. Connect the other end of the USB cable into the USB jack on the camcorder. (USB jack)

POWER

AV DV

MODE

CHG

VOL

1.连接 USB 数据线至电脑上的 USB 端口。

•如果将 USB 数据线连接到摄录机上的 USB 端口，则之前连接的音频 / 视频 电缆将不起作用。

2.将 USB 数据线的另一端插入摄录机上的USB 端口。

Disconnecting the USB Cable

•After completing the data transmission, you must disconnect the cable in the following way:

1.Click the "Unplug or eject hardware" icon on the task tray.

2.Select "USB Mass Storage Device" or "USB Disk," and then click "Stop."

3.Click "OK."4.Disconnect the USB cable from the miniDV camcorder and PC.

•If you disconnect the USB cable from the PC or the camcorder while transferring, the data transmission will stop and the data may be damaged.

•If you connect the USB cable to a PC via a USB HUB or simultaneously connect the USB cable along with other USB devices, the camcorder may not work properly. If this occurs, remove all USB devices from the PC and reconnect the camcorder.

Using the Removable Disk Function

•This function works in both M.Cam and M.Player modes. ➥page 18.

•You can easily transfer data from a memory card to a PC without additional cards via a USB connection.

1.Set the Select switch to Card.

2. Press the MODE button to set Camera (

) or Player (

).

3.Connect one end of the USB cable to the USB jack on the camcorder and the other end to the USB jack on your computer.

4.To verify whether the removable disk has been properly recognised, open Windows Explorer and locate the removable disk.

•You can copy the movie and photo images to your PC and play them back.98_ English

断开 USB 数据线连接

•完成数据传输后，您不需按照如下步骤断开连接：1. 点击任务栏上 " 安全删除硬件 " 图标。2. 选择 "USB Mass Storage Device" 或"USB Disk," 然后点击 " 停止 "。3. 点击 " 确定 "。4. 断开摄录机与电脑的连接。•如果在转移数据的过程中从数码摄像机或者电脑上断开 USB 数据线，数据传输将会停止并且数据可能损坏。

•如果您通过 USB HUB 将 USB 数据线与电脑相连或者同时 连接其他的 USB 设备，数码摄像机可能会工作不正常。如 果发生这种情况，请您从电脑上拔下 USB 设备，重新连接 数码摄像机。

使用可移动磁盘功能

•此功能仅支持在 M.Cam( 存储卡摄像 ) 和 M.Player( 存储卡播放 ) 模 式下使用。➥ 第 18 页

•通过 USB 连接，您可以在不使用外接卡的情况下，将存储卡内的数 据轻松地传输到电脑中。

1.切换存储介质为 Card.。2.按下 MODE 按钮设置为 Camera( 摄像 ) 模式 () 或 Player( 播放 )模式 ( )。3.将 USB 数据线的一卷连接至摄录机的 USB 端口，然后将另一端插 入电脑的 USB 端口。4.为了确认移动磁盘是否被正确地识别，请打开 Windows Explorer 查看是否有可移动磁盘。• 您可以复制影音文件和照片文件至电脑中并且播放它们。中文 _98