initial setting : system menu setting
SETTING THE CLOCK (CLOCK SET)
•Clock setup works in Camera / Player / M.Cam / M.Player modes. ➥page 18•Set the date and time when using this camcorder for the first time.1.Set the Select switch to CARD or TAPE. (VP-D385( i ) only)2. Press the MODE button to set Camera ( | ) or | |
Player ( | ). |
|
4.Move the Joystick (▲ / ▼) up or down to select "System", then press the Joystick or move the Joystick () to the right.
5.Move the Joystick (▲ / ▼) up or down to select "Clock Set", then press the Joystick.
•The year will be highlighted first.6.Move the Joystick (▲ / ▼) up or down to set the current year, then press the Joystick.
•The month will be highlighted.7.You can set the month, day, hour and minute following the same procedure after setting the year.
8.Press the Joystick after setting the minutes.•A message "Complete !" is displayed.9.To exit, press the MENU button.•You can set the year up to 2037.•Turning the date and time display on/off To switch the date and time display on or off, access the menu and change the date/ time display mode. ➥page 32
Display illustrations in this manual-OSD illustrations of VP-D385( i ) are used in this manual.-Some of the OSD items shown in this manual may differ slightly from the actual items on your camcorder.
CARD TAPE
(VP-D385( i ) only)
Camera Mode
System
Clock Set
Remote
Beep Sound
Shutter Sound
Language
Demonstration
Adjust Select
Camera Mode
System
Clock Set
Remote
Beep Sound
Shutter Sound
Language
Demonstration
Move Select
初始设置:系统菜单设置
设置时钟 (CLOCK SET( 时钟设置 ))
| • | 设置用于 Camera( 摄像 ) 模式 /Player( 播放 ) 模式 / | ||
|
| M.Cam( 存储卡摄像 ) 模式 /M.Player( 存储卡播放 ) | ||
MODE | • | 模式下的时钟。➥ 第 18 页 |
| |
| 当第一次使用本摄录机时,请设置时钟。 |
| ||
| 1. | 切换存储介质为 CARD 或 TAPE。( 仅限 VP-D385( i )) | ||
| 2. | 按下 MODE 按钮设置为 Camera( 摄像 ) 模式 ( | ) 或 | |
BATT. |
| Player( 播放 ) 模式 ( | )。 |
|
| 3. | 按下 MENU 按钮。 |
|
|
|
| • 屏幕上显示菜单列表。 |
| |
| 4. | 向上或向下拨动操纵杆(▲ / ▼)选择"System(系统)", | ||
|
| 然后按下操纵杆或者向右拨动操纵杆 () 确认选择。 | ||
| 5. | 向上或向下拨动操纵杆 (▲ / ▼) 选择 |
| |
|
| "Clock Set( 时钟设置 )",然后按下操纵杆确认。 |
| |
|
| • 年份设置选项首先被高亮显示。 |
| |
BATT. | 6. | 向上或向下拨动操纵杆 (▲ / ▼) 选择当前年份,然后按 | ||
|
| 下操纵杆确认。 |
|
|
| 7. | • 然后,月份设置被高亮显示。 |
| |
| 设置当前年份后,按照相同的步骤设置月,日,小时和 | |||
|
| 分钟。 |
|
|
1 JAN 2008 | 8. | 设置分钟后按下操纵杆。 |
| |
00 : 00 |
| |||
| • 屏幕上显示提示信息 "Complete !( 完成! )"。 | |||
|
| |||
| 9. | 若要退出菜单,按下 MENU 按钮。 |
|
MENU Exit | • |
| 2037 |
| 您可以将年份设置到 | 。 |
•打开 / 关闭日期和时间显示。
切换日期和时间显示状态为打开或关闭,通过菜单 更改日期 / 时间显示模式。➥ 第 32 页
1 JAN 2008 | 本说明书内的屏幕显示介绍 | ||
00 : 00 | |||
- | 本说明书内举例的 OSD(屏幕显示)是基于 | ||
Complete ! | |||
|
| ||
MENU Exit | - | 根据您摄录机的实际情况,OSD(屏幕显示)项目可 | |
| 能会有所不同。 | ||
|
|