Timing Belt Replacement | SATO M84PRO specification

Section 7: Replacement Procedures

11Insert the short spindle of drive roller (1) into housing frame so that it rests on the far side of the label ramp secure using clamp (4) and two screws (3).

12Insert clamp (8) onto the left end of drive roller (1) and secure to the frame using screw (7).

13Insert pulley (6) onto the left end of drive roller (1) and apply inner belt (not shown).

14Apply outer belt (not shown) to pulley (6) and e-clip (5) to left roller spindle.

15Adjust belt tension in accordance with its relative procedure in the Adjustment Procedures section of this manual.

16Reconnect power supply cord, test cycle, and reattach/close all covers.

NOTE: Figures 10-1, 10-2, and 10-3 of the Daigrams & Schematics section provides guidance on housing cover, media, and ribbon installation.

TIMING BELT REPLACEMENT

The M84pro Printer utilizes four timing belts coupled with dual action toothed pulleys to provide drive distribution throughout the assembly. Two belts are configured to transfer torque from the motor to the label feed roller. A third belt transfers torque from the feed roller to the platen roller. And the fourth transfers torque from the platen roller to the ribbon rewind spindle. All four operating in conjunction provide the total drive configuration for the primary machine.

The optional cutter assembly has its own drive mechanism that operates when directed by the printer, but independently of the printer drive assembly. The cutter drive assembly also comprises drive belts and pulleys. Those will not be addressed in this procedure.

1Switch off the printer and disconnect the power supply cord.

2 Open/remove the top, right, and left housing covers.

NOTE: Figure 10-1 of the Daigrams & Schematics section provides guidance on housing cover removal.

3Disconnect all wiring harnesses that pose an obstruction to belt removal.

4Remove two screws (1, Figure 7-12a) securing pulley bracket (2) to the printer frame.

5Withdraw bracket (2) along with belts (3) and (4) from motor spindle (5) and feed roller pul- ley (6) respectively.

M84Pro Service Manual

PN 9001111A

Page 7-14

Image 82

SATO M84PRO service manual Timing Belt Replacement

Contents

M84PRO Page Table of Contents Factory Resets Replacement ProceduresAdjustment Procedures Diagrams & Schematics Introduction Result in Presonal Injury General Description Theory of Operation Primary Components Switches and Indicators Connection Ports Switches, Indicators, and Connection Ports Environmental Physical CharacteristicsPower Print Sensing MediaRibbon Interface Modules Character Font Capabilities BAR Code Capabilties Regulatory Approvals Interface Types Receive Buffer Interface Specifications Specifications IEEE1284 Parallel Interface Direction Signal Definition RS232C Serial Interface SignalsRS232 Serial Interface Host Interconnection Cable Requirements DB9Printer BI-DIRECTIONAL Communications Universal Serial BUS USB AdapterLocal Area Network LAN Interface ENQUIRE/ACK/NAK Cancel can Stream Identification Print Stop DLE Accessories Installation Label Cutter Installation Slide entire print mechanism fully toward the rear 1b, Label Cutter Installation Dispenser Installation 1c, Label Cutter Installation 2a, Dispenser Installation 2b, Dispenser Installation Flash Memory Installation 2c, Dispenser Installation Pcmcia Memory Expansion Installation Flash Card Installation 4a, Memory Expansion REAL-TIME Clock Installation Enter all of the date data required for calender operation Interface Module Upgrade RS232 TRANSMIT/RECEIVE Setting DIP Switch PanelsOFF DSW1-4 Printer SET UP DSW2 OFF DSW2-5 DSW3 DSW3 OFF Setting Default Settings Default SettingsSoftware Default Settings Software Default Settings Potentiometer Adjustments Default Completed LCD Panel Printer Configuration Configuration Modes Normal Mode Advanced Mode LCD Display Definition Print Offset Zero SlashAuto Online SET Calendar Card Mode Card Memory Xxxxxxx ErrorMEM Select CC1 Copy Start MEMORY-CARDCOPY CARD-MEMORYCopy Copying ALL Card Format Memory Format GAP XXV Service ModeService Mode Input Setting the threshold is Auto Online Feed Feed on ErrorEYE XXV Reprint W/FEED Enable Disable Priority SettingCommand LCD EXT PIN 9 Select Counters Mode Test Print Mode Default Settings Mode MAINTENANCE/FACTORY Mode ALL Clear Mode Clear NON-STANDARD Protocol Download User Defined Protocol Codes HEX Dump Mode QTY000000 Error Signals LED LCD Message Beep Error Condition To Clear Ribbon Wrinkling Troubleshooting TableImage Voids Light Print Images No Ribbon Movement Power LED not IlluminatedSmeared Print Images No Label Movement Label LED is Illuminated Troubleshooting ProceduresError LED Illuminated Ribbon LED Illuminated Universal Serial BUS USB Interface LAN Ethernet Interface TP Test Module Usage Dial Application Description TP Test Module Usage Ribbon Sensor Operation Verification Troubleshooting PN 9001111A Replacement Procedures Main Circuit Board Replacement Replacement Procedures Interface Board Replacement Interface Board Replacement Daughter Board Replacement Daughter Board Replacement Memory Card Replacement Power Board Replacement Panel Board Replacement Power Board Replacement LCD Board Replacement Panel Board Replacement Fuse Replacement LCD Board Replacement Motor Replacement Fuse Replacement Motor Replacement Platen Roller Replacement Feed Roller Replacement 10, Platen Roller Replacement 11, Feed Roller Replacement Timing Belt Replacement 12a, Motor and Feed Belt Replacement 12c, Platen Roller Belt Replacement 12d, Ribbon and Rewind Belt Replacement Print Head Replacement 13, Wiring Harness Connection 14, Print Head Replacement LABEL-OUT Sensor Switch Replacement 15, Label-Out Sensor Switch Replacement 16, Wiring Harness Connection Label Position Sensor Replacement 17, Label Position Sensor Replacement Ribbon Sensor Replacement 18, Wiring Harness Connection 21, Ribbon Sensor Replacement Cutter Belt Replacement 23a, Cutter Belt Replacement Cutter Circuit Board Replacement 24, Cutter Circuit Board Replacement Replacement Procedures Adjustment Procedures Print Defects Relative Procedure Print Head Position Alignment Print Head Balance Adjustment Adjustment Procedures Ribbon Guide Plate Adjustment EDI Feed Roller Adjustment Media Feed Roller Adjustment Timing Belt Adjustment Tightening Timing Belts Pitch Sensor Setup for Notch Tags Pitch Sensor Assembly Print Position Adjustment Label Stock Diagram Label GAP Sensor Adjustment Label Sensor Adjustment EYE-MARK Sensor Adjustment Offset Label Stop Position Adjustment LCD Display Adjustment Print Darkness Adjustment Adjustment Procedures PN 9001111A Factory Resets Factory Settings / Test Print Clear Head Counters Press the Feed key to clear the head counter Clear Dispenser Counter Press the Feed key to clear the dispenser counter Clear Cutter Counter Press the Feed key to clear the cutter counter Clear Eeprom Diagrams & Schematics Housing Cover Removal & Installation Media Loading Ribbon Loading Paper Specifications Pa per Feedin g Direction Accessories & Sensors Location Paper Feed Direction Print Position Reference Diagram Paper Feed Direction CONTINUOUS, Pitch Sensor Enabled Head Check Disabled Print Operation Sequence CONTINUOUS, Pitch Sensor Disabled Head Check Disabled CONTINUOUS, Pitch Sensor Disabled Head Check Enabled Msec passes 11, Operation Sequence Chart 12, Operation Sequence Chart 13, Operation Sequence Chart 14, Operation Sequence Chart 15, Operation Sequence Chart 16, Operation Sequence Chart 17, Operation Sequence Chart 18, Operation Sequence Chart 19, Operation Sequence Chart