Manuals / SMC Networks / Computer Equipment / Switch

SMC Networks SMC6824M manual 187, Vlan Static List Creating VLANs

Models: SMC6824M

1 608

Download 608 pages 58 Kb

Page 243

Image 243

VLAN CONFIGURATION

•VLAN ID – ID of configured VLAN (1-4093, no leading zeroes).

•VLAN Name – Name of the VLAN (1 to 32 characters).

•Status (Web) – Enables or disables the specified VLAN.

-Enable: VLAN is operational.

-Disable: VLAN is suspended; i.e., does not pass packets.

•State (CLI) – Enables or disables the specified VLAN.

-Active: VLAN is operational.

-Suspend: VLAN is suspended; i.e., does not pass packets.

•Add – Adds a new VLAN group to the current list.

•Remove – Removes a VLAN group from the current list. If any port is assigned to this group as untagged, it will be reassigned to VLAN group 1 as untagged.

Web – Click VLAN, 802.1Q VLAN, Static List. To create a new VLAN, enter the VLAN ID and VLAN name, mark the Enable checkbox to activate the VLAN, and then click Add.

Figure 3-79 VLAN Static List - Creating VLANs

3-187

Page 243

Image 243

SMC Networks SMC6824M manual 187, Vlan Static List Creating VLANs

Contents

TigerStack III 10/100 Page TigerStack III 10/100 Management Guide Trademarks Limited Warranty Limited Warranty Table of Contents Table of Contents Table of Contents Table of Contents Vii Command Line InterfaceViii Table of Contents Table of Contents Table of Contents Xii Xiii Xiv Table of Contents Xvi Xvii Glossary IndexXviii Xix TablesTables Xxi Xxii Xxiii Figures37 802.1X Global Information XxivXxv Xxvi Key Features Key FeaturesFeature Description Lacp Description of Software FeaturesDescription of Software Features Introduction Description of Software Features Introduction System Defaults System DefaultsFunction Parameter Default Https Pvid Dhcp Configuration Options Connecting to the SwitchInitial Configuration Required Connections Remote Connections Recovering from Stack Failure or Topology Change Stack OperationsSelecting the Stack Master Basic Configuration Resilient IP Interface for Management AccessConsole Connection Setting an IP Address Setting PasswordsManual Configuration Dynamic Configuration Enabling Snmp Management Access Community Strings for Snmp version 1 and 2c clients Clients, we recommend that you delete both of the defaultTrap Receivers Configuring Access for Snmp Version 3 ClientsSaving Configuration Settings Managing System Files Configuring Power over Ethernet Initial Configuration Using the Web Interface Configuring the SwitchConfiguring the Switch Home Navigating the Web Browser InterfaceWeb Page Configuration Buttons ButtonAction Panel Display Front Panel IndicatorsSwitch Main Menu Main MenuMenu Description Sntp ACL Vlan Mstp 206 Vlan ID Field Attributes Displaying System InformationSystem Information CLI Specify the hostname, location and contact information Displaying Switch Hardware/Software VersionsManagement Software General Switch Information Web Click System, Switch InformationField Attributes Displaying Bridge Extension CapabilitiesSetting the IP Address CLI Enter the following commandWeb Click System, Bridge Extension Command Attributes IP Interface Configuration Manual Manual ConfigurationIP Interface Configuration Dhcp Using DHCP/BOOTPManaging Firmware Command AttributesCopy Firmware Downloading System Software from a ServerSetting the Startup Code Command Usage Saving or Restoring Configuration SettingsBasic Configuration 11 Downloading Configuration Settings for Start-Up Downloading Configuration Settings from a Server12 Setting the Startup Configuration Settings Command Attributes Console Port SettingsCLI only 13 Console Port Settings Command Attributes Telnet Settings14 Configuring the Telnet Interface System Log Configuration Configuring Event LoggingLogging Levels Command Attributes15 System Logs Remote Log Configuration16 Remote Logs 17 Displaying Logs Displaying Log MessagesCLI This example shows the event message stored in RAM Sending Simple Mail Transfer Protocol Alerts18 Enabling and Configuring Smtp Alerts 19 Resetting the Switch Resetting the SystemSetting the System Clock Configuring SntpCLI Use the reload command to reboot the system 20 Sntp Configuration Setting the Time ZoneSimple Network Management Protocol 21 Setting the Time ZoneConfiguring the Switch Model Level Group Read Write Notify Security View SNMPv3 Security Models and LevelsSetting Community Access Strings CLI The following example enables Snmp on the switchEnabling the Snmp Agent 23 Configuring Snmp Community Strings Specifying Trap Managers and Trap Types Command UsageCommand Attributes 24 Configuring Snmp Trap Managers Setting the Local Engine ID Configuring SNMPv3 Management AccessCLI This example sets an SNMPv3 engine ID Specifying a Remote Engine IDCLI This example specifies a remote SNMPv3 engine ID Configuring SNMPv3 UsersConfiguring the Switch 27 Configuring SNMPv3 Users 169 Configuring Remote SNMPv3 UsersCommand Attributes 28 Configuring Remote SNMPv3 Users Configuring SNMPv3 Groups Object Label Object ID Description Supported Notification MessagesObject Label Object ID Description Rmon Events SwIpFilterRejectTrap 29 Configuring SNMPv3 Groups 165 Setting SNMPv3 Views30 Configuring SNMPv3 Views 163 User AuthenticationCommand Attributes Configuring User Accounts31 Configuring User Accounts Configuring Local/Remote Logon Authentication That use software runningOn a central server to Radius Settings Command Attributes32 Authentication Server Settings Tacacs Settings104 Configuring HttpsWeb Browser Operating System Https Support33 Https Settings Replacing the Default Secure-site CertificateConfiguring the Secure Shell Command Usage Configuring the Switch Field Attributes Generating the Host Key Pair34 SSH Host-Key Settings SSH server includes basic settings for authentication Configuring the SSH Server35 SSH Server Settings Command Usage Configuring Port SecurityCommand Attributes 36 Enabling Port Security Configuring 802.1X Port Authentication Web Click Security, 802.1X, Information Displaying 802.1X Global Settings802.1X protocol provides client authentication 802.1X System Authentication Control The global setting forConfiguring 802.1X Global Settings CLI This example shows the default global setting forCLI This example enables 802.1X globally for the switch Configuring Port Settings for Authorized 39 802.1X Port ConfigurationUser Authentication Displaying 802.1X Statistics 802.1X StatisticsParameter Description CLI This example displays the 802.1X statistics for port 40 Displaying 802.1X StatisticsCommand Usage Filtering IP Addresses for Management Access41 Entering IP Addresses to be Filtered Configuring Access Control Lists Access Control ListsCommand Attributes Setting the ACL Name and TypeConfiguring a Standard IP ACL Command Attributes 100CLI This example creates a standard IP ACL named bill 101 Configuring an Extended IP ACL Command Attributes102 103 44 Configuring Extended IP ACLs104 Configuring a MAC ACL Command Attributes105 Command Usage106 45 Configuring MAC ACLsConfiguring ACL Masks 107Specifying the Mask Type Configuring an IP ACL Mask 108This mask defines the fields to check in the IP header 109 47 Configuring an IP based ACLConfiguring a MAC ACL Mask 110This mask defines the fields to check in the packet header 111 48 Configuring an ACL MAC Mask112 Binding a Port to an Access Control List49 Mapping ACLs to Port Ingress/Egress Queues 113114 Port ConfigurationCommand Attributes Web Displaying Connection Status115 Field Attributes CLIWeb Click Port, Port Information or Trunk Information Current status 116Configuring Interface Connections 117CLI This example shows the connection status for Port 118 119 51 Configuring Port Attributes120 Creating Trunk Groups121 Statically Configuring a Trunk Command Usage122 52 Static Trunk Configuration123 Enabling Lacp on Selected Ports Command Usage124 53 Lacp Port Configuration125 126 127 54 Lacp Aggregation Port Configuration128 Lacp Port Counters 129Displaying Lacp Port Counters You can display statistics for Lacp protocol messagesDisplaying Lacp Settings and Status for the Local Side Lacp Internal Configuration Information130 131 56 Displaying Lacp Port Information 132Displaying Lacp Settings and Status for the Remote Side 10 Lacp Neighbor Configuration Information133 57 Displaying Remote Lacp Port Information 134135 Setting Broadcast Storm Thresholds136 Configuring Port Mirroring137 59 Configuring a Mirror PortConfiguring Rate Limits Command Attribute138 139 Showing Port Statistics11 Port Statistics 140141 Rmon Statistics 142143 61 Port Statistics 144Power Over Ethernet Settings 145CLI This example shows statistics for port Switch Power Status Displays the Power over Ethernet parameters for the switch146 Setting a Switch Power Budget Web Click PoE, Power Status147 148 Displaying Port Power StatusConfiguring Port PoE Power Web Click PoE, Power Port Status149 150 65 Configuring Port PoE PowerAddress Table Settings Setting Static Addresses151 152 Displaying the Address Table67 Displaying the MAC Dynamic Address Table 153CLI This example sets the aging time to 300 seconds Spanning Tree Algorithm ConfigurationChanging the Aging Time 154155 156 Displaying Global Settings157 158 Web Click Spanning Tree, STA Information 159Configuring Global Settings Global settings apply to the entire switch160 161 Basic Configuration of Global Settings162 Root Device Configuration163 Configuration Settings for Rstp164 70 Configuring the Spanning Tree Algorithm165 Displaying Interface Settings166 AD B 16771 STA Port Information 168169 Configuring Interface Settings170 171 72 Configuring Spanning Tree Algorithm per PortConfiguring Multiple Spanning Trees 172CLI This example sets STA attributes for port 173 73 Mstp Vlan Configuration174 175 Displaying Interface Settings for Mstp176 177 Configuring Interface Settings for MstpCLI This example sets the Mstp attributes for port 178Vlan Configuration Ieee 802.1Q VLANs179 Assigning Ports to VLANs 180181 Forwarding Tagged/Untagged Frames 182Enabling or Disabling Gvrp Global Setting CLI This example enables Gvrp for the switch183 184 Displaying Basic Vlan InformationWeb Click VLAN, 802.1Q VLAN, Basic Information Displaying Current VLANs 185Command Attributes CLI 186Creating VLANs 79 Vlan Static List Creating VLANs 187188 Adding Static Members to VLANs Vlan IndexCLI This example creates a new Vlan 189 Command AttributesAdding Static Members to VLANs Port Index 190191 Configuring Vlan Behavior for Interfaces192 193 194 Private VLANsVlan ID ID of configured Vlan 195Displaying Current Private VLANs 83 Displaying Private Vlan Port Information 196197 Configuring Private VLANs198 Associating Community VLANsEach community Vlan must be associated with a primary Vlan Displaying Private Vlan Interface Information 199200 Configuring Private Vlan Interfaces201 87 Configuring Private Vlan Ports202 Class of Service ConfigurationLayer 2 Queue Settings Setting the Default Priority for Interfaces203 CLI This example assigns a default priority of 5 to port13 CoS Priority Levels 204Mapping CoS Values to Egress Queues 12 Mapping CoS Values to Egress Queues205 89 Configuring Traffic Classes206 Selecting the Queue Mode207 Setting the Service Weight for Traffic ClassesSelecting IP Precedence/DSCP Priority Layer 3/4 Priority Settings208 Mapping Layer 3/4 Priorities to CoS Values209 Mapping IP Precedence14 Mapping IP Precedence 210 93 Mapping IP Precedence to Class of Service ValuesIP Dscp Value CoS Value 211Mapping Dscp Priority 15 Mapping Dscp Priority212 94 Mapping IP Dscp Priority to Class of Service ValuesMapping IP Port Priority 21395 Globally Enabling the IP Port Priority Status 214215 Copy Settings16 CoS to ACL Mapping CLI This feature not supported through the CLI216 Mapping CoS Values to ACLs98 Mapping CoS Values to ACLs 217Changing Priorities Based on ACL Rules 21899 Changing Priorities Based on ACL Rules 219Multicast Filtering Igmp Protocol220 221 Layer 2 Igmp Snooping and Query222 Configuring Igmp Snooping and Query Parameters223 100 Configuring Internet Group Management ProtocolDisplaying Interfaces Attached to a Multicast Router 224Specifying Interfaces Attached to a Multicast Router 225226 Displaying Port Members of Multicast Services227 103 Displaying Port Members of Multicast Services228 Assigning Ports to Multicast ServicesConfiguring Domain Name Service Configuring General DNS Server Parameters229 230 231 105 Configuring DNS232 Configuring Static DNS Host to Address Entries106 Mapping IP Addresses to a Host Name 233234 Displaying the DNS CacheWeb Select DNS, Cache 235236 Using the Command Line Interface Accessing the CLIConsole Connection Telnet Connection Entering Commands This section describes how to enter CLI commandsKeywords and Arguments Minimum Abbreviation Command CompletionGetting Help on Commands Showing CommandsCommand Line Interface Partial Keyword Lookup Negating the Effect of CommandsUsing Command History Understanding Command ModesExec Commands Command ModesClass Mode Configuration Commands Mode Command Prompt Configuration Command ModesCommand Line Processing Keystroke CommandsKeystroke Function Command Groups Command Group IndexCommand Group Description Configures DNS services 286 Password-thresh command Line CommandsLine Commands Command Function ModeLine Line Configuration LoginSyntax Login local no login Login localNo password is specified PasswordUsername 4-34password Syntax Password 0 7 password no passwordTo set the timeout to two minutes, enter this command Timeout login responseLogin 4-15password-thresh CLI Disabled 0 seconds Telnet 300 secondsExec-timeout Syntax Exec-timeout seconds no exec-timeoutCLI and Telnet 600 seconds 10 minutes Password-thresh Syntax Password-thresh threshold no password-threshDefault value is three attempts Syntax Databits 7 8 no databits Silent-timeDatabits Syntax Silent-time seconds no silent-timeSyntax Parity none even odd no parity ParitySyntax Speed bps no speed To specify no parity, enter this commandTo specify 57600 bps, enter this command SpeedSyntax disconnect session-id StopbitsDisconnect Stopbits 1Syntax Show line console vty Show lineSyntax enable level General CommandsEnable General CommandsDisable Disable Enable passwordNone Show history ConfigureThis command restarts the system This command resets the entire systemReload Exit This example shows how to reset the switchThis command returns to Privileged Exec mode EndUse this command to exit the configuration program This example shows how to quit a CLI sessionQuit System Management Commands System Management CommandsCommand Group Function Syntax Prompt string no prompt Device Designation CommandsDevice Designation Commands PromptSyntax Light unit unit HostnameLight unit Syntax Hostname name no hostnameUser Access Commands User Access CommandsUsername Username Access-level Password 10 Default Login SettingsDefault is level is level Default password is super Enable passwordManagement IP Filter CommandsEnable 4-25authentication enable 11 IP Filter CommandsShow management 12 Web Server Commands Web Server CommandsIp http server Default Setting Command ModeSyntax No ip http server Default Setting Ip http portIp http secure-server Syntax No ip http secure-server Default SettingPortnumber The UDP port used for HTTPS. Range Ip http secure-port13 Https System Support Ip http secure-port4-42 Copy tftp https-certificateIp http secure-server4-41 Telnet Server Commands14 Telnet Server Commands Ip telnet serverServer Enabled Server Port Secure Shell CommandsCommand Function Mode 15 Secure Shell CommandsSystem Management Commands Syntax No ip ssh server Default Setting DisabledIp ssh server Seconds Ip ssh timeoutSyntax Ip ssh timeout seconds no ip ssh timeout Ip ssh crypto host-key generate 4-51 show sshExec-timeout4-18 show ip ssh Ip ssh authentication-retriesIp ssh server-key size Delete public-keySyntax Delete public-key username dsa rsa Generates both the DSA and RSA key pairs Ip ssh crypto host-key generateSyntax Ip ssh crypto host-key generate dsa rsa Dsa DSA Version 2 key type Rsa RSA Version 1 key typeSyntax Ip ssh save host-key dsa rsa Ip ssh crypto zeroizeIp ssh save host-key Syntax Ip ssh crypto zeroize dsa rsaSaves both the DSA and RSA key This command displays the current SSH server connectionsShow ip ssh Show sshTerminology 16 show ssh display descriptionShows all public keys Show public-keySyntax Show public-key user username host Username Name of an SSH user. Range 1-8 characters17 Event Logging Commands Event Logging CommandsLogging history 4-57clear logging Syntax No logging on Default SettingLogging on Logging historyFlash errors level 3 RAM informational level 6 18 Logging LevelsLevel Severity Name Description Hostipaddress The IP address of a syslog server Logging hostLogging facility Syntax No logging host hostipaddressDisabled Level 7 Logging trapSyntax Logging trap level no logging trap Syntax Show logging flash ram sendmail trap Clear logShow logging Syntax Clear log flash ram19 show logging flash/ram display description Following example displays settings for the trap functionShow log 20 show logging trap display descriptionSyntax Show log flash ram Following example shows the event message stored in RAM Smtp Alert Commands21 Smtp Commands Logging sendmail hostSyntax Logging sendmail level level Logging sendmail levelSyntax Logging sendmail source-email email-address Logging sendmail source-emailSyntax No logging sendmail destination-email email-address Syntax No logging sendmail Default SettingLogging sendmail destination-email Logging sendmailTime Commands 22 Time CommandsShow logging sendmail Sntp client Syntax No sntp client Default SettingSntp server Sntp server 4-70 sntp poll 4-71 show sntpSyntax Sntp server ip1 ip2 ip3 Sntp poll Sntp client 4-69 sntp poll 4-71 show sntpSyntax Sntp poll seconds no sntp poll Sntp client Show sntpNone Clock timezoneSyntax This command displays the system clockCalendar set Show calendarSystem Status Commands Show startup-config23 System Status Commands Example Related Commands Show running-configShow startup-config Show system This command displays system informationShow version Show users24 Flash/File Commands Flash/File CommandsPrivileged Exec CopyCommand Usage Following example shows how to download a configuration file Command Line Interface This command deletes a file or image DeleteDir Delete public-key 25 File Directory Information This command displays a list of files in flash memorySyntax Dir unit boot-rom config opcode filename DirFollowing example shows how to display all file information WhichbootBoot system Syntax Boot system unit boot-romconfig opcode filenameDir 4-87whichboot Power over Ethernet Commands 26 PoE CommandsCommand Group Function Mode Syntax No power inline compatible Power mainpower maximum allocationPower inline compatible Syntax Power mainpower maximum allocation watts unit unitCompatible Mode Enabled Power inline Power inline maximum allocationSyntax No power inline Default Setting Low Power inline priorityUnit Stack unit. Range Port Port number. Range Show power inline statusSyntax Show power inline status interface EthernetMainpower maximum allocation on Show power mainpower27 show power inline status parameters 28 show power mainpower parameters30 Authentication Sequence Command Authentication CommandsAuthentication Sequence 29 Authentication CommandsLocal Authentication loginUsername for setting the local user names and passwords Authentication enableRadius Client 31 Radius Client CommandsRadius-server host Default Setting Auth-portTimeout 5 seconds Retransmit Command Mode1812 Radius-server portRadius-server key Syntax Radius-server port portnumber no radius-server portRadius-server retransmit Radius-server timeoutPrivileged Exec Show radius-serverHostipaddress IP address of a TACACS+ server 32 TACACS+ Client CommandsTACACS+ Client Tacacs-server hostSyntax Tacacs-server key keystring no tacacs-server key Tacacs-server portTacacs-server key Syntax Tacacs-server port portnumber no tacacs-server portShow tacacs-server Port Security CommandsPort security 33 Port Security CommandsStatus Disabled Action None Maximum Addresses Interface Configuration Ethernet109 34 802.1X Port Authentication Commands 802.1X Port AuthenticationDot1x max-req Dot1x defaultSyntax No dot1x system-auth-control Default Setting Dot1x system-auth-controlForce-authorized Default Command ModeDefault Dot1x port-controlSingle-host Dot1x operation-modeSyntax No dot1x re-authentication Command Mode Dot1x re-authenticateDot1x re-authentication Syntax Dot1x re-authenticate interfaceDot1x timeout quiet-period Dot1x timeout re-authperiodSeconds The number of seconds. Range Statistics Displays dot1x status for each port Interface Dot1x timeout tx-periodShow dot1x Syntax Show dot1x statistics interface interface117 State- Current state including initialize, reauthenticate Authenticator State MachineAccess Control Lists Access Control List CommandsAccess Control List Commands Masks for Access Control Lists 35 Access Control List CommandsCommand Groups Function IP ACLs 36 IP ACL CommandsSyntax No access-list ip standard extended aclname Access-list ipPermit, deny Standard ACL Access-list ip extended fragment-auto-maskStandard ACL Permit, deny Extended ACLExtended ACL No permit deny tcp127 Permit, deny Ip access-group4-134 Show ip access-listThis command displays the rules for configured IP ACLs Syntax Show ip access-list standard extended aclnameAccess-list ip mask-precedence Syntax No access-list ip mask-precedence in outMask IP ACL 4-130 ip access-group4-134 IP Mask Syntax No mask protocol131 132 Syntax Show access-list ip mask-precedence in out Show access-list ip mask-precedenceSyntax No ip access-group aclname in out Ip access-groupThis command shows the ports assigned to IP ACLs Show ip access-groupMap access-list ip Show ip access-list4-12837 Egress Queue Priority Mapping Show map access-list ipQueue cos-map4-257 Show map access-list ip Syntax Show map access-list ip interfaceMap access-list ip Match access-list ipMAC ACLs Match access-list ip38 MAC ACL Commands Show markingSyntax No access-list mac aclname Access-list macSyntax No permit deny Permit, deny MAC ACLMAC ACL Permit, deny Mac access-group4-146 Show mac access-listThis command displays the rules for configured MAC ACLs Syntax Show mac access-list aclnameMask MAC ACL 4-144 mac access-group4-146 Access-list mac mask-precedenceMAC Mask Syntax No mask pktformatThis example creates an Egress MAC ACL 145Syntax Mac access-group aclname in out Show access-list mac mask-precedenceMac access-group Syntax Show access-list mac mask-precedence in outThis command shows the ports assigned to MAC ACLs Show mac access-groupMap access-list mac Show mac access-list4-14239 Mapping CoS Values to MAC ACL Rules Show map access-list macQueue cos-map4-257 Show map access-list mac Syntax Show map access-list mac interfaceMap access-list mac Match access-list macShow access-list ACL Information40 ACL Information 41 Snmp Commands Snmp CommandsShow access-group This command shows the port assignments of ACLsSnmp-server Syntax No snmp-server Default SettingNone Show snmpSnmp-server community Snmp-server contactSyntax Snmp-server contact string no snmp-server contact Syntax Snmp-server location text no snmp-server location Snmp-server locationSnmp-server host 156157 158 Issue authentication and link-up-down traps Snmp-server enable trapsSnmp-server host Snmp-server engine-idThis command shows the Snmp engine ID This example shows the default engine IDShow snmp engine-id Defaultview includes access to the entire MIB tree Snmp-server view42 show snmp engine-id display description This view includes MIB-2 This command shows information on the Snmp viewsShow snmp view ExamplesSnmp-server group 164Show snmp group Command Usage44 show snmp group display description 166Snmp-server user Default Setting168 This command shows information on Snmp users Show snmp user45 show snmp user display description 46 Interface Commands Interface CommandsSyntax Description string no description InterfaceDescription Port-channel channel-idRangeInterface Configuration Ethernet, Port Channel Speed-duplexFollowing example adds a description to port Syntax No negotiation Default Setting NegotiationNegotiation 4-173capabilities Following example configures port 11 to use autonegotiation CapabilitiesNegotiation 4-173speed-duplex Negotiation 4-173speed-duplex4-172 flowcontrol Syntax No flowcontrol Default SettingFlow control enabled FlowcontrolShutdown Following example enables flow control on portSyntax No shutdown Default Setting All interfaces are enabledFollowing example disables port Switchport broadcast packet-rateSyntax Clear counters interface This command clears statistics on an interfacePort-channel channel-idRange Default Setting Clear countersShows the status for all interfaces This command displays the status for an interfaceShow interfaces status Syntax Show interfaces status interfaceShows the counters for all interfaces This command displays interface statisticsShow interfaces counters Syntax Show interfaces counters interface181 Shows all interfaces Show interfaces switchportSyntax Show interfaces switchport interface This example shows the configuration setting for portField Description 47 show interfaces switchport display descriptionPort monitor Mirror Port Commands48 Mirror Port Commands Interface Configuration Ethernet, destination portShows all sessions This command displays mirror informationShow port monitor Syntax Show port monitor interfaceRate Limit Commands Following shows mirroring configured from port 6 to port49 Rate Limit Commands Rate-limit Interface Configuration Ethernet, Port Channel50 Link Aggregation Commands Link Aggregation CommandsGeneral Guidelines Guidelines for Creating TrunksSyntax Channel-group channel-idno channel-group Syntax no lacp Default SettingChannel-group Lacp191 32768 Lacp system-priorityLacp admin-keyEthernet Interface Syntax Lacp admin-key key no lacp admin-key Lacp admin-key Port ChannelLacp port-priority Default Setting51 show lacp counters display description This command displays Lacp informationShow lacp Port Channel all52 show lacp internal display description 197Partner 53 show lacp neighbors display description 199Address Table Commands 55 Address Table Commands54 show lacp sysid display description Mac-address-table static Mac-address- MAC addressVlan-id- Vlan ID Range Clear mac-address-table dynamic Show mac-address-tableMac-address- MAC address Mask Bits to match in the address Seconds Mac-address-table aging-timeSpanning Tree Commands 56 Spanning Tree CommandsShow mac-address-table aging-time RSTP/MSTP Syntax No spanning-tree Default Setting Spanning tree is enabledSpanning-tree Rstp Spanning-tree modeSpanning-tree forward-time 208Seconds Spanning-tree hello-timeSpanning-tree max-age 210Spanning-tree default priority Spanning-tree priorityIeee 802.1t format Long method Spanning-tree pathcost methodThis command limits the maximum transmission rate for BPDUs Spanning-tree transmission-limitCount -The transmission limit in seconds. Range Spanning-tree backup-root Spanning-tree mst-configurationSyntax No spanning-tree backup-root Default Setting Mst vlan MST ConfigurationMst instanceid priority priority no mst instanceid priority Mst priorityName Name of the spanning tree Switch’s MAC addressName Syntax name nameNumber Revision number of the spanning tree. Range RevisionMax-hops Syntax revision numberSpanning-tree spanning-disabled Syntax No spanning-tree spanning-disabled Default SettingThis example disables the Spanning Tree Algorithm for port Syntax Spanning-tree cost cost no spanning-tree cost Spanning-tree costSyntax No spanning-tree edge-port Spanning-tree port-prioritySpanning-tree edge-port Priority The priority for a port. Range 0-240, in stepsSpanning-tree portfast Syntax No spanning-tree portfast Default SettingSpanning-treeedge-port4-221 Spanning-tree link-typeAuto Spanning-tree mst costSpanning-tree mst port-priority4-225 Spanning-tree mst port-priorityPort-channel channel-idRange Command Mode Spanning-tree protocol-migrationSyntax Spanning-tree protocol-migration interface Syntax Show spanning-tree interface mst instanceid Show spanning-tree228 229 Show spanning-tree mst configurationVlan database Vlan Commands57 Vlan Commands Editing Vlan GroupsVlan By default only Vlan 1 exists and is activeConfiguring Vlan Interfaces Vlan Database Configuration59 Configuring Vlan Interfaces Interface vlan Syntax Interface vlan vlan-idShutdown Switchport mode Syntax Switchport mode trunk hybrid no switchport modeAll ports are in hybrid mode with the Pvid set to Vlan All frame types Switchport acceptable-frame-typesSyntax No switchport ingress-filtering Default Setting Switchport ingress-filtering237 Switchport native vlan238 Switchport allowed vlanSwitchport forbidden vlan 239No VLANs are included in the forbidden list 60 Displaying Vlan Information 240Displaying Vlan Information Show vlanFollowing example shows how to display information for Vlan 61 Private Vlan Commands241 242 Private-vlan 243244 Private-vlan associationNo private-vlan primary-vlan-idassociation Switchport mode private-vlan 245Normal Vlan Switchport private-vlan host-association Switchport private-vlan mapping246 247 Show vlan private-vlanSyntax Show vlan private-vlan community primary Gvrp and Bridge Extension Commands 62 Gvrp and Bridge Extension Commands248 Show bridge-ext Syntax No bridge-ext gvrp Default Setting249 Bridge-ext gvrpSyntax Show gvrp configuration interface Switchport gvrpShow gvrp configuration Syntax No switchport gvrp Default SettingGarp timer Shows both global and interface-specific configuration251 252 Show garp timerSyntax Show garp timer interface Shows all Garp timersPriority Commands 63 Priority Commands253 Syntax Queue mode strict wrr no queue mode Priority Commands LayerQueue mode 64 Priority Commands LayerQueue bandwidth 255256 Switchport priority defaultQueue cos-map 257258 65 Default CoS Priority LevelsShow queue bandwidth Show queue modeThis command shows the current queue mode 259Show queue cos-map Priority Commands Layer 366 Priority Commands Layer 3 260261 Syntax No map ip port Default Setting262 Syntax No map ip precedence Default SettingList below shows the default priority mapping 26367 Mapping IP Precedence to CoS Values 264 Syntax No map ip dscp Default Setting68 Mapping IP Dscp to CoS Values 265Syntax Show map ip port interface This command shows the IP port priority map266 Show map ip portSyntax Show map ip precedence interface This command shows the IP precedence priority map267 Show map ip precedenceSyntax Show map ip dscp interface This command shows the IP Dscp priority map268 Show map ip dscp70 Igmp Snooping Commands Multicast Filtering CommandsIgmp Snooping Commands 69 Multicast Filtering CommandsIp igmp snooping Syntax No ip igmp snooping Default SettingFollowing example enables Igmp snooping 270Igmp Version Following configures the switch to use Igmp Version271 Ip igmp snooping version272 Show ip igmp snoopingShow mac-address-table multicast Ip igmp snooping querier Igmp Query Commands Layer71 Igmp Query Commands Layer 273274 Ip igmp snooping query-countTimes Following shows how to configure the query count to 275Ip igmp snooping query-interval Seconds The report delay advertised in Igmp queries. Range 276Ip igmp snooping query-max-response-time Switch must use IGMPv2 for this command to take effect 277Ip igmp snooping router-port-expire-time Ip igmp snooping vlan mrouter Static Multicast Routing Commands72 Static Multicast Routing Commands 278Syntax Show ip igmp snooping mrouter vlan vlan-id Displays multicast router ports for all configured VLANs279 Show ip igmp snooping mrouterIp address IP Interface Commands73 IP Interface Command Syntax 280281 Interface Configuration VlanIp dhcp restart Ip default-gatewaySyntax Ip default-gateway gateway no ip default-gateway 282Show ip interface 283Ping This command has no default for the host284 Show ip redirects285 DNS Commands 74 DNS Commands286 This example maps two address to a host name 287Ip host No static entriesSyntax Clear host name 288Clear host Ip domain-name289 Ip domain-listSyntax No ip domain-list name 290 Ip name-serverIp domain-name4-288 Ip domain-name4-288 ip domain-lookup4-291 Syntax No ip domain-lookup Default Setting291 Ip domain-lookup292 Show hostsIp domain-name4-288 ip name-server4-290 Show dns This command displays the configuration of the DNS serverThis command displays entries in the DNS cache 29375 Show DNS Output Description This command clears all entries in the DNS cache294 Clear dns cachePoE AuthenticationAccess Control Lists Dhcp Client Port ConfigurationSpanning Tree Protocol Class of ServiceAdditional Features Port TrunkingSNMPv3 StandardsManagement Information Bases Problems Accessing the Management Interface Table B-1 Troubleshooting ChartSymptom Action Cannot access Using System Logs Troubleshooting Glossary-1 Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Glossary-7 Glossary-8 Virtual LAN VlanXModem Index-1 IndexIgmp Index-2Index-3 Index-4 Page For Technical SUPPORT, Call