Modules USSI-2 Test CLR | ADTRAN 1200305L1 guide

Section 4, User Interface Guide	ATLAS 550 System Manual

MODULES (USSI-2) > TEST > CLR

Write security: 4; Read security: 4

Clears error counters on test pattern results menu.

MODULES (USSI-2) > DTE INTERFACE

Write security: 5; Read security: 5

Configures the Dual USSI Module for the appropriate interface type. Select the parameters matching the interface cable being used.

MODULES (USSI-2) > DTE INTERFACE > PRT

Read security: 5

Displays the port number.

MODULES (USSI-2) > DTE INTERFACE > DTE INTERFACE MODE

Write security: 3; Read security: 5

Configures the Dual USSI Module interface type. The following options are available:

AUTO	The ATLAS 550 will automatically detect the interface type. The
	cable must be connected before the interface can be determined.
EIA-530A	Configures the interface for EIA-530A use.
EIA-530\RS-449\V.36Configures the interface for EIA-530, RS-449, or V.36 use.
X.21/V.11	Configures the interface for X.21 or V.11 use.
RS-232	Configures the interface for RS-232 use.

The following Dual USSI Option Module Systems are available (each includes the appropriate interface cable):

•RS-449/V.36 System (P/N 4200754L1)

• EIA-530/530A System (P/N 4200754L2)

•X.21/V.11 System (P/N 4200754L3)

•RS-232 System (P/N 4200754L4)

MODULES (USSI-2) > DTE INTERFACE > CURRENT DTE TYPE

Read security: 5

Displays the current configuration of the Dual USSI Module DTE Interface.

MODULES MENU (QUAD BASIC RATE ISDN (U INTERFACE) OPTION MODULE)

The ATLAS 550 system controller automatically detects the presence of the Quad BRI (U Interface) Option Module when it is installed in the system (listed as U-BRI-4). To see the menus for the Quad BRI (U Interface) Option Module via the terminal menu, use the arrow keys to scroll to the MODULES menu and press <Enter> to access the module choices. Refer to the Quad BRI (U Interface) Option Module Quick Start Guide for a menu tree containing a complete listing of menus.

144

© 2002 ADTRAN, Inc.

61200305L1-1F

Image 144

ADTRAN 1200305L1 system manual Modules USSI-2 Test CLR, Modules USSI-2 DTE Interface PRT

Contents

Atlas Trademarks To the Holder of the Manual Network Turnup Procedure Detail Level ProceduresConfiguration Guides About this Manual MIB Revision History Safety Instructions Save These Important Safety Instructions Affidavit Requirements for Connection to Digital Services ADTRAN, Inc Running H/F 1 doc title Running H/F 1 doc title ADTRAN, Inc REN FIC Usoc Running H/F 1 doc title ADTRAN, Inc ADTRAN, Inc Running H/F 1 doc title Warranty and Customer Service Limited Product Warranty Customer Service, Product Support Information, and Training Repair and ReturnPre-Sales Inquiries and Applications Support Installation and Maintenance Support Post-Sale SupportTraining Contents System Description Features and Benefits Configuration and ManagementSoftware Upgradeable Signaling Support Isdn Switch Types Switched Connection MapsTesting PPP Switching Option Modules T1/PRI Network Interface Module P/N 1200307L1 E1/PRA Network Interface Module P/N 1200308L1 Modem Management Network Module P/N 1200341L1BRI DBU Network Interface Module P/N 1200327L1 Dual Nx 56/64 Option Module P/N 1200311L1 Octal Ethernet Switch Option Module P/N 1200766L1 Octal/Quad FXS Option Module P/N 1200309L1/1200328L1Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Octal E&M Option Module P/N 1200313L1 Channel Adpcm Resource Module P/N 1200752L1 Nx 56/64 BONDing Resource Module P/N 1200326L1 System Description Atlas 550 System Manual At-A-Glance Specifications Engineering GuidelinesReviewing the Front Panel Design Reviewing the Rear Panel Design Tables Equipment Dimensions Power RequirementsACO Switch Reviewing the Front Panel Design Craft Port Front Panel LEDs Feature Description Option Module LEDs ACO SwitchFor these LEDs This color light Indicates that Power Craft Port Status Module StatusModule Online Module Test Reviewing the Rear Panel Design AC SystemDC System Connector type RJ-48C Control in Pinout Connector type RJ-48C Control OUT PinoutControl in Port Control OUT Port Alarm Relay Connection Connector type UsocAlarm Relay Connector Pinout Name Description Ethernet Connection External Alarm Relay Monitor Connection Shows the pinout for the External Alarm Relay connectorNetwork Interface Modules T1/PRI Network Interface 15-pin Male D-connector Pinout Test Interface E1/PRA Network Interface 15-pin Female D-connector Pinout Modem Management Network Module 6-pin Modular Jack Pinout BRI DBU Network Module P/N 1200327L1 Option Module InterfacesBRI Pinout FXS Pinout FXO Pinout 35 Winchester PinoutPin DB-78 Connector Pinout PIN Signal Description EIA-530 Connector Pinout System part number EIA-530A Connector Pinout RS-449/V.36 Connector Pinout RS-232 Connector Pinout Ccitt X.21/V.11 Connector Pinout M Pinout Trunk Circuit Connections for Various E&M Signaling Types Quad BRI U-Interface Option Module P/N 1200315L1Trunk Circuit Connections T1/PRI Pinout Quad BRI Isdn S/T Interface Option Module P/N 1200764L1 NxT1 Hssi Option Module P/N 1200346L1BRI Pinout S/T Interface Hssi SCSI-50 Connection Pinout PIN# + side PIN# side Hssi SCSI-50 Connection Pinout HSSI/V.35 Connection Pinout PIN# + side PIN# side Connector Types HSSI/V.35 Connection PinoutT1 Network Connection Pinout EIA-232 and V.35 Connection Pinouts Octal Ethernet Switch Option Module P/N 1200766L1 AT-A-GLANCE Specifications Lists the specifications for the Atlas 550 systemSpecifications Application Feature TDM Applications Switching Applications Specifications Application Feature IP Routing Specifications Application Feature Voice Compression Adpcm Engineering Guidelines Atlas 550 System Manual Network Turnup Procedure Unpack and Inspect the SystemGrounding Instructions Mounting Options Contents of Adtran Shipments IntroductionTools Required Unpack and Inspect the System Supplying Power to the Unit AC Powered SystemsGrounding Instructions DC Powered Systems Installing Network and Option ModulesMounting Options Shipping Contents Modem Management Network Module P/N 1200341L1 Dual Ussi Option Module System P/N 4200754Lx Quad Basic Rate Isdn U-Interface Option Module P/N 1200315L1 Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Ethernet Switch Option Module P/N 1200766L1 Network Turnup Procedure Atlas 550 System Manual User Interface Guide Selecting the Appropriate Menu Security Levels User Interface Guide Atlas 550 System Manual Atlas 550 System Manual User Interface Guide Navigating the Terminal Menu Terminal Menu WindowMenu Path Left Pane Alternate Menu View Window Pane Navigation To do this Press this key Navigating using the Keyboard Keys Right Window Pane NotationThis notation Means that Session Management Keystrokes To do this Set up the operational configuration for the Atlas Terminal Menu and System ControlSelecting the Appropriate Menu Review and monitor system status for the Atlas Password Security Levels Security LevelsMenu Descriptions To do this Go to this menu System Info Displays the boot ROM revision System Status Displays the source of the event Displays the port in which the event occurredDisplays a description of the event Indicates the current status of the Ethernet port Indicates whether the Ethernet network is 10 or 100BaseT Normal condition Failure conditionNo Information Available Configures the statistics displayed under data tables User Interface Guide Atlas 550 System Manual Performs reset daily at 1200 AM Performs reset on Saturday night, 1200 AMDisplay for collected resource usage data Displays the usage data broken down by slots and ports System Config System Config Session Timeout System Config Ethernet Port MAC Address System Config Snmp Snmp Access Defines Snmp managers characteristics as follows Enables and disables Snmp trap transmissionSpecifies the IP address of the network manager Defines the destination for Snmp traps as follows System Config Snmp Traps Destination Community System Config Snmp DS1 Total Perf Thresholds ESF System Config Snmp DS1 Total Perf Thresholds Total ES Thrsh System Config Snmp SNMP/ASP Proxy System Config Snmp SNMP/ASP Polling System Config Syslog Setup License key System Config Bonding Config Txfa Timer System Config Alarm Relay Threshold System Utility System Utility Update Firmware Transfer Method Indicates the status of the current update Indicates the time of the previous updateIndicates the slot number Defines the type of module for each slot Indicates the current status of the transfer Indicates the status of the previous transfer Self-tests disrupt data flow Displays which slot and port is currently being tested Index number of the log Atlas 550 slot numberAtlas 550 port number Event description Clears the self-test log Specifies the IP address to ping System Utility Ping Round Trip MAX Displays status from current Telnet client sessions System Utility Factory Default System Modules Modules Type Modules T1/PRI-1 Info Displays the assembly revision of the module Displays the current T1 alarm statusIndicates a loss of signal detected on port interface Receiving remote alarm RAI on port Modules T1/PRI-1 DS0 Alarms Modules T1/PRI-1 DS0 StatusModules T1/PRI-1 SIG Status Line Errored Second Not be obtainedControlled Slip Second Unavailable Second Modules T1/PRI-1 Configuration LBO Displays the port number Modules T1/PRI-1 Configuration Adlp Over FDL Modules T1/PRI-1 TestModules T1/PRI-1 Test PRT Modules T1/PRI-1 Test LOC LB Modules T1/PRI-1 Test Remote LB Modules T1/PRI-1 Test PatternModules T1/PRI-1 Test QRSS/RLB Results Modules T1/PRI-1 Test CLR Displays the current E1 alarm status Modules E1/PRA-1 InfoModules E1/PRA-1 PRT Displays the E1 framer hardware revision Modules E1/PRA-1 Alarms Modules E1/PRA-1 TS0 AlarmsModules E1/PRA-1 TS0 Status Modules E1/PRA-1 SIG Status Modules E1/PRA-1 Configuration Nfas Modules E1/PRA-1 Configuration TS16 MFModules E1/PRA-1 Configuration CRC-4 Modules E1/PRA-1 Test Modules E1/PRA-1 Test PRTModules E1/PRA-1 Test LOC LB Information Modules E1/PRA-1 Test Pattern Modules E1/PRA-1 Test Qrss ResultsModules E1/PRA-1 Test CLR Modules E1/PRA-1 Test INJ Displays the assembly revision Displays the part number of the moduleDisplays the serial number of the module Provides testing capabilities for the internal modem Displays the results of the last Detect Dial Tone test Indicates the current status of a particular Bonding session Bonding Modules DBU Bonding Configuration TXADD01 Timer Near-end block errors Far-end block errorsDisplays the port number Modules T1/PRI-2/4 Info Modules T1/PRI-2/4 Info Part Number Modules T1/PRI-2/4 Alarm Status Modules T1/PRI-2/4 Alarm Status PRTModules T1/PRI-2/4 Info PLL Status Modules T1/PRI-2/4 DS0 Status Modules T1/PRI-2/4 DS0 Alarms Modules T1/PRI-2/4 SIG Status Modules T1/PRI-2/4 Performance 15MINModules T1/PRI-2/4 Performance 24HR Modules T1/PRI-2/4 Configuration LBO Modules T1/PRI-2/4 Configuration Adlp Over FDL Modules T1/PRI-2/4 TestModules T1/PRI-2/4 Test PRT Modules T1/PRI-2/4 Test LOC LB Modules T1/PRI-2/4 Test Remote LB Modules T1/PRI-2/4 Test PatternModules T1/PRI-2/4 Test QRSS/RLB Results Modules T1/PRI-2/4 Test CLR Modules V35NX-2 Info Following signals are monitored these options are read-only Displays the Phase Lock Loop PLL and Fifo status Modules V35NX-2 PLL/FIFOModules V35NX-2 PLL/FIFO Port Clears inband statistic results Modules V35NX-2 PLL/FIFO PLL/FIFO Receive data Fifo emptyReceive data Fifo full Transmit data Fifo empty Test Follows Off Modules V35NX-2 Dial Mode Modules V35NX-2 DialModules V35NX-2 Dial PRT Modules V35NX-2 Dial Dial Modules V35NX-2 Test Modules V35NX-2 Test 511 ResultLoopback toward the network Code Modules V35NX-2 Test CLR Modules USSI-2 Info Modules USSI-2 DTE Status DTE Status Modules USSI-2 Data Rate Modules USSI-2 PLL/FIFO Displays the data rate of the selected portProvides information on the inband channel statistics Modules USSI-2 PLL/FIFO Port Modules USSI-2 PLL/FIFO PLL/FIFO Modules USSI-2 Configuration CTS Modules USSI-2 Dial Mode Modules USSI-2 DialModules USSI-2 Dial PRT Modules USSI-2 Dial Dial Modules USSI-2 Test Port Modules USSI-2 Test 511 ResultModules USSI-2 Test Inject Modules USSI-2 Test CLR Modules USSI-2 DTE InterfaceModules USSI-2 DTE Interface PRT Modules U-BRI-4 Alarms Modules U-BRI-4 Alarms PRTDetected with the endpoint or a cabling problem Modules U-BRI-4 Info Modules U-BRI-4 Test Modules U-BRI-4 Test PRT Modules ST-BRI-4 Alarms Modules ST-BRI-4 Alarms PRTModules ST-BRI-4 Info Loops the entire physical interface Modules ST-BRI-4 Alarms Alarms Modules ST-BRI-4 Test Modules ST-BRI-4 Test PRTOption Module Modules FXS-4/8 Info Modules FXS-4/8 StatusDisplays the processor ID of the selected module Displays the status of each of the FXS ports Modules FXS-4/8 Status PRT Modules FXS-4/8 Status RX Abcd Modules FXS-4/8 Status TX Abcd Modules FXS-4/8 TestModules FXS-4/8 Test Port Modules FXS-4/8 Test Test 2W Modules FXS-4/8 Config Modules FXS-4/8 Config PRTModules FXS-4/8 Test TX Abcd Modules FXS-4/8 Test 1KHZ Tone Modules FXS-4/8 Config RX Gain Modules FXS-4/8 Config TX GainModules FXO-4/8 Info Modules FXO-4/8 Status Modules FXO-4/8 Status PRTDisplays the status of each of the FXO ports Modules FXO-4/8 Status RX Abcd Modules FXO-4/8 Status TX AbcdModules FXO-4/8 Test Modules FXO-4/8 Test Port Modules FXO-4/8 Config Modules FXO-4/8 Config PRTModules FXO-4/8 Test TX Abcd Modules FXO-4/8 Test 1KHZ Tone Modules FXO-4/8 Config RX Gain Modules FXO-4/8 Config TX Gain Modules E&M-8 Status Modules E&M-8 Status PRTDisplays the status of each of the eight E&M ports Modules E&M-8 Status RX Abcd Modules E&M-8 Status TX AbcdModules E&M-8 Test Modules E&M-8 Test Port Modules E&M-8 Config Modules E&M-8 Config VF IfceModules E&M-8 Test 1KHZ Tone Normal operation Modules E&M-8 Config RX Gain Data terminal ready from DTE Modules LEGACY-4 Port Stats ERR FR Displays the firmware revision of the installed module Modules Menu NXT1 Hssi and NXT1 HSSI/V.35 Option ModulesModules NXT1 Hssi Info Modules NXT1HSSI T1 Menus Indicates a loss of signal detected on the port interface Modules NXT1HSSI Performance 15MIN Modules NXT1HSSI Test Modules NXT1HSSI Test PortModules NXT1HSSI Test LOC LB Modules NXT1HSSI Imux Menus Config Modules NXT1HSSI Imux MenusModules NXT1HSSI Imux Menus Status Modules NXT1HSSI Imux Menus Status Port Modules NXT1HSSI Imux Menus Config Port Modules NXT1HSSI Imux Menus Config GRP AssocModules NXT1HSSI Hssi Menus Modules NXT1HSSI Hssi Menus Status Hssi Interface Loopback Test Diagram Following loopback status messages may display Modules NXT1HSSI Hssi Menus Status CA Modules NXT1HSSI Hssi Menus Status LA and LBModules NXT1HSSI Hssi Menus Status LC Modules NXT1HSSI Hssi Menus Status TA Modules NXT1HSSI Hssi Menus Config Modules NXT1HSSI Hssi Menus Config Port NameModules NXT1HSSI Hssi Menus Config TX CLK Modules NXT1HSSI Hssi Menus Config CTS Modules NXT1HSSI Hssi Menus Config DCD Modules NXT1HSSI Hssi Menus Config CAModules NXT1HSSI Hssi Menus Test Modules NXT1HSSI Hssi Menus Test Port Modules NXT1HSSI Hssi Menus Test Remote Lpbk Hssi Modules ENET-8 InfoModules ENET-8 Status Modules ENET-8 Status Port Modules VCOM-X Info This resource was reinitialized after excessive errors Principle applies to the VCOM-8, 24, and 32 Option ModulesThis resource is currently changing state This resource is currently in use Ccitt G.723.1 compression 6.3 kbps bandwidth Proprietary Netcoder compression 6.4 kbps bandwidth Is between protocol states Dual-tone, multi-frequency Dtmf digit receivedVoice status until the FAX protocol is established Session Marking a device as Disabled prevents the Atlas 550 from Any calls routed to it Modules VCOM-X Statistics Atlas Frms Modules VCOM-X Statistics Atlas Drop Modules ADPCM-32 Info Modules ADPCM-32 Status Modules ADPCM-32 Status DeviceModules ADPCM-32 Status Status Displays the status of each of the packet voice resources Modules ADPCM-32 Config Modules ADPCM-32 Config Configure ADPCM-32 Devices Modules ADPCM-32 Statistics Atlas Frms Modules ADPCM-32 Statistics Atlas Drop Modules ADPCM-32 Statistics ADPCM-32 FrmsModules ADPCM-32 Statistics ADPCM-32 Drop Displays the board revision of the installed module Modules Bonding InfoModules Bonding Status Displays the current status of the Bonding session Modules Bonding Status Bonded EP Modules Bonding Configuration Txdeq Timer SEC Packet Manager Interface NNI mode Signaling using ITU-T Q.933-ASignaling using Ansi T1.617-D Signaling using Group of Four Sent configuration request Enabled, occurs nowIs waiting for an acknowledge But the peer has not acknowledged us Endpoint on all PVCs ViolationsClears all values in this submenu Resets the Tx and Rx packet counters Clears all values in this submenuDisplays the current state of the LCP negotiations Number of packets transmitted over this link Resets all sublink counters Local address for each PVC as assigned by the carrierTotal number of Fecn bits received on this PVC Creates and configures packet endpoints Total number of Becn bits received on this PVCFor Adtran internal use only Remote device does not support frame relay signaling Operates in NNI modeActs as the network side of the UNI interface Acts as the user side of the UNI interface Displays the configuration for this packet endpoint Contains the Authentication parameters for this endpoint Username that the peer will use to authenticate the Atlas Password that the peer will use to authenticate the AtlasThis turns on authentication debugging This turns on LCP negotiation debugging Packet Manager Packet Endpnts Config Config Sdlc User-definable name for the Dlci Allows configuration of parameters for each Dlci This Dlci disregards the status as reported from the switchTate to a UTO for normal operation Reports Active to all packet endpoints within Atlas Diagnostic Mode Provides switching options Forces a switch to backupDisables backup switching Provides normal operation Displays the name of the packet endpoint Displays the protocol running on the packet endpointDisplays the user-defined name for the Dlci Displays the test mode for the PVC Shows the duration in seconds for the fixed-duration test Displays the average round trip delay for the current test Resets the countersDisplays the total number of packet endpoints configured Indicates data source Indicates data destination Displays the port number and name Within the given link Displays the Data Link Connection Identifier circuit numberIndicates collection of IQ data for the target Dlci Sets the parameters for IQ statistics gathering Number of frames the port received for the interval or day Number of bytes the port received for the interval or day Time, in seconds, the signaling state has been down Number of PVC-signaling, full-status frames receivedNumber of PVC-signaling, full-status frames transmitted Number of frames received with CRC errors Number of single PVC status frames receivedNumber of frames discarded by the IQ unit Number of frames received without proper flag termination Packet Manager Frame Relay IQ View IQ Statistics Sublink Number of DEs the PVC has received for the interval or day Number of CRs the PVC has received for the interval or day Number of lost frames on the PVC for the interval or day Minimum frame size the PVC received for the interval or dayMaximum frame size the PVC received for the interval or day Average frame size the PVC received for the interval or day Number of state changes for this PVC for the interval or day Router Router IP ARP Cache Router IP ARP Cache IP AddressRouter IP ARP Cache MAC Address Adds a static route to the router Router IP ARP Cache Time Router IP ARP Cache Type Clears the Used menu and resets the value to zero Router IP Routes TTL Dlci Number Route tableRoute address see the following, Far-End Address On this virtual circuit Are listened toThis virtual circuit No modification of the routing metric Defines when RIP advertisements are transmitted Defines the secret used to advertise routes when using RIPRIP advertisements are periodically transmitted Learned routes do not age Router IP Ping Specifies the number of pings to send. The maximum value is Ctrl + \ Ctrl + Shift + Received in error HostTransport layer protocol Destination address was not a local address 550, and the Source-Route option processing was successful IP Statistics Name Description Having errors bad Icmp checksums, bad length, etc Number of Icmp Parameter Problem messages receivedNumber of Icmp Parameter Problem messages sent Clears the accumulated statistics Number of Icmp Echo request messages sent Number of Icmp Echo Reply messages sentNumber of Icmp Timestamp request messages sent Number of Icmp Timestamp Reply messages sent Established or CLOSE-WAIT Excluding those containing only retransmitted octetsTotal number of UDP datagrams delivered to UDP users Destination port Router IP UDP Relay Enable Enables/disables the router to act as a relay agentRouter IP UDP Relay Specifies the UDP port 1 to 65,535 in the UDP Port columns Dedicated Maps Displays the index number of the available maps Dedicated Maps CREATE/EDIT Maps Connects Port Specifies which days of the week the map is active T1 Trunk Conditioning Service TS0 Rate Defines ports to be used for this connection Answer Supervision Rx AB Tx AB Dedicated Maps FXO CREATE/EDIT Maps Connects TO/FROM Config Sets the DS0 rate to either 56 or 64 kbps Dedicated Maps Ussi CREATE/EDIT Maps Connects TO/FROM Config Dedicated Maps NXT1 Hssi and NXT1 HSSI/V.35 Modules DS0S Available Configures the port to use Flags or Ones as the idle code Legacy Data Option Module Receive Idle Code Voice Port This activator forces a link in/out of backup Circuit Status Menu Attempting to dial the backup link Will retry backup dialing in num secondsLink is in error and waiting on backup Link is answering a backup endpoint No current test call on this dedicated dial backup circuit Passed last manual or scheduled testFailed last manual or scheduled test Dial Plan Dial Plan Network Term PORT/PEP Dial Plan Network Term OUT#ACCEPT Accept Number Dial Plan Network Term OUT#ACCEPT Treat Call AS Dial Plan Network Term Subst Templ ORIGINAL# Equipment. In this case, Atlas 550 is acting as the network Dial Plan User Term IN#ACCEPT SRC ID IXC trunks are unavailable busy or in alarm. In this case, Primary endpoints are unavailablePrimary accept number for the local exchange would be N$, Secondary accept would be 1$ Dial Plan User Term Ifce Config Dial Plan User Term Subst Templ Local area code. Use for sending caller ID to the network Use extreme caution when forcing Collision Response Specifies the configuration parameters for the endpoint AT&T 4ESS Dial Plan T1/PRI Network Term PRI Ifce Config PRI Strip MSD Switched Digital Network AT&T SDN Dial Plan T1/PRI Network Term RBS Would be used if availableContiguous channels from last to first Send a progress message to the CPE and map busy tones Dial Plan T1/PRI Network Term RBS Ifce Config RBS Dial Plan T1/PRI Network Term RBS Ifce Config RBS First DS0From the network Loop Start Dial Plan T1/PRI Network Term RBS Ifce Config RBS did Digits ANI/DNIS Dial Plan T1/PRI Network Term RBS Ifce Config RBS Strip MSD Dial Plan T1/PRI Network Term RBS Ifce Config RBS Source IDMust define the trunk number 272 ADTRAN, Inc Dial Plan T1/PRI User Term PRI Would be used if availableAmong the available DS0s on this interface Received Dial Plan T1/PRI User Term PRI Ifce Config PRI Strip MSD Dial Plan T1/PRI User Term PRI Ifce Config PRI Swap ANI/DNIS Dial Plan T1/PRI User Term RBS Ifce Config RBS Dial Plan T1/PRI User Term RBS Ifce Config RBS First DS0Dial Plan T1/PRI User Term RBS 61200305L1-1F ADTRAN, Inc 277 Dial Plan T1/PRI User Term RBS Ifce Config RBS Strip MSD Dial Plan T1/PRI User Term RBS Ifce Config RBS Source IDThrough this endpoint. This item is optional Dial on Offhook number must be specific i.e., no wildcards Dial Plan T1/PRI User Term RBS Ifce Config RBS DS0 Selection Dial Plan E1/PRA Network Term PRA Ifce Config PRA First DS0 Dial Plan E1/PRA Network Term PRA Ifce Config PRA Source ID Dial Plan E1/PRA User Term PRA Dial Plan E1/PRA User Term PRA Ifce Config PRA Swap ANI/DNIS Phone numbers assigned to this BRI phone line Spid Number Dial Plan U-BRI User Term Dial Plan U-BRI User Term Ifce Config Strip MSD From the Network Pstn Caller ID number must be specific i.e., no wild cards Available Contiguous ports from last to first Dial Plan FXS User Term Ifce Config ANI to Caller ID Dial Plan FXO Network Term Ifce Config Number of Ports Dial Plan FXO Network Term Ifce Config Strip MSD DPT Dial Plan FXO User Term Ifce Config Direct Inward Dialing Dial Plan Octal E&M Module Dial Plan E&M User Term Dial Plan E&M User Term Ifce Config Signaling Method Dial Plan E&M User Term Ifce Config Source ID Specifies the number to dial on an outgoing call Dial Plan V35NX User Term Ifce Config Source ID Dial Plan Ussi User Term Ifce Config Ports Available Dial Plan Ussi User Term Ifce Config MIN DS0’S Selects the time delay in seconds between redial attempts For User terminations, the number of calls is fixed atDefines the number dialed to originate a call Defines the number of redials to attempt Dial Plan PKT Endpt User Term Ifce Config Call Party Number Endpoint will originate the backup call Backup if an error is detectedBackup This only applies to originating endpoints RED, Yellow, or Blue alarms When network is out of alarmOnly by the Manual activator This is the time of day to enable dial backup How often test calls are to be made Date of the next scheduled test call Selects the appropriate Dlci for this dial plan entry Dial Plan PKT Voice Network Term Ifce Config did Prefix Dial Plan PKT Voice Network Term Ifce Config Strip MSD Dial Plan PKT Voice User Term Ifce Config Conflict Report Dial Plan PKT Voice User Term Ifce Config Strip MSD Detail Level Procedures DLP-Index Atlas 550 System Manual Connecting the Terminal or PC to the CONTROL/CRAFT Port Introduction DLP-001 Perform Steps Below in the Order Listed Logging in to the System DLP-002 61200305L1-1F ADTRAN, Inc 321 322 ADTRAN, Inc Setting IP Parameters for the Atlas Enter the appropriate Default Gateway Enter the appropriate IP addressEnter the appropriate Subnet Mask Access to a PC or other computer connected to the LAN Verifying Communications Over AN IP LAN DLP-004 Atlas 550 System Manual DLP-004 Telnet to the Atlas 328 ADTRAN, Inc ADDING/REMOVING Users and Changing Password Security Levels VT100 terminal or PC with VT100 terminal emulation software DLP-005 Select level... If you want the user to Updating the Firmware Using Tftp DLP-006 Atlas 550 System Manual DLP-006 334 ADTRAN, Inc Updating the Firmware Using Xmodem DLP-007 Atlas 550 System Manual DLP-007 338 ADTRAN, Inc Saving the Current Configuration Using Tftp DLP-008 Respond with Y to confirm request Loading a Configuration Using Tftp DLP-009 Respond with Y to confirmation request Saving the Current Configuration Using Xmodem DLP-010 Loading a Configuration Using Xmodem Review the steps above for possible configuration errors DLP-011 Connecting the Atlas 550 to AN External Modem DLP-012 Atlas 550 System Manual DLP-012 350 ADTRAN, Inc Using the Adtran Utility Syslog with the Atlas Setting Up the Atlas 550 to use the Syslog Setting Up the Syslog Host Additional Syslog Features 354 ADTRAN, Inc Connecting the Alarm Contacts Alarm Relay Connector Pinout DLP-014 Atlas 550 System Manual DLP-014 358 ADTRAN, Inc Using the Alarm Connections and ACO Button DLP-015 Perform the Steps Below in the Order Listed Clearing the Alarm Relay Remotely 362 ADTRAN, Inc Configuration Guides CFG-6 Atlas 550 System Manual Dial Backup for Dedicated T1 Circuits Before You Begin Configuring the Dedicated T1 Data Link CFG-001 61200305L1-1F ADTRAN, Inc 367 368 ADTRAN, Inc Configuring the Dial Backup PRI 370 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 371 Configuring the Dial Backup Endpoint SLT field in the Dedicated MAP ORIGINATE/ANSWER MIN DS0S 376 ADTRAN, Inc System Event Logging Setting the Event LOG Category Atlas 550 System Manual System Event Logging Viewing the Events System Events System Controller Events Console Log String Category Switchboard Events Console Log String Category System Controller EventsConsole Log String Category Event Nx 56/64 Events Console Log String Category Nx 56/64 Events T1 Events Console Log String Category T1 Events Ethernet Events Isdn Events Circuit Backup Events DP Outgoing Signaling Events Isdn Cause CodesModem Management Module Events Console Log String Category Isdn Cause Code Events Category Incompatibledest Major Interworkingunspec Cause Code LOG Entries Cause Code Log Entry Location DesignationsCode Location Isdn Layer 2 Lapd Message 390 ADTRAN, Inc Adtran Utilities Telnet UtilityVT100 Utility Tftp Server Telnet Utility Telnet Menu Tree Click on Session to open the Telnet session Establishes the Telnet sessionConnect Provides Copy and Paste commands Ends the Telnet session and closes the Telnet screenProvides viewing alternatives for the terminal screen Echoes each character that you enter Provides on-line help for using the Adtran Utilities VT100 UtilityOpens the on-line help Displays version and owner information Opens VT100 terminal emulation session Opens a specified serial port for a VT100 sessionUploads and downloads files to and from an Atlas Selects the Xmodem file transfer protocol Provides terminal screen commands Identical to the Telnet Edit Menu see Edit Menu onRedraws the screen Identical to Telnet Colors Menu see Colors on Tftp Server Tftp Server Interface Menu Tree Provides enable, disable, abort, and exit options Terminates a transfer that is in progressTerminates active transfers and closes the Tftp window Provides print options Log Field Xmit meter provides a visual record of the transfer process MIB MIBs Supported by the Atlas MIB Compilation Order Traps Supported by the Atlas 404 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 405 MIB Variables Supported by the Atlas IpDefaultTTL IpInHdrErrorsIpInAddrErrors IpForwarding IpReasmTimeout IcmpInErrorsIpForwDatagrams IpInUnknownProtos IcmpInSrcQuenchs IcmpOutErrorsIcmpInRedirects IcmpInEchos TcpEstabResets TcpInSegsTcpAttemptFails TcpCurrEstab 61200305L1-1F ADTRAN, Inc 411 Rfc1406.mib 6.1.2.1.10.18 61200305L1-1F ADTRAN, Inc 413 Rfc1315.mib 6.1.2.1.10.32 Adtran.mib 6.1.4.1.664 Ads1.mib 6.1.4.1.664.2.3 Atunit.mib 6.1.4.1.664.2.154.1.5 Atmod.mib 6.1.4.1.664.2.154.1.6 Atv35nx.mib 6.1.4.1.664.2.154.1.7 Atbri.mib 6.1.4.1.664.2.154.1.8 Att1.mib 6.1.4.1.664.2.154.1.9 61200305L1-1F ADTRAN, Inc 421 Atvoice.mib 6.1.4.1.664.2.154.1.10 Athssv35.mib 6.1.4.1.664.2.154.1.11 At550.mib 6.1.4.1.664.2.219 Atqbriu.mib 6.1.4.1.664.2.274 Fperform.mib 6.1.4.1.664.4.1 61200305L1-1F ADTRAN, Inc 425 426 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 427 428 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 429 430 ADTRAN, Inc