Index number of the log, Atlas 550 slot number | ADTRAN 1200305L1

ATLAS 550 System Manual	Section 4, User Interface Guide

The result of the self-test on each installed port is listed with Pass/Fail results. Figure 7 depicts a typical test log. The fields included in the log are described below the figure.

Figure 7. View Selftest Log

The self-test log includes the following fields:

IDX	Index number of the log.
TIME	Time and date of the log entry.
SL	ATLAS 550 slot number.
PT	ATLAS 550 port number.
EVENT	Event description.
RESULT	Show PASS/FAIL results.

The tests associated with the system controller are shown in Table 2.

	Table 2. ATLAS 550 System Controller Self-Test Log

THIS EVENT...		LOGS THIS RESULT...

Flash		Flash memory checksum verified

BootRom		Boot ROM checksum verified

DSP RAM		Memory associated with the Digital Signal Processor

RTC RAM		Memory associated with the real time clock

NV Batt		Tests the battery associated with non-volatile memory

TDM RAM		Memory associated with mapping TDM bandwidth

DRAM		Dynamic RAM used for program execution

HDLC		The High-Level Data Link Controllers

Card Tst		Tests the data path for each slot in the system with an installed module.

61200305L1-1F

© 2002 ADTRAN, Inc.

97

Image 97

ADTRAN 1200305L1 system manual Index number of the log, Atlas 550 slot number, Atlas 550 port number, Event description

Contents

Atlas To the Holder of the Manual Trademarks Detail Level Procedures Network Turnup ProcedureConfiguration Guides About this Manual Revision History MIB Save These Important Safety Instructions Safety Instructions Affidavit Requirements for Connection to Digital Services ADTRAN, Inc Running H/F 1 doc title Running H/F 1 doc title ADTRAN, Inc REN FIC Usoc Running H/F 1 doc title ADTRAN, Inc ADTRAN, Inc Running H/F 1 doc title Limited Product Warranty Warranty and Customer Service Repair and Return Customer Service, Product Support Information, and TrainingPre-Sales Inquiries and Applications Support Post-Sale Support Installation and Maintenance SupportTraining System Description Contents Configuration and Management Features and BenefitsSoftware Upgradeable Signaling Support Switched Connection Maps Isdn Switch TypesTesting PPP Switching T1/PRI Network Interface Module P/N 1200307L1 Option Modules Modem Management Network Module P/N 1200341L1 E1/PRA Network Interface Module P/N 1200308L1BRI DBU Network Interface Module P/N 1200327L1 Dual Nx 56/64 Option Module P/N 1200311L1 Octal/Quad FXS Option Module P/N 1200309L1/1200328L1 Octal Ethernet Switch Option Module P/N 1200766L1Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Octal E&M Option Module P/N 1200313L1 Nx 56/64 BONDing Resource Module P/N 1200326L1 Channel Adpcm Resource Module P/N 1200752L1 System Description Atlas 550 System Manual Engineering Guidelines At-A-Glance SpecificationsReviewing the Front Panel Design Reviewing the Rear Panel Design Tables Power Requirements Equipment DimensionsACO Switch Reviewing the Front Panel Design Front Panel LEDs Craft Port ACO Switch Feature Description Option Module LEDsFor these LEDs This color light Indicates that Power Craft Port Module Status StatusModule Online Module Test AC System Reviewing the Rear Panel DesignDC System Connector type RJ-48C Control OUT Pinout Connector type RJ-48C Control in PinoutControl in Port Control OUT Port Connector type Usoc Alarm Relay ConnectionAlarm Relay Connector Pinout Name Description Ethernet Connection Shows the pinout for the External Alarm Relay connector External Alarm Relay Monitor ConnectionNetwork Interface Modules Test Interface T1/PRI Network Interface 15-pin Male D-connector Pinout Modem Management Network Module 6-pin Modular Jack Pinout E1/PRA Network Interface 15-pin Female D-connector Pinout Option Module Interfaces BRI DBU Network Module P/N 1200327L1BRI Pinout FXS Pinout 35 Winchester Pinout FXO PinoutPin PIN Signal Description DB-78 Connector Pinout System part number EIA-530 Connector Pinout RS-449/V.36 Connector Pinout EIA-530A Connector Pinout RS-232 Connector Pinout M Pinout Ccitt X.21/V.11 Connector Pinout Quad BRI U-Interface Option Module P/N 1200315L1 Trunk Circuit Connections for Various E&M Signaling TypesTrunk Circuit Connections T1/PRI Pinout NxT1 Hssi Option Module P/N 1200346L1 Quad BRI Isdn S/T Interface Option Module P/N 1200764L1BRI Pinout S/T Interface Hssi SCSI-50 Connection Pinout PIN# + side PIN# side HSSI/V.35 Connection Pinout PIN# + side PIN# side Hssi SCSI-50 Connection Pinout HSSI/V.35 Connection Pinout Connector TypesT1 Network Connection Pinout EIA-232 and V.35 Connection Pinouts Octal Ethernet Switch Option Module P/N 1200766L1 Lists the specifications for the Atlas 550 system AT-A-GLANCE SpecificationsSpecifications Application Feature TDM Applications Switching Applications IP Routing Specifications Application Feature Adpcm Specifications Application Feature Voice Compression Engineering Guidelines Atlas 550 System Manual Unpack and Inspect the System Network Turnup ProcedureGrounding Instructions Mounting Options Introduction Contents of Adtran ShipmentsTools Required Unpack and Inspect the System AC Powered Systems Supplying Power to the UnitGrounding Instructions Installing Network and Option Modules DC Powered SystemsMounting Options Shipping Contents Modem Management Network Module P/N 1200341L1 Quad Basic Rate Isdn U-Interface Option Module P/N 1200315L1 Dual Ussi Option Module System P/N 4200754Lx Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Ethernet Switch Option Module P/N 1200766L1 Network Turnup Procedure Atlas 550 System Manual Selecting the Appropriate Menu Security Levels User Interface Guide User Interface Guide Atlas 550 System Manual Atlas 550 System Manual User Interface Guide Terminal Menu Window Navigating the Terminal MenuMenu Path Left Pane To do this Press this key Alternate Menu View Window Pane Navigation Right Window Pane Notation Navigating using the Keyboard KeysThis notation Means that To do this Session Management Keystrokes Terminal Menu and System Control Set up the operational configuration for the AtlasSelecting the Appropriate Menu Review and monitor system status for the Atlas Security Levels Password Security LevelsMenu Descriptions To do this Go to this menu System Info Displays the boot ROM revision System Status Displays the port in which the event occurred Displays the source of the eventDisplays a description of the event Indicates whether the Ethernet network is 10 or 100BaseT Indicates the current status of the Ethernet port Failure condition Normal conditionNo Information Available User Interface Guide Atlas 550 System Manual Configures the statistics displayed under data tables Performs reset on Saturday night, 1200 AM Performs reset daily at 1200 AMDisplay for collected resource usage data Displays the usage data broken down by slots and ports System Config System Config Session Timeout System Config Ethernet Port MAC Address System Config Snmp Snmp Access Enables and disables Snmp trap transmission Defines Snmp managers characteristics as followsSpecifies the IP address of the network manager Defines the destination for Snmp traps as follows System Config Snmp Traps Destination Community ESF System Config Snmp DS1 Total Perf Thresholds System Config Snmp DS1 Total Perf Thresholds Total ES Thrsh System Config Snmp SNMP/ASP Polling System Config Snmp SNMP/ASP Proxy System Config Syslog Setup License key System Config Bonding Config Txfa Timer System Config Alarm Relay Threshold System Utility System Utility Update Firmware Transfer Method Indicates the time of the previous update Indicates the status of the current updateIndicates the slot number Defines the type of module for each slot Indicates the status of the previous transfer Indicates the current status of the transfer Displays which slot and port is currently being tested Self-tests disrupt data flow Atlas 550 slot number Index number of the logAtlas 550 port number Event description Specifies the IP address to ping Clears the self-test log System Utility Ping Round Trip MAX Displays status from current Telnet client sessions System Utility Factory Default System Modules Modules Type Modules T1/PRI-1 Info Displays the current T1 alarm status Displays the assembly revision of the moduleIndicates a loss of signal detected on port interface Receiving remote alarm RAI on port Modules T1/PRI-1 DS0 Status Modules T1/PRI-1 DS0 AlarmsModules T1/PRI-1 SIG Status Not be obtained Line Errored SecondControlled Slip Second Unavailable Second Displays the port number Modules T1/PRI-1 Configuration LBO Modules T1/PRI-1 Test Modules T1/PRI-1 Configuration Adlp Over FDLModules T1/PRI-1 Test PRT Modules T1/PRI-1 Test LOC LB Modules T1/PRI-1 Test Pattern Modules T1/PRI-1 Test Remote LBModules T1/PRI-1 Test QRSS/RLB Results Modules T1/PRI-1 Test CLR Modules E1/PRA-1 Info Displays the current E1 alarm statusModules E1/PRA-1 PRT Displays the E1 framer hardware revision Modules E1/PRA-1 TS0 Alarms Modules E1/PRA-1 AlarmsModules E1/PRA-1 TS0 Status Modules E1/PRA-1 SIG Status Modules E1/PRA-1 Configuration TS16 MF Modules E1/PRA-1 Configuration NfasModules E1/PRA-1 Configuration CRC-4 Modules E1/PRA-1 Test PRT Modules E1/PRA-1 TestModules E1/PRA-1 Test LOC LB Information Modules E1/PRA-1 Test Qrss Results Modules E1/PRA-1 Test PatternModules E1/PRA-1 Test CLR Modules E1/PRA-1 Test INJ Displays the part number of the module Displays the assembly revisionDisplays the serial number of the module Displays the results of the last Detect Dial Tone test Provides testing capabilities for the internal modem Indicates the current status of a particular Bonding session Bonding Modules DBU Bonding Configuration TXADD01 Timer Far-end block errors Near-end block errorsDisplays the port number Modules T1/PRI-2/4 Info Part Number Modules T1/PRI-2/4 Info Modules T1/PRI-2/4 Alarm Status PRT Modules T1/PRI-2/4 Alarm StatusModules T1/PRI-2/4 Info PLL Status Modules T1/PRI-2/4 DS0 Status Modules T1/PRI-2/4 DS0 Alarms Modules T1/PRI-2/4 Performance 15MIN Modules T1/PRI-2/4 SIG StatusModules T1/PRI-2/4 Performance 24HR Modules T1/PRI-2/4 Configuration LBO Modules T1/PRI-2/4 Test Modules T1/PRI-2/4 Configuration Adlp Over FDLModules T1/PRI-2/4 Test PRT Modules T1/PRI-2/4 Test LOC LB Modules T1/PRI-2/4 Test Pattern Modules T1/PRI-2/4 Test Remote LBModules T1/PRI-2/4 Test QRSS/RLB Results Modules T1/PRI-2/4 Test CLR Modules V35NX-2 Info Following signals are monitored these options are read-only Modules V35NX-2 PLL/FIFO Displays the Phase Lock Loop PLL and Fifo statusModules V35NX-2 PLL/FIFO Port Clears inband statistic results Receive data Fifo empty Modules V35NX-2 PLL/FIFO PLL/FIFOReceive data Fifo full Transmit data Fifo empty Follows Off Test Modules V35NX-2 Dial Modules V35NX-2 Dial ModeModules V35NX-2 Dial PRT Modules V35NX-2 Dial Dial Modules V35NX-2 Test 511 Result Modules V35NX-2 TestLoopback toward the network Code Modules USSI-2 Info Modules V35NX-2 Test CLR Modules USSI-2 Data Rate Modules USSI-2 DTE Status DTE Status Displays the data rate of the selected port Modules USSI-2 PLL/FIFOProvides information on the inband channel statistics Modules USSI-2 PLL/FIFO PLL/FIFO Modules USSI-2 PLL/FIFO Port Modules USSI-2 Configuration CTS Modules USSI-2 Dial Modules USSI-2 Dial ModeModules USSI-2 Dial PRT Modules USSI-2 Dial Dial Modules USSI-2 Test 511 Result Modules USSI-2 Test PortModules USSI-2 Test Inject Modules USSI-2 DTE Interface Modules USSI-2 Test CLRModules USSI-2 DTE Interface PRT Modules U-BRI-4 Alarms PRT Modules U-BRI-4 AlarmsDetected with the endpoint or a cabling problem Modules U-BRI-4 Info Modules U-BRI-4 Test PRT Modules U-BRI-4 Test Modules ST-BRI-4 Alarms PRT Modules ST-BRI-4 AlarmsModules ST-BRI-4 Info Loops the entire physical interface Modules ST-BRI-4 Alarms Alarms Modules ST-BRI-4 Test PRT Modules ST-BRI-4 TestOption Module Modules FXS-4/8 Status Modules FXS-4/8 InfoDisplays the processor ID of the selected module Displays the status of each of the FXS ports Modules FXS-4/8 Status RX Abcd Modules FXS-4/8 Status PRT Modules FXS-4/8 Test Modules FXS-4/8 Status TX AbcdModules FXS-4/8 Test Port Modules FXS-4/8 Test Test 2W Modules FXS-4/8 Config PRT Modules FXS-4/8 ConfigModules FXS-4/8 Test TX Abcd Modules FXS-4/8 Test 1KHZ Tone Modules FXS-4/8 Config TX Gain Modules FXS-4/8 Config RX GainModules FXO-4/8 Info Modules FXO-4/8 Status PRT Modules FXO-4/8 StatusDisplays the status of each of the FXO ports Modules FXO-4/8 Status TX Abcd Modules FXO-4/8 Status RX AbcdModules FXO-4/8 Test Modules FXO-4/8 Test Port Modules FXO-4/8 Config PRT Modules FXO-4/8 ConfigModules FXO-4/8 Test TX Abcd Modules FXO-4/8 Test 1KHZ Tone Modules FXO-4/8 Config TX Gain Modules FXO-4/8 Config RX Gain Modules E&M-8 Status PRT Modules E&M-8 StatusDisplays the status of each of the eight E&M ports Modules E&M-8 Status TX Abcd Modules E&M-8 Status RX AbcdModules E&M-8 Test Modules E&M-8 Test Port Modules E&M-8 Config VF Ifce Modules E&M-8 ConfigModules E&M-8 Test 1KHZ Tone Normal operation Modules E&M-8 Config RX Gain Data terminal ready from DTE Modules LEGACY-4 Port Stats ERR FR Modules Menu NXT1 Hssi and NXT1 HSSI/V.35 Option Modules Displays the firmware revision of the installed moduleModules NXT1 Hssi Info Modules NXT1HSSI T1 Menus Indicates a loss of signal detected on the port interface Modules NXT1HSSI Performance 15MIN Modules NXT1HSSI Test Port Modules NXT1HSSI TestModules NXT1HSSI Test LOC LB Modules NXT1HSSI Imux Menus Modules NXT1HSSI Imux Menus ConfigModules NXT1HSSI Imux Menus Status Modules NXT1HSSI Imux Menus Status Port Modules NXT1HSSI Imux Menus Config GRP Assoc Modules NXT1HSSI Imux Menus Config PortModules NXT1HSSI Hssi Menus Modules NXT1HSSI Hssi Menus Status Following loopback status messages may display Hssi Interface Loopback Test Diagram Modules NXT1HSSI Hssi Menus Status LA and LB Modules NXT1HSSI Hssi Menus Status CAModules NXT1HSSI Hssi Menus Status LC Modules NXT1HSSI Hssi Menus Status TA Modules NXT1HSSI Hssi Menus Config Port Name Modules NXT1HSSI Hssi Menus ConfigModules NXT1HSSI Hssi Menus Config TX CLK Modules NXT1HSSI Hssi Menus Config CTS Modules NXT1HSSI Hssi Menus Config CA Modules NXT1HSSI Hssi Menus Config DCDModules NXT1HSSI Hssi Menus Test Modules NXT1HSSI Hssi Menus Test Port Modules ENET-8 Info Modules NXT1HSSI Hssi Menus Test Remote Lpbk HssiModules ENET-8 Status Modules ENET-8 Status Port Modules VCOM-X Info Principle applies to the VCOM-8, 24, and 32 Option Modules This resource was reinitialized after excessive errorsThis resource is currently changing state This resource is currently in use Proprietary Netcoder compression 6.4 kbps bandwidth Ccitt G.723.1 compression 6.3 kbps bandwidth Dual-tone, multi-frequency Dtmf digit received Is between protocol statesVoice status until the FAX protocol is established Session Any calls routed to it Marking a device as Disabled prevents the Atlas 550 from Modules VCOM-X Statistics Atlas Drop Modules VCOM-X Statistics Atlas Frms Modules ADPCM-32 Info Modules ADPCM-32 Status Device Modules ADPCM-32 StatusModules ADPCM-32 Status Status Displays the status of each of the packet voice resources Modules ADPCM-32 Config Configure ADPCM-32 Devices Modules ADPCM-32 Config Modules ADPCM-32 Statistics Atlas Frms Modules ADPCM-32 Statistics ADPCM-32 Frms Modules ADPCM-32 Statistics Atlas DropModules ADPCM-32 Statistics ADPCM-32 Drop Modules Bonding Info Displays the board revision of the installed moduleModules Bonding Status Displays the current status of the Bonding session Modules Bonding Status Bonded EP Modules Bonding Configuration Txdeq Timer SEC Packet Manager Signaling using ITU-T Q.933-A Interface NNI modeSignaling using Ansi T1.617-D Signaling using Group of Four Enabled, occurs now Sent configuration requestIs waiting for an acknowledge But the peer has not acknowledged us Violations Endpoint on all PVCsClears all values in this submenu Clears all values in this submenu Resets the Tx and Rx packet countersDisplays the current state of the LCP negotiations Number of packets transmitted over this link Local address for each PVC as assigned by the carrier Resets all sublink countersTotal number of Fecn bits received on this PVC Total number of Becn bits received on this PVC Creates and configures packet endpointsFor Adtran internal use only Operates in NNI mode Remote device does not support frame relay signalingActs as the network side of the UNI interface Acts as the user side of the UNI interface Contains the Authentication parameters for this endpoint Displays the configuration for this packet endpoint Password that the peer will use to authenticate the Atlas Username that the peer will use to authenticate the AtlasThis turns on authentication debugging This turns on LCP negotiation debugging Packet Manager Packet Endpnts Config Config Sdlc User-definable name for the Dlci This Dlci disregards the status as reported from the switch Allows configuration of parameters for each DlciTate to a UTO for normal operation Reports Active to all packet endpoints within Atlas Diagnostic Mode Forces a switch to backup Provides switching optionsDisables backup switching Provides normal operation Displays the protocol running on the packet endpoint Displays the name of the packet endpointDisplays the user-defined name for the Dlci Shows the duration in seconds for the fixed-duration test Displays the test mode for the PVC Resets the counters Displays the average round trip delay for the current testDisplays the total number of packet endpoints configured Indicates data destination Indicates data source Displays the port number and name Displays the Data Link Connection Identifier circuit number Within the given linkIndicates collection of IQ data for the target Dlci Sets the parameters for IQ statistics gathering Number of bytes the port received for the interval or day Number of frames the port received for the interval or day Number of PVC-signaling, full-status frames received Time, in seconds, the signaling state has been downNumber of PVC-signaling, full-status frames transmitted Number of single PVC status frames received Number of frames received with CRC errorsNumber of frames discarded by the IQ unit Number of frames received without proper flag termination Packet Manager Frame Relay IQ View IQ Statistics Sublink Number of CRs the PVC has received for the interval or day Number of DEs the PVC has received for the interval or day Minimum frame size the PVC received for the interval or day Number of lost frames on the PVC for the interval or dayMaximum frame size the PVC received for the interval or day Average frame size the PVC received for the interval or day Number of state changes for this PVC for the interval or day Router Router IP ARP Cache IP Address Router IP ARP CacheRouter IP ARP Cache MAC Address Adds a static route to the router Router IP ARP Cache Type Router IP ARP Cache Time Router IP Routes TTL Clears the Used menu and resets the value to zero Route table Dlci NumberRoute address see the following, Far-End Address Are listened to On this virtual circuitThis virtual circuit No modification of the routing metric Defines the secret used to advertise routes when using RIP Defines when RIP advertisements are transmittedRIP advertisements are periodically transmitted Learned routes do not age Specifies the number of pings to send. The maximum value is Router IP Ping Ctrl + \ Ctrl + Shift + Host Received in errorTransport layer protocol Destination address was not a local address IP Statistics Name Description 550, and the Source-Route option processing was successful Number of Icmp Parameter Problem messages received Having errors bad Icmp checksums, bad length, etcNumber of Icmp Parameter Problem messages sent Clears the accumulated statistics Number of Icmp Echo Reply messages sent Number of Icmp Echo request messages sentNumber of Icmp Timestamp request messages sent Number of Icmp Timestamp Reply messages sent Excluding those containing only retransmitted octets Established or CLOSE-WAITTotal number of UDP datagrams delivered to UDP users Destination port Enables/disables the router to act as a relay agent Router IP UDP Relay EnableRouter IP UDP Relay Specifies the UDP port 1 to 65,535 in the UDP Port columns Dedicated Maps Displays the index number of the available maps Dedicated Maps CREATE/EDIT Maps Connects Port Specifies which days of the week the map is active T1 Trunk Conditioning Service TS0 Rate Defines ports to be used for this connection Answer Supervision Rx AB Tx AB Dedicated Maps FXO CREATE/EDIT Maps Connects TO/FROM Config Sets the DS0 rate to either 56 or 64 kbps Dedicated Maps Ussi CREATE/EDIT Maps Connects TO/FROM Config Dedicated Maps NXT1 Hssi and NXT1 HSSI/V.35 Modules DS0S Available Legacy Data Option Module Configures the port to use Flags or Ones as the idle code Receive Idle Code Voice Port Circuit Status Menu This activator forces a link in/out of backup Will retry backup dialing in num seconds Attempting to dial the backup linkLink is in error and waiting on backup Link is answering a backup endpoint Passed last manual or scheduled test No current test call on this dedicated dial backup circuitFailed last manual or scheduled test Dial Plan Dial Plan Network Term PORT/PEP Dial Plan Network Term OUT#ACCEPT Accept Number Dial Plan Network Term OUT#ACCEPT Treat Call AS Dial Plan Network Term Subst Templ ORIGINAL# Equipment. In this case, Atlas 550 is acting as the network Dial Plan User Term IN#ACCEPT SRC ID Primary endpoints are unavailable IXC trunks are unavailable busy or in alarm. In this case,Primary accept number for the local exchange would be N$, Secondary accept would be 1$ Dial Plan User Term Ifce Config Dial Plan User Term Subst Templ Local area code. Use for sending caller ID to the network Use extreme caution when forcing Collision Response AT&T 4ESS Specifies the configuration parameters for the endpoint Dial Plan T1/PRI Network Term PRI Ifce Config PRI Strip MSD AT&T SDN Switched Digital Network Would be used if available Dial Plan T1/PRI Network Term RBSContiguous channels from last to first Send a progress message to the CPE and map busy tones Dial Plan T1/PRI Network Term RBS Ifce Config RBS First DS0 Dial Plan T1/PRI Network Term RBS Ifce Config RBSFrom the network Loop Start ANI/DNIS Dial Plan T1/PRI Network Term RBS Ifce Config RBS did Digits Dial Plan T1/PRI Network Term RBS Ifce Config RBS Source ID Dial Plan T1/PRI Network Term RBS Ifce Config RBS Strip MSDMust define the trunk number 272 ADTRAN, Inc Would be used if available Dial Plan T1/PRI User Term PRIAmong the available DS0s on this interface Received Dial Plan T1/PRI User Term PRI Ifce Config PRI Strip MSD Dial Plan T1/PRI User Term PRI Ifce Config PRI Swap ANI/DNIS Dial Plan T1/PRI User Term RBS Ifce Config RBS First DS0 Dial Plan T1/PRI User Term RBS Ifce Config RBSDial Plan T1/PRI User Term RBS 61200305L1-1F ADTRAN, Inc 277 Dial Plan T1/PRI User Term RBS Ifce Config RBS Source ID Dial Plan T1/PRI User Term RBS Ifce Config RBS Strip MSDThrough this endpoint. This item is optional Dial on Offhook number must be specific i.e., no wildcards Dial Plan T1/PRI User Term RBS Ifce Config RBS DS0 Selection Dial Plan E1/PRA Network Term PRA Ifce Config PRA First DS0 Dial Plan E1/PRA Network Term PRA Ifce Config PRA Source ID Dial Plan E1/PRA User Term PRA Dial Plan E1/PRA User Term PRA Ifce Config PRA Swap ANI/DNIS Phone numbers assigned to this BRI phone line Spid Number Dial Plan U-BRI User Term Dial Plan U-BRI User Term Ifce Config Strip MSD From the Network Pstn Caller ID number must be specific i.e., no wild cards Contiguous ports from last to first Available Dial Plan FXS User Term Ifce Config ANI to Caller ID Dial Plan FXO Network Term Ifce Config Number of Ports Dial Plan FXO Network Term Ifce Config Strip MSD DPT Dial Plan FXO User Term Ifce Config Direct Inward Dialing Dial Plan Octal E&M Module Dial Plan E&M User Term Dial Plan E&M User Term Ifce Config Signaling Method Dial Plan E&M User Term Ifce Config Source ID Specifies the number to dial on an outgoing call Dial Plan V35NX User Term Ifce Config Source ID Dial Plan Ussi User Term Ifce Config Ports Available Dial Plan Ussi User Term Ifce Config MIN DS0’S For User terminations, the number of calls is fixed at Selects the time delay in seconds between redial attemptsDefines the number dialed to originate a call Defines the number of redials to attempt Dial Plan PKT Endpt User Term Ifce Config Call Party Number Backup if an error is detected Endpoint will originate the backup callBackup This only applies to originating endpoints When network is out of alarm RED, Yellow, or Blue alarmsOnly by the Manual activator How often test calls are to be made This is the time of day to enable dial backup Selects the appropriate Dlci for this dial plan entry Date of the next scheduled test call Dial Plan PKT Voice Network Term Ifce Config did Prefix Dial Plan PKT Voice Network Term Ifce Config Strip MSD Dial Plan PKT Voice User Term Ifce Config Conflict Report Dial Plan PKT Voice User Term Ifce Config Strip MSD Detail Level Procedures DLP-Index Atlas 550 System Manual Introduction Connecting the Terminal or PC to the CONTROL/CRAFT Port Perform Steps Below in the Order Listed DLP-001 Logging in to the System DLP-002 61200305L1-1F ADTRAN, Inc 321 322 ADTRAN, Inc Setting IP Parameters for the Atlas Enter the appropriate IP address Enter the appropriate Default GatewayEnter the appropriate Subnet Mask Verifying Communications Over AN IP LAN Access to a PC or other computer connected to the LAN DLP-004 Atlas 550 System Manual DLP-004 Telnet to the Atlas 328 ADTRAN, Inc VT100 terminal or PC with VT100 terminal emulation software ADDING/REMOVING Users and Changing Password Security Levels Select level... If you want the user to DLP-005 Updating the Firmware Using Tftp DLP-006 Atlas 550 System Manual DLP-006 334 ADTRAN, Inc Updating the Firmware Using Xmodem DLP-007 Atlas 550 System Manual DLP-007 338 ADTRAN, Inc Saving the Current Configuration Using Tftp Respond with Y to confirm request DLP-008 Loading a Configuration Using Tftp Respond with Y to confirmation request DLP-009 Saving the Current Configuration Using Xmodem DLP-010 Loading a Configuration Using Xmodem DLP-011 Review the steps above for possible configuration errors Connecting the Atlas 550 to AN External Modem DLP-012 Atlas 550 System Manual DLP-012 350 ADTRAN, Inc Using the Adtran Utility Syslog with the Atlas Setting Up the Syslog Host Setting Up the Atlas 550 to use the Syslog Additional Syslog Features 354 ADTRAN, Inc Connecting the Alarm Contacts DLP-014 Alarm Relay Connector Pinout Atlas 550 System Manual DLP-014 358 ADTRAN, Inc Using the Alarm Connections and ACO Button Perform the Steps Below in the Order Listed DLP-015 Clearing the Alarm Relay Remotely 362 ADTRAN, Inc Configuration Guides CFG-6 Atlas 550 System Manual Before You Begin Dial Backup for Dedicated T1 Circuits CFG-001 Configuring the Dedicated T1 Data Link 61200305L1-1F ADTRAN, Inc 367 368 ADTRAN, Inc Configuring the Dial Backup PRI 370 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 371 Configuring the Dial Backup Endpoint SLT field in the Dedicated MAP ORIGINATE/ANSWER MIN DS0S 376 ADTRAN, Inc System Event Logging Setting the Event LOG Category Atlas 550 System Manual System Event Logging Viewing the Events System Controller Events Console Log String Category System Events System Controller Events Switchboard Events Console Log String CategoryConsole Log String Category Event Nx 56/64 Events Console Log String Category T1 Events Console Log String Category Nx 56/64 Events Ethernet Events T1 Events Isdn Events Circuit Backup Events Isdn Cause Codes DP Outgoing Signaling EventsModem Management Module Events Console Log String Category Isdn Cause Code Events Category Incompatibledest Major Interworkingunspec Cause Code Log Entry Location Designations Cause Code LOG EntriesCode Location Isdn Layer 2 Lapd Message 390 ADTRAN, Inc Telnet Utility Adtran UtilitiesVT100 Utility Tftp Server Telnet Menu Tree Telnet Utility Establishes the Telnet session Click on Session to open the Telnet sessionConnect Ends the Telnet session and closes the Telnet screen Provides Copy and Paste commandsProvides viewing alternatives for the terminal screen Echoes each character that you enter VT100 Utility Provides on-line help for using the Adtran UtilitiesOpens the on-line help Displays version and owner information Opens a specified serial port for a VT100 session Opens VT100 terminal emulation sessionUploads and downloads files to and from an Atlas Selects the Xmodem file transfer protocol Identical to the Telnet Edit Menu see Edit Menu on Provides terminal screen commandsRedraws the screen Identical to Telnet Colors Menu see Colors on Tftp Server Interface Menu Tree Tftp Server Terminates a transfer that is in progress Provides enable, disable, abort, and exit optionsTerminates active transfers and closes the Tftp window Provides print options Xmit meter provides a visual record of the transfer process Log Field MIB MIBs Supported by the Atlas Traps Supported by the Atlas MIB Compilation Order 404 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 405 MIB Variables Supported by the Atlas IpInHdrErrors IpDefaultTTLIpInAddrErrors IpForwarding IcmpInErrors IpReasmTimeoutIpForwDatagrams IpInUnknownProtos IcmpOutErrors IcmpInSrcQuenchsIcmpInRedirects IcmpInEchos TcpInSegs TcpEstabResetsTcpAttemptFails TcpCurrEstab 61200305L1-1F ADTRAN, Inc 411 Rfc1406.mib 6.1.2.1.10.18 61200305L1-1F ADTRAN, Inc 413 Rfc1315.mib 6.1.2.1.10.32 Adtran.mib 6.1.4.1.664 Ads1.mib 6.1.4.1.664.2.3 Atunit.mib 6.1.4.1.664.2.154.1.5 Atv35nx.mib 6.1.4.1.664.2.154.1.7 Atmod.mib 6.1.4.1.664.2.154.1.6 Atbri.mib 6.1.4.1.664.2.154.1.8 Att1.mib 6.1.4.1.664.2.154.1.9 61200305L1-1F ADTRAN, Inc 421 Athssv35.mib 6.1.4.1.664.2.154.1.11 Atvoice.mib 6.1.4.1.664.2.154.1.10 At550.mib 6.1.4.1.664.2.219 Fperform.mib 6.1.4.1.664.4.1 Atqbriu.mib 6.1.4.1.664.2.274 61200305L1-1F ADTRAN, Inc 425 426 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 427 428 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 429 430 ADTRAN, Inc