Originate/Answer | ADTRAN 1200305L1 guide

Section 6, CFG-001	ATLAS 550 System Manual

5.Configure the IFCE CONFIG options for the backup link. These include the Dial Backup parameters. Navigate to the IFCE CONFIG option and press <Enter>. This will display a list of the Dial Backup options. The options are described following the figure.

•ORIGINATE/ANSWER

ORIGINATE: The ATLAS 550 will be the originating side in the event of a failure.

ANSWER: The ATLAS 550 will answer any incoming calls, but only go into backup if an error is detect- ed.

ANSWER ALWAYS: The ATLAS 550 will answer any incoming calls and immediately go into backup.

•OUTGOING CALL TYPE

DIGITAL 56K: Data rate for the backup endpoint is set to 56kbps.

DIGITAL 64K: Data rate for the backup endpoint is set to 64kbps.

•SOURCE ID

The SOURCE ID should remain in the default state unless it has been assigned elsewhere in the configu- ration. Please refer to the ATLAS 550 System Manual for a detailed discussion of the SOURCE ID field.

•OUTDIAL NUMBER

This field should contain the number you want the ATLAS 550 to dial upon going into backup.

•FORCE MODE:

AUTO: The ATLAS 550 will automatically follow the dial backup configuration parameters to go into backup.

FORCED: The ATLAS 550 must be manually forced to go into backup upon detection of a failure.

DISABLED: The ATLAS 550 will never go into backup regardless of data integrity.

•BACKUP CRITERIA

NET/DATA FAIL: DBU is initiated when either the network fails (possible causes include Red, Yellow, Blue, or LOS alarms) or when the Nx56/64 module detects a loss of data transitions on the V.35 inter- face. If NET/DATA FAIL is selected, the V.35 Nx INBAND option must be ON. The remote TSU inband must also be enabled.

NET FAIL: DBU is initiated when there is a network failure. Possible causes include LOS, Red, Yellow, or Blue alarms.

374

© 2002 ADTRAN, Inc.

61200305L1-1F

Image 374

ADTRAN 1200305L1 system manual Originate/Answer

Contents

Atlas Trademarks To the Holder of the Manual Configuration Guides Network Turnup ProcedureDetail Level Procedures About this Manual MIB Revision History Safety Instructions Save These Important Safety Instructions Affidavit Requirements for Connection to Digital Services ADTRAN, Inc Running H/F 1 doc title Running H/F 1 doc title ADTRAN, Inc REN FIC Usoc Running H/F 1 doc title ADTRAN, Inc ADTRAN, Inc Running H/F 1 doc title Warranty and Customer Service Limited Product Warranty Pre-Sales Inquiries and Applications Support Customer Service, Product Support Information, and TrainingRepair and Return Training Installation and Maintenance SupportPost-Sale Support Contents System Description Software Upgradeable Features and BenefitsConfiguration and Management Signaling Support Testing Isdn Switch TypesSwitched Connection Maps PPP Switching Option Modules T1/PRI Network Interface Module P/N 1200307L1 BRI DBU Network Interface Module P/N 1200327L1 E1/PRA Network Interface Module P/N 1200308L1Modem Management Network Module P/N 1200341L1 Dual Nx 56/64 Option Module P/N 1200311L1 Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Octal Ethernet Switch Option Module P/N 1200766L1Octal/Quad FXS Option Module P/N 1200309L1/1200328L1 Octal E&M Option Module P/N 1200313L1 Channel Adpcm Resource Module P/N 1200752L1 Nx 56/64 BONDing Resource Module P/N 1200326L1 System Description Atlas 550 System Manual Reviewing the Front Panel Design At-A-Glance SpecificationsEngineering Guidelines Reviewing the Rear Panel Design Tables ACO Switch Equipment DimensionsPower Requirements Reviewing the Front Panel Design Craft Port Front Panel LEDs For these LEDs This color light Indicates that Power Feature Description Option Module LEDsACO Switch Craft Port Module Online StatusModule Status Module Test DC System Reviewing the Rear Panel DesignAC System Control in Port Connector type RJ-48C Control in PinoutConnector type RJ-48C Control OUT Pinout Control OUT Port Alarm Relay Connector Pinout Name Description Alarm Relay ConnectionConnector type Usoc Ethernet Connection Network Interface Modules External Alarm Relay Monitor ConnectionShows the pinout for the External Alarm Relay connector T1/PRI Network Interface 15-pin Male D-connector Pinout Test Interface E1/PRA Network Interface 15-pin Female D-connector Pinout Modem Management Network Module 6-pin Modular Jack Pinout BRI Pinout BRI DBU Network Module P/N 1200327L1Option Module Interfaces FXS Pinout Pin FXO Pinout35 Winchester Pinout DB-78 Connector Pinout PIN Signal Description EIA-530 Connector Pinout System part number EIA-530A Connector Pinout RS-449/V.36 Connector Pinout RS-232 Connector Pinout Ccitt X.21/V.11 Connector Pinout M Pinout Trunk Circuit Connections Trunk Circuit Connections for Various E&M Signaling TypesQuad BRI U-Interface Option Module P/N 1200315L1 T1/PRI Pinout BRI Pinout S/T Interface Quad BRI Isdn S/T Interface Option Module P/N 1200764L1NxT1 Hssi Option Module P/N 1200346L1 Hssi SCSI-50 Connection Pinout PIN# + side PIN# side Hssi SCSI-50 Connection Pinout HSSI/V.35 Connection Pinout PIN# + side PIN# side T1 Network Connection Pinout Connector TypesHSSI/V.35 Connection Pinout EIA-232 and V.35 Connection Pinouts Octal Ethernet Switch Option Module P/N 1200766L1 Specifications Application Feature TDM Applications AT-A-GLANCE SpecificationsLists the specifications for the Atlas 550 system Switching Applications Specifications Application Feature IP Routing Specifications Application Feature Voice Compression Adpcm Engineering Guidelines Atlas 550 System Manual Grounding Instructions Network Turnup ProcedureUnpack and Inspect the System Mounting Options Tools Required Contents of Adtran ShipmentsIntroduction Unpack and Inspect the System Grounding Instructions Supplying Power to the UnitAC Powered Systems Mounting Options DC Powered SystemsInstalling Network and Option Modules Shipping Contents Modem Management Network Module P/N 1200341L1 Dual Ussi Option Module System P/N 4200754Lx Quad Basic Rate Isdn U-Interface Option Module P/N 1200315L1 Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Ethernet Switch Option Module P/N 1200766L1 Network Turnup Procedure Atlas 550 System Manual User Interface Guide Selecting the Appropriate Menu Security Levels User Interface Guide Atlas 550 System Manual Atlas 550 System Manual User Interface Guide Menu Path Left Pane Navigating the Terminal MenuTerminal Menu Window Alternate Menu View Window Pane Navigation To do this Press this key This notation Means that Navigating using the Keyboard KeysRight Window Pane Notation Session Management Keystrokes To do this Selecting the Appropriate Menu Set up the operational configuration for the AtlasTerminal Menu and System Control Review and monitor system status for the Atlas Menu Descriptions Password Security LevelsSecurity Levels To do this Go to this menu System Info Displays the boot ROM revision System Status Displays a description of the event Displays the source of the eventDisplays the port in which the event occurred Indicates the current status of the Ethernet port Indicates whether the Ethernet network is 10 or 100BaseT No Information Available Normal conditionFailure condition Configures the statistics displayed under data tables User Interface Guide Atlas 550 System Manual Display for collected resource usage data Performs reset daily at 1200 AMPerforms reset on Saturday night, 1200 AM Displays the usage data broken down by slots and ports System Config System Config Session Timeout System Config Ethernet Port MAC Address System Config Snmp Snmp Access Specifies the IP address of the network manager Defines Snmp managers characteristics as followsEnables and disables Snmp trap transmission Defines the destination for Snmp traps as follows System Config Snmp Traps Destination Community System Config Snmp DS1 Total Perf Thresholds ESF System Config Snmp DS1 Total Perf Thresholds Total ES Thrsh System Config Snmp SNMP/ASP Proxy System Config Snmp SNMP/ASP Polling System Config Syslog Setup License key System Config Bonding Config Txfa Timer System Config Alarm Relay Threshold System Utility System Utility Update Firmware Transfer Method Indicates the slot number Indicates the status of the current updateIndicates the time of the previous update Defines the type of module for each slot Indicates the current status of the transfer Indicates the status of the previous transfer Self-tests disrupt data flow Displays which slot and port is currently being tested Atlas 550 port number Index number of the logAtlas 550 slot number Event description Clears the self-test log Specifies the IP address to ping System Utility Ping Round Trip MAX Displays status from current Telnet client sessions System Utility Factory Default System Modules Modules Type Modules T1/PRI-1 Info Indicates a loss of signal detected on port interface Displays the assembly revision of the moduleDisplays the current T1 alarm status Receiving remote alarm RAI on port Modules T1/PRI-1 SIG Status Modules T1/PRI-1 DS0 AlarmsModules T1/PRI-1 DS0 Status Controlled Slip Second Line Errored SecondNot be obtained Unavailable Second Modules T1/PRI-1 Configuration LBO Displays the port number Modules T1/PRI-1 Test PRT Modules T1/PRI-1 Configuration Adlp Over FDLModules T1/PRI-1 Test Modules T1/PRI-1 Test LOC LB Modules T1/PRI-1 Test QRSS/RLB Results Modules T1/PRI-1 Test Remote LBModules T1/PRI-1 Test Pattern Modules T1/PRI-1 Test CLR Modules E1/PRA-1 PRT Displays the current E1 alarm statusModules E1/PRA-1 Info Displays the E1 framer hardware revision Modules E1/PRA-1 TS0 Status Modules E1/PRA-1 AlarmsModules E1/PRA-1 TS0 Alarms Modules E1/PRA-1 SIG Status Modules E1/PRA-1 Configuration CRC-4 Modules E1/PRA-1 Configuration NfasModules E1/PRA-1 Configuration TS16 MF Modules E1/PRA-1 Test LOC LB Modules E1/PRA-1 TestModules E1/PRA-1 Test PRT Information Modules E1/PRA-1 Test CLR Modules E1/PRA-1 Test PatternModules E1/PRA-1 Test Qrss Results Modules E1/PRA-1 Test INJ Displays the serial number of the module Displays the assembly revisionDisplays the part number of the module Provides testing capabilities for the internal modem Displays the results of the last Detect Dial Tone test Indicates the current status of a particular Bonding session Bonding Modules DBU Bonding Configuration TXADD01 Timer Displays the port number Near-end block errorsFar-end block errors Modules T1/PRI-2/4 Info Modules T1/PRI-2/4 Info Part Number Modules T1/PRI-2/4 Info PLL Status Modules T1/PRI-2/4 Alarm StatusModules T1/PRI-2/4 Alarm Status PRT Modules T1/PRI-2/4 DS0 Status Modules T1/PRI-2/4 DS0 Alarms Modules T1/PRI-2/4 Performance 24HR Modules T1/PRI-2/4 SIG StatusModules T1/PRI-2/4 Performance 15MIN Modules T1/PRI-2/4 Configuration LBO Modules T1/PRI-2/4 Test PRT Modules T1/PRI-2/4 Configuration Adlp Over FDLModules T1/PRI-2/4 Test Modules T1/PRI-2/4 Test LOC LB Modules T1/PRI-2/4 Test QRSS/RLB Results Modules T1/PRI-2/4 Test Remote LBModules T1/PRI-2/4 Test Pattern Modules T1/PRI-2/4 Test CLR Modules V35NX-2 Info Following signals are monitored these options are read-only Modules V35NX-2 PLL/FIFO Port Displays the Phase Lock Loop PLL and Fifo statusModules V35NX-2 PLL/FIFO Clears inband statistic results Receive data Fifo full Modules V35NX-2 PLL/FIFO PLL/FIFOReceive data Fifo empty Transmit data Fifo empty Test Follows Off Modules V35NX-2 Dial PRT Modules V35NX-2 Dial ModeModules V35NX-2 Dial Modules V35NX-2 Dial Dial Loopback toward the network Modules V35NX-2 TestModules V35NX-2 Test 511 Result Code Modules V35NX-2 Test CLR Modules USSI-2 Info Modules USSI-2 DTE Status DTE Status Modules USSI-2 Data Rate Provides information on the inband channel statistics Modules USSI-2 PLL/FIFODisplays the data rate of the selected port Modules USSI-2 PLL/FIFO Port Modules USSI-2 PLL/FIFO PLL/FIFO Modules USSI-2 Configuration CTS Modules USSI-2 Dial PRT Modules USSI-2 Dial ModeModules USSI-2 Dial Modules USSI-2 Dial Dial Modules USSI-2 Test Inject Modules USSI-2 Test PortModules USSI-2 Test 511 Result Modules USSI-2 DTE Interface PRT Modules USSI-2 Test CLRModules USSI-2 DTE Interface Detected with the endpoint or a cabling problem Modules U-BRI-4 AlarmsModules U-BRI-4 Alarms PRT Modules U-BRI-4 Info Modules U-BRI-4 Test Modules U-BRI-4 Test PRT Modules ST-BRI-4 Info Modules ST-BRI-4 AlarmsModules ST-BRI-4 Alarms PRT Loops the entire physical interface Modules ST-BRI-4 Alarms Alarms Option Module Modules ST-BRI-4 TestModules ST-BRI-4 Test PRT Displays the processor ID of the selected module Modules FXS-4/8 InfoModules FXS-4/8 Status Displays the status of each of the FXS ports Modules FXS-4/8 Status PRT Modules FXS-4/8 Status RX Abcd Modules FXS-4/8 Test Port Modules FXS-4/8 Status TX AbcdModules FXS-4/8 Test Modules FXS-4/8 Test Test 2W Modules FXS-4/8 Test TX Abcd Modules FXS-4/8 ConfigModules FXS-4/8 Config PRT Modules FXS-4/8 Test 1KHZ Tone Modules FXO-4/8 Info Modules FXS-4/8 Config RX GainModules FXS-4/8 Config TX Gain Displays the status of each of the FXO ports Modules FXO-4/8 StatusModules FXO-4/8 Status PRT Modules FXO-4/8 Test Modules FXO-4/8 Status RX AbcdModules FXO-4/8 Status TX Abcd Modules FXO-4/8 Test Port Modules FXO-4/8 Test TX Abcd Modules FXO-4/8 ConfigModules FXO-4/8 Config PRT Modules FXO-4/8 Test 1KHZ Tone Modules FXO-4/8 Config RX Gain Modules FXO-4/8 Config TX Gain Displays the status of each of the eight E&M ports Modules E&M-8 StatusModules E&M-8 Status PRT Modules E&M-8 Test Modules E&M-8 Status RX AbcdModules E&M-8 Status TX Abcd Modules E&M-8 Test Port Modules E&M-8 Test 1KHZ Tone Modules E&M-8 ConfigModules E&M-8 Config VF Ifce Normal operation Modules E&M-8 Config RX Gain Data terminal ready from DTE Modules LEGACY-4 Port Stats ERR FR Modules NXT1 Hssi Info Displays the firmware revision of the installed moduleModules Menu NXT1 Hssi and NXT1 HSSI/V.35 Option Modules Modules NXT1HSSI T1 Menus Indicates a loss of signal detected on the port interface Modules NXT1HSSI Performance 15MIN Modules NXT1HSSI Test LOC LB Modules NXT1HSSI TestModules NXT1HSSI Test Port Modules NXT1HSSI Imux Menus Status Modules NXT1HSSI Imux Menus ConfigModules NXT1HSSI Imux Menus Modules NXT1HSSI Imux Menus Status Port Modules NXT1HSSI Hssi Menus Modules NXT1HSSI Imux Menus Config PortModules NXT1HSSI Imux Menus Config GRP Assoc Modules NXT1HSSI Hssi Menus Status Hssi Interface Loopback Test Diagram Following loopback status messages may display Modules NXT1HSSI Hssi Menus Status LC Modules NXT1HSSI Hssi Menus Status CAModules NXT1HSSI Hssi Menus Status LA and LB Modules NXT1HSSI Hssi Menus Status TA Modules NXT1HSSI Hssi Menus Config TX CLK Modules NXT1HSSI Hssi Menus ConfigModules NXT1HSSI Hssi Menus Config Port Name Modules NXT1HSSI Hssi Menus Config CTS Modules NXT1HSSI Hssi Menus Test Modules NXT1HSSI Hssi Menus Config DCDModules NXT1HSSI Hssi Menus Config CA Modules NXT1HSSI Hssi Menus Test Port Modules ENET-8 Status Modules NXT1HSSI Hssi Menus Test Remote Lpbk HssiModules ENET-8 Info Modules ENET-8 Status Port Modules VCOM-X Info This resource is currently changing state This resource was reinitialized after excessive errorsPrinciple applies to the VCOM-8, 24, and 32 Option Modules This resource is currently in use Ccitt G.723.1 compression 6.3 kbps bandwidth Proprietary Netcoder compression 6.4 kbps bandwidth Voice status until the FAX protocol is established Is between protocol statesDual-tone, multi-frequency Dtmf digit received Session Marking a device as Disabled prevents the Atlas 550 from Any calls routed to it Modules VCOM-X Statistics Atlas Frms Modules VCOM-X Statistics Atlas Drop Modules ADPCM-32 Info Modules ADPCM-32 Status Status Modules ADPCM-32 StatusModules ADPCM-32 Status Device Displays the status of each of the packet voice resources Modules ADPCM-32 Config Modules ADPCM-32 Config Configure ADPCM-32 Devices Modules ADPCM-32 Statistics Atlas Frms Modules ADPCM-32 Statistics ADPCM-32 Drop Modules ADPCM-32 Statistics Atlas DropModules ADPCM-32 Statistics ADPCM-32 Frms Modules Bonding Status Displays the board revision of the installed moduleModules Bonding Info Displays the current status of the Bonding session Modules Bonding Status Bonded EP Modules Bonding Configuration Txdeq Timer SEC Packet Manager Signaling using Ansi T1.617-D Interface NNI modeSignaling using ITU-T Q.933-A Signaling using Group of Four Is waiting for an acknowledge Sent configuration requestEnabled, occurs now But the peer has not acknowledged us Clears all values in this submenu Endpoint on all PVCsViolations Displays the current state of the LCP negotiations Resets the Tx and Rx packet countersClears all values in this submenu Number of packets transmitted over this link Total number of Fecn bits received on this PVC Resets all sublink countersLocal address for each PVC as assigned by the carrier For Adtran internal use only Creates and configures packet endpointsTotal number of Becn bits received on this PVC Acts as the network side of the UNI interface Remote device does not support frame relay signalingOperates in NNI mode Acts as the user side of the UNI interface Displays the configuration for this packet endpoint Contains the Authentication parameters for this endpoint This turns on authentication debugging Username that the peer will use to authenticate the AtlasPassword that the peer will use to authenticate the Atlas This turns on LCP negotiation debugging Packet Manager Packet Endpnts Config Config Sdlc User-definable name for the Dlci Tate to a UTO for normal operation Allows configuration of parameters for each DlciThis Dlci disregards the status as reported from the switch Reports Active to all packet endpoints within Atlas Diagnostic Mode Disables backup switching Provides switching optionsForces a switch to backup Provides normal operation Displays the user-defined name for the Dlci Displays the name of the packet endpointDisplays the protocol running on the packet endpoint Displays the test mode for the PVC Shows the duration in seconds for the fixed-duration test Displays the total number of packet endpoints configured Displays the average round trip delay for the current testResets the counters Indicates data source Indicates data destination Displays the port number and name Indicates collection of IQ data for the target Dlci Within the given linkDisplays the Data Link Connection Identifier circuit number Sets the parameters for IQ statistics gathering Number of frames the port received for the interval or day Number of bytes the port received for the interval or day Number of PVC-signaling, full-status frames transmitted Time, in seconds, the signaling state has been downNumber of PVC-signaling, full-status frames received Number of frames discarded by the IQ unit Number of frames received with CRC errorsNumber of single PVC status frames received Number of frames received without proper flag termination Packet Manager Frame Relay IQ View IQ Statistics Sublink Number of DEs the PVC has received for the interval or day Number of CRs the PVC has received for the interval or day Maximum frame size the PVC received for the interval or day Number of lost frames on the PVC for the interval or dayMinimum frame size the PVC received for the interval or day Average frame size the PVC received for the interval or day Number of state changes for this PVC for the interval or day Router Router IP ARP Cache MAC Address Router IP ARP CacheRouter IP ARP Cache IP Address Adds a static route to the router Router IP ARP Cache Time Router IP ARP Cache Type Clears the Used menu and resets the value to zero Router IP Routes TTL Route address see the following, Far-End Address Dlci NumberRoute table This virtual circuit On this virtual circuitAre listened to No modification of the routing metric RIP advertisements are periodically transmitted Defines when RIP advertisements are transmittedDefines the secret used to advertise routes when using RIP Learned routes do not age Router IP Ping Specifies the number of pings to send. The maximum value is Ctrl + \ Ctrl + Shift + Transport layer protocol Received in errorHost Destination address was not a local address 550, and the Source-Route option processing was successful IP Statistics Name Description Number of Icmp Parameter Problem messages sent Having errors bad Icmp checksums, bad length, etcNumber of Icmp Parameter Problem messages received Clears the accumulated statistics Number of Icmp Timestamp request messages sent Number of Icmp Echo request messages sentNumber of Icmp Echo Reply messages sent Number of Icmp Timestamp Reply messages sent Total number of UDP datagrams delivered to UDP users Established or CLOSE-WAITExcluding those containing only retransmitted octets Destination port Router IP UDP Relay Router IP UDP Relay EnableEnables/disables the router to act as a relay agent Specifies the UDP port 1 to 65,535 in the UDP Port columns Dedicated Maps Displays the index number of the available maps Dedicated Maps CREATE/EDIT Maps Connects Port Specifies which days of the week the map is active T1 Trunk Conditioning Service TS0 Rate Defines ports to be used for this connection Answer Supervision Rx AB Tx AB Dedicated Maps FXO CREATE/EDIT Maps Connects TO/FROM Config Sets the DS0 rate to either 56 or 64 kbps Dedicated Maps Ussi CREATE/EDIT Maps Connects TO/FROM Config Dedicated Maps NXT1 Hssi and NXT1 HSSI/V.35 Modules DS0S Available Configures the port to use Flags or Ones as the idle code Legacy Data Option Module Receive Idle Code Voice Port This activator forces a link in/out of backup Circuit Status Menu Link is in error and waiting on backup Attempting to dial the backup linkWill retry backup dialing in num seconds Link is answering a backup endpoint Failed last manual or scheduled test No current test call on this dedicated dial backup circuitPassed last manual or scheduled test Dial Plan Dial Plan Network Term PORT/PEP Dial Plan Network Term OUT#ACCEPT Accept Number Dial Plan Network Term OUT#ACCEPT Treat Call AS Dial Plan Network Term Subst Templ ORIGINAL# Equipment. In this case, Atlas 550 is acting as the network Dial Plan User Term IN#ACCEPT SRC ID Primary accept number for the local exchange would be N$, IXC trunks are unavailable busy or in alarm. In this case,Primary endpoints are unavailable Secondary accept would be 1$ Dial Plan User Term Ifce Config Dial Plan User Term Subst Templ Local area code. Use for sending caller ID to the network Use extreme caution when forcing Collision Response Specifies the configuration parameters for the endpoint AT&T 4ESS Dial Plan T1/PRI Network Term PRI Ifce Config PRI Strip MSD Switched Digital Network AT&T SDN Contiguous channels from last to first Dial Plan T1/PRI Network Term RBSWould be used if available Send a progress message to the CPE and map busy tones From the network Dial Plan T1/PRI Network Term RBS Ifce Config RBSDial Plan T1/PRI Network Term RBS Ifce Config RBS First DS0 Loop Start Dial Plan T1/PRI Network Term RBS Ifce Config RBS did Digits ANI/DNIS Must define the trunk number Dial Plan T1/PRI Network Term RBS Ifce Config RBS Strip MSDDial Plan T1/PRI Network Term RBS Ifce Config RBS Source ID 272 ADTRAN, Inc Among the available DS0s on this interface Dial Plan T1/PRI User Term PRIWould be used if available Received Dial Plan T1/PRI User Term PRI Ifce Config PRI Strip MSD Dial Plan T1/PRI User Term PRI Ifce Config PRI Swap ANI/DNIS Dial Plan T1/PRI User Term RBS Dial Plan T1/PRI User Term RBS Ifce Config RBSDial Plan T1/PRI User Term RBS Ifce Config RBS First DS0 61200305L1-1F ADTRAN, Inc 277 Through this endpoint. This item is optional Dial Plan T1/PRI User Term RBS Ifce Config RBS Strip MSDDial Plan T1/PRI User Term RBS Ifce Config RBS Source ID Dial on Offhook number must be specific i.e., no wildcards Dial Plan T1/PRI User Term RBS Ifce Config RBS DS0 Selection Dial Plan E1/PRA Network Term PRA Ifce Config PRA First DS0 Dial Plan E1/PRA Network Term PRA Ifce Config PRA Source ID Dial Plan E1/PRA User Term PRA Dial Plan E1/PRA User Term PRA Ifce Config PRA Swap ANI/DNIS Phone numbers assigned to this BRI phone line Spid Number Dial Plan U-BRI User Term Dial Plan U-BRI User Term Ifce Config Strip MSD From the Network Pstn Caller ID number must be specific i.e., no wild cards Available Contiguous ports from last to first Dial Plan FXS User Term Ifce Config ANI to Caller ID Dial Plan FXO Network Term Ifce Config Number of Ports Dial Plan FXO Network Term Ifce Config Strip MSD DPT Dial Plan FXO User Term Ifce Config Direct Inward Dialing Dial Plan Octal E&M Module Dial Plan E&M User Term Dial Plan E&M User Term Ifce Config Signaling Method Dial Plan E&M User Term Ifce Config Source ID Specifies the number to dial on an outgoing call Dial Plan V35NX User Term Ifce Config Source ID Dial Plan Ussi User Term Ifce Config Ports Available Dial Plan Ussi User Term Ifce Config MIN DS0’S Defines the number dialed to originate a call Selects the time delay in seconds between redial attemptsFor User terminations, the number of calls is fixed at Defines the number of redials to attempt Dial Plan PKT Endpt User Term Ifce Config Call Party Number Backup Endpoint will originate the backup callBackup if an error is detected This only applies to originating endpoints Only by the Manual activator RED, Yellow, or Blue alarmsWhen network is out of alarm This is the time of day to enable dial backup How often test calls are to be made Date of the next scheduled test call Selects the appropriate Dlci for this dial plan entry Dial Plan PKT Voice Network Term Ifce Config did Prefix Dial Plan PKT Voice Network Term Ifce Config Strip MSD Dial Plan PKT Voice User Term Ifce Config Conflict Report Dial Plan PKT Voice User Term Ifce Config Strip MSD Detail Level Procedures DLP-Index Atlas 550 System Manual Connecting the Terminal or PC to the CONTROL/CRAFT Port Introduction DLP-001 Perform Steps Below in the Order Listed Logging in to the System DLP-002 61200305L1-1F ADTRAN, Inc 321 322 ADTRAN, Inc Setting IP Parameters for the Atlas Enter the appropriate Subnet Mask Enter the appropriate Default GatewayEnter the appropriate IP address Access to a PC or other computer connected to the LAN Verifying Communications Over AN IP LAN DLP-004 Atlas 550 System Manual DLP-004 Telnet to the Atlas 328 ADTRAN, Inc ADDING/REMOVING Users and Changing Password Security Levels VT100 terminal or PC with VT100 terminal emulation software DLP-005 Select level... If you want the user to Updating the Firmware Using Tftp DLP-006 Atlas 550 System Manual DLP-006 334 ADTRAN, Inc Updating the Firmware Using Xmodem DLP-007 Atlas 550 System Manual DLP-007 338 ADTRAN, Inc Saving the Current Configuration Using Tftp DLP-008 Respond with Y to confirm request Loading a Configuration Using Tftp DLP-009 Respond with Y to confirmation request Saving the Current Configuration Using Xmodem DLP-010 Loading a Configuration Using Xmodem Review the steps above for possible configuration errors DLP-011 Connecting the Atlas 550 to AN External Modem DLP-012 Atlas 550 System Manual DLP-012 350 ADTRAN, Inc Using the Adtran Utility Syslog with the Atlas Setting Up the Atlas 550 to use the Syslog Setting Up the Syslog Host Additional Syslog Features 354 ADTRAN, Inc Connecting the Alarm Contacts Alarm Relay Connector Pinout DLP-014 Atlas 550 System Manual DLP-014 358 ADTRAN, Inc Using the Alarm Connections and ACO Button DLP-015 Perform the Steps Below in the Order Listed Clearing the Alarm Relay Remotely 362 ADTRAN, Inc Configuration Guides CFG-6 Atlas 550 System Manual Dial Backup for Dedicated T1 Circuits Before You Begin Configuring the Dedicated T1 Data Link CFG-001 61200305L1-1F ADTRAN, Inc 367 368 ADTRAN, Inc Configuring the Dial Backup PRI 370 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 371 Configuring the Dial Backup Endpoint SLT field in the Dedicated MAP ORIGINATE/ANSWER MIN DS0S 376 ADTRAN, Inc System Event Logging Setting the Event LOG Category Atlas 550 System Manual System Event Logging Viewing the Events System Events System Controller Events Console Log String Category Console Log String Category Event Switchboard Events Console Log String CategorySystem Controller Events Nx 56/64 Events Console Log String Category Nx 56/64 Events T1 Events Console Log String Category T1 Events Ethernet Events Isdn Events Circuit Backup Events Modem Management Module Events Console Log String Category DP Outgoing Signaling EventsIsdn Cause Codes Isdn Cause Code Events Category Incompatibledest Major Interworkingunspec Code Location Cause Code LOG EntriesCause Code Log Entry Location Designations Isdn Layer 2 Lapd Message 390 ADTRAN, Inc VT100 Utility Adtran UtilitiesTelnet Utility Tftp Server Telnet Utility Telnet Menu Tree Connect Click on Session to open the Telnet sessionEstablishes the Telnet session Provides viewing alternatives for the terminal screen Provides Copy and Paste commandsEnds the Telnet session and closes the Telnet screen Echoes each character that you enter Opens the on-line help Provides on-line help for using the Adtran UtilitiesVT100 Utility Displays version and owner information Uploads and downloads files to and from an Atlas Opens VT100 terminal emulation sessionOpens a specified serial port for a VT100 session Selects the Xmodem file transfer protocol Redraws the screen Provides terminal screen commandsIdentical to the Telnet Edit Menu see Edit Menu on Identical to Telnet Colors Menu see Colors on Tftp Server Tftp Server Interface Menu Tree Terminates active transfers and closes the Tftp window Provides enable, disable, abort, and exit optionsTerminates a transfer that is in progress Provides print options Log Field Xmit meter provides a visual record of the transfer process MIB MIBs Supported by the Atlas MIB Compilation Order Traps Supported by the Atlas 404 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 405 MIB Variables Supported by the Atlas IpInAddrErrors IpDefaultTTLIpInHdrErrors IpForwarding IpForwDatagrams IpReasmTimeoutIcmpInErrors IpInUnknownProtos IcmpInRedirects IcmpInSrcQuenchsIcmpOutErrors IcmpInEchos TcpAttemptFails TcpEstabResetsTcpInSegs TcpCurrEstab 61200305L1-1F ADTRAN, Inc 411 Rfc1406.mib 6.1.2.1.10.18 61200305L1-1F ADTRAN, Inc 413 Rfc1315.mib 6.1.2.1.10.32 Adtran.mib 6.1.4.1.664 Ads1.mib 6.1.4.1.664.2.3 Atunit.mib 6.1.4.1.664.2.154.1.5 Atmod.mib 6.1.4.1.664.2.154.1.6 Atv35nx.mib 6.1.4.1.664.2.154.1.7 Atbri.mib 6.1.4.1.664.2.154.1.8 Att1.mib 6.1.4.1.664.2.154.1.9 61200305L1-1F ADTRAN, Inc 421 Atvoice.mib 6.1.4.1.664.2.154.1.10 Athssv35.mib 6.1.4.1.664.2.154.1.11 At550.mib 6.1.4.1.664.2.219 Atqbriu.mib 6.1.4.1.664.2.274 Fperform.mib 6.1.4.1.664.4.1 61200305L1-1F ADTRAN, Inc 425 426 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 427 428 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 429 430 ADTRAN, Inc