Dial Plan E1/PRA User Term PRA | ADTRAN 1200305L1 specs

ATLAS 550 System Manual	Section 4, User Interface Guide

DIAL PLAN (E1/PRA) > USER TERM (PRA)

Write security: 3; Read security: 5

This menu allows the user to define option parameters for ports which emulate a PRA connection.

DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA)

Write security: 3; Read security: 5

Specifies the configuration parameters for the endpoint.

DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > SWITCH TYPE

Write security: 3; Read security: 5

Defines the type of PRA switch that the ATLAS 550 emulates. If connected to another ATLAS 550, both need to be set to the same switch type. The following option is available:

•ETSI/DSS1

DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > FIRST DS0

Write security: 3; Read security: 5

Defines the first DS0 for this endpoint.The ATLAS 550 uses DS0s, starting with this selection, to send and receive calls to and from the network. The outgoing calls which are allowed or restricted over these DS0s are set by OUT#ACCEPT (see Dial Plan > Network Term > Out#Accept on page 254) and OUT#REJECT (see Dial Plan > Network Term > Out#Rej on page 256).

DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > NUMBER OF DS0S

Write security: 3; Read security: 5

Specifies the number of DS0s ATLAS 550 uses for this endpoint.

DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > STRIP MSD

Write security: 3; Read security: 5

Strips a selected quantity (choose from NONE, 1, 2, and 3) of the most significant digits (MSD) of a dialed number prior to being forwarded out of the port.

Example: A network port could be set to accept all calls beginning with 9 (9$), and then with STRIP MSD set to 1, all digits would be sent toward the network except the leading 9.

STRIP MSD does not affect CALL ACCEPT criteria. All of the digits (including the MSDs that are subsequently stripped) are used as accept criterion.

DIAL PLAN (E1/PRA) > USER TERM (PRA) > IFCE CONFIG (PRA) > NETWORK SPECIFIC FACILITY VOICE AND DATA

Write security: 3; Read security: 5

Enables the sending of appropriate information to the PSTN. Currently not supported for E1/PRA use.

61200305L1-1F

© 2002 ADTRAN, Inc.

283

Image 283

ADTRAN 1200305L1 system manual Dial Plan E1/PRA User Term PRA, Specifies the configuration parameters for the endpoint

Contents

Atlas To the Holder of the Manual Trademarks About this Manual Network Turnup ProcedureDetail Level Procedures Configuration Guides Revision History MIB Save These Important Safety Instructions Safety Instructions Affidavit Requirements for Connection to Digital Services ADTRAN, Inc Running H/F 1 doc title Running H/F 1 doc title ADTRAN, Inc REN FIC Usoc Running H/F 1 doc title ADTRAN, Inc ADTRAN, Inc Running H/F 1 doc title Limited Product Warranty Warranty and Customer Service Repair and Return Customer Service, Product Support Information, and TrainingPre-Sales Inquiries and Applications Support Post-Sale Support Installation and Maintenance SupportTraining System Description Contents Signaling Support Features and BenefitsConfiguration and Management Software Upgradeable PPP Switching Isdn Switch TypesSwitched Connection Maps Testing T1/PRI Network Interface Module P/N 1200307L1 Option Modules Dual Nx 56/64 Option Module P/N 1200311L1 E1/PRA Network Interface Module P/N 1200308L1Modem Management Network Module P/N 1200341L1 BRI DBU Network Interface Module P/N 1200327L1 Octal E&M Option Module P/N 1200313L1 Octal Ethernet Switch Option Module P/N 1200766L1Octal/Quad FXS Option Module P/N 1200309L1/1200328L1 Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Nx 56/64 BONDing Resource Module P/N 1200326L1 Channel Adpcm Resource Module P/N 1200752L1 System Description Atlas 550 System Manual Reviewing the Rear Panel Design At-A-Glance SpecificationsEngineering Guidelines Reviewing the Front Panel Design Tables Reviewing the Front Panel Design Equipment DimensionsPower Requirements ACO Switch Front Panel LEDs Craft Port Craft Port Feature Description Option Module LEDsACO Switch For these LEDs This color light Indicates that Power Module Test StatusModule Status Module Online AC System Reviewing the Rear Panel DesignDC System Control OUT Port Connector type RJ-48C Control in PinoutConnector type RJ-48C Control OUT Pinout Control in Port Ethernet Connection Alarm Relay ConnectionConnector type Usoc Alarm Relay Connector Pinout Name Description Shows the pinout for the External Alarm Relay connector External Alarm Relay Monitor ConnectionNetwork Interface Modules Test Interface T1/PRI Network Interface 15-pin Male D-connector Pinout Modem Management Network Module 6-pin Modular Jack Pinout E1/PRA Network Interface 15-pin Female D-connector Pinout FXS Pinout BRI DBU Network Module P/N 1200327L1Option Module Interfaces BRI Pinout 35 Winchester Pinout FXO PinoutPin PIN Signal Description DB-78 Connector Pinout System part number EIA-530 Connector Pinout RS-449/V.36 Connector Pinout EIA-530A Connector Pinout RS-232 Connector Pinout M Pinout Ccitt X.21/V.11 Connector Pinout T1/PRI Pinout Trunk Circuit Connections for Various E&M Signaling TypesQuad BRI U-Interface Option Module P/N 1200315L1 Trunk Circuit Connections Hssi SCSI-50 Connection Pinout PIN# + side PIN# side Quad BRI Isdn S/T Interface Option Module P/N 1200764L1NxT1 Hssi Option Module P/N 1200346L1 BRI Pinout S/T Interface HSSI/V.35 Connection Pinout PIN# + side PIN# side Hssi SCSI-50 Connection Pinout EIA-232 and V.35 Connection Pinouts Connector TypesHSSI/V.35 Connection Pinout T1 Network Connection Pinout Octal Ethernet Switch Option Module P/N 1200766L1 Switching Applications AT-A-GLANCE SpecificationsLists the specifications for the Atlas 550 system Specifications Application Feature TDM Applications IP Routing Specifications Application Feature Adpcm Specifications Application Feature Voice Compression Engineering Guidelines Atlas 550 System Manual Mounting Options Network Turnup ProcedureUnpack and Inspect the System Grounding Instructions Unpack and Inspect the System Contents of Adtran ShipmentsIntroduction Tools Required AC Powered Systems Supplying Power to the UnitGrounding Instructions Installing Network and Option Modules DC Powered SystemsMounting Options Shipping Contents Modem Management Network Module P/N 1200341L1 Quad Basic Rate Isdn U-Interface Option Module P/N 1200315L1 Dual Ussi Option Module System P/N 4200754Lx Octal/Quad FXO Option Module P/N 1200310L1/1200329L1 Ethernet Switch Option Module P/N 1200766L1 Network Turnup Procedure Atlas 550 System Manual Selecting the Appropriate Menu Security Levels User Interface Guide User Interface Guide Atlas 550 System Manual Atlas 550 System Manual User Interface Guide Terminal Menu Window Navigating the Terminal MenuMenu Path Left Pane To do this Press this key Alternate Menu View Window Pane Navigation Right Window Pane Notation Navigating using the Keyboard KeysThis notation Means that To do this Session Management Keystrokes Review and monitor system status for the Atlas Set up the operational configuration for the AtlasTerminal Menu and System Control Selecting the Appropriate Menu To do this Go to this menu Password Security LevelsSecurity Levels Menu Descriptions System Info Displays the boot ROM revision System Status Displays the port in which the event occurred Displays the source of the eventDisplays a description of the event Indicates whether the Ethernet network is 10 or 100BaseT Indicates the current status of the Ethernet port Failure condition Normal conditionNo Information Available User Interface Guide Atlas 550 System Manual Configures the statistics displayed under data tables Performs reset on Saturday night, 1200 AM Performs reset daily at 1200 AMDisplay for collected resource usage data Displays the usage data broken down by slots and ports System Config System Config Session Timeout System Config Ethernet Port MAC Address System Config Snmp Snmp Access Defines the destination for Snmp traps as follows Defines Snmp managers characteristics as followsEnables and disables Snmp trap transmission Specifies the IP address of the network manager System Config Snmp Traps Destination Community ESF System Config Snmp DS1 Total Perf Thresholds System Config Snmp DS1 Total Perf Thresholds Total ES Thrsh System Config Snmp SNMP/ASP Polling System Config Snmp SNMP/ASP Proxy System Config Syslog Setup License key System Config Bonding Config Txfa Timer System Config Alarm Relay Threshold System Utility System Utility Update Firmware Transfer Method Defines the type of module for each slot Indicates the status of the current updateIndicates the time of the previous update Indicates the slot number Indicates the status of the previous transfer Indicates the current status of the transfer Displays which slot and port is currently being tested Self-tests disrupt data flow Event description Index number of the logAtlas 550 slot number Atlas 550 port number Specifies the IP address to ping Clears the self-test log System Utility Ping Round Trip MAX Displays status from current Telnet client sessions System Utility Factory Default System Modules Modules Type Modules T1/PRI-1 Info Receiving remote alarm RAI on port Displays the assembly revision of the moduleDisplays the current T1 alarm status Indicates a loss of signal detected on port interface Modules T1/PRI-1 DS0 Status Modules T1/PRI-1 DS0 AlarmsModules T1/PRI-1 SIG Status Unavailable Second Line Errored SecondNot be obtained Controlled Slip Second Displays the port number Modules T1/PRI-1 Configuration LBO Modules T1/PRI-1 Test LOC LB Modules T1/PRI-1 Configuration Adlp Over FDLModules T1/PRI-1 Test Modules T1/PRI-1 Test PRT Modules T1/PRI-1 Test CLR Modules T1/PRI-1 Test Remote LBModules T1/PRI-1 Test Pattern Modules T1/PRI-1 Test QRSS/RLB Results Displays the E1 framer hardware revision Displays the current E1 alarm statusModules E1/PRA-1 Info Modules E1/PRA-1 PRT Modules E1/PRA-1 TS0 Alarms Modules E1/PRA-1 AlarmsModules E1/PRA-1 TS0 Status Modules E1/PRA-1 SIG Status Modules E1/PRA-1 Configuration TS16 MF Modules E1/PRA-1 Configuration NfasModules E1/PRA-1 Configuration CRC-4 Information Modules E1/PRA-1 TestModules E1/PRA-1 Test PRT Modules E1/PRA-1 Test LOC LB Modules E1/PRA-1 Test INJ Modules E1/PRA-1 Test PatternModules E1/PRA-1 Test Qrss Results Modules E1/PRA-1 Test CLR Displays the part number of the module Displays the assembly revisionDisplays the serial number of the module Displays the results of the last Detect Dial Tone test Provides testing capabilities for the internal modem Indicates the current status of a particular Bonding session Bonding Modules DBU Bonding Configuration TXADD01 Timer Far-end block errors Near-end block errorsDisplays the port number Modules T1/PRI-2/4 Info Part Number Modules T1/PRI-2/4 Info Modules T1/PRI-2/4 DS0 Status Modules T1/PRI-2/4 Alarm StatusModules T1/PRI-2/4 Alarm Status PRT Modules T1/PRI-2/4 Info PLL Status Modules T1/PRI-2/4 DS0 Alarms Modules T1/PRI-2/4 Performance 15MIN Modules T1/PRI-2/4 SIG StatusModules T1/PRI-2/4 Performance 24HR Modules T1/PRI-2/4 Configuration LBO Modules T1/PRI-2/4 Test LOC LB Modules T1/PRI-2/4 Configuration Adlp Over FDLModules T1/PRI-2/4 Test Modules T1/PRI-2/4 Test PRT Modules T1/PRI-2/4 Test CLR Modules T1/PRI-2/4 Test Remote LBModules T1/PRI-2/4 Test Pattern Modules T1/PRI-2/4 Test QRSS/RLB Results Modules V35NX-2 Info Following signals are monitored these options are read-only Clears inband statistic results Displays the Phase Lock Loop PLL and Fifo statusModules V35NX-2 PLL/FIFO Modules V35NX-2 PLL/FIFO Port Transmit data Fifo empty Modules V35NX-2 PLL/FIFO PLL/FIFOReceive data Fifo empty Receive data Fifo full Follows Off Test Modules V35NX-2 Dial Dial Modules V35NX-2 Dial ModeModules V35NX-2 Dial Modules V35NX-2 Dial PRT Code Modules V35NX-2 TestModules V35NX-2 Test 511 Result Loopback toward the network Modules USSI-2 Info Modules V35NX-2 Test CLR Modules USSI-2 Data Rate Modules USSI-2 DTE Status DTE Status Displays the data rate of the selected port Modules USSI-2 PLL/FIFOProvides information on the inband channel statistics Modules USSI-2 PLL/FIFO PLL/FIFO Modules USSI-2 PLL/FIFO Port Modules USSI-2 Configuration CTS Modules USSI-2 Dial Dial Modules USSI-2 Dial ModeModules USSI-2 Dial Modules USSI-2 Dial PRT Modules USSI-2 Test 511 Result Modules USSI-2 Test PortModules USSI-2 Test Inject Modules USSI-2 DTE Interface Modules USSI-2 Test CLRModules USSI-2 DTE Interface PRT Modules U-BRI-4 Info Modules U-BRI-4 AlarmsModules U-BRI-4 Alarms PRT Detected with the endpoint or a cabling problem Modules U-BRI-4 Test PRT Modules U-BRI-4 Test Loops the entire physical interface Modules ST-BRI-4 AlarmsModules ST-BRI-4 Alarms PRT Modules ST-BRI-4 Info Modules ST-BRI-4 Alarms Alarms Modules ST-BRI-4 Test PRT Modules ST-BRI-4 TestOption Module Displays the status of each of the FXS ports Modules FXS-4/8 InfoModules FXS-4/8 Status Displays the processor ID of the selected module Modules FXS-4/8 Status RX Abcd Modules FXS-4/8 Status PRT Modules FXS-4/8 Test Test 2W Modules FXS-4/8 Status TX AbcdModules FXS-4/8 Test Modules FXS-4/8 Test Port Modules FXS-4/8 Test 1KHZ Tone Modules FXS-4/8 ConfigModules FXS-4/8 Config PRT Modules FXS-4/8 Test TX Abcd Modules FXS-4/8 Config TX Gain Modules FXS-4/8 Config RX GainModules FXO-4/8 Info Modules FXO-4/8 Status PRT Modules FXO-4/8 StatusDisplays the status of each of the FXO ports Modules FXO-4/8 Test Port Modules FXO-4/8 Status RX AbcdModules FXO-4/8 Status TX Abcd Modules FXO-4/8 Test Modules FXO-4/8 Test 1KHZ Tone Modules FXO-4/8 ConfigModules FXO-4/8 Config PRT Modules FXO-4/8 Test TX Abcd Modules FXO-4/8 Config TX Gain Modules FXO-4/8 Config RX Gain Modules E&M-8 Status PRT Modules E&M-8 StatusDisplays the status of each of the eight E&M ports Modules E&M-8 Test Port Modules E&M-8 Status RX AbcdModules E&M-8 Status TX Abcd Modules E&M-8 Test Normal operation Modules E&M-8 ConfigModules E&M-8 Config VF Ifce Modules E&M-8 Test 1KHZ Tone Modules E&M-8 Config RX Gain Data terminal ready from DTE Modules LEGACY-4 Port Stats ERR FR Modules NXT1HSSI T1 Menus Displays the firmware revision of the installed moduleModules Menu NXT1 Hssi and NXT1 HSSI/V.35 Option Modules Modules NXT1 Hssi Info Indicates a loss of signal detected on the port interface Modules NXT1HSSI Performance 15MIN Modules NXT1HSSI Test Port Modules NXT1HSSI TestModules NXT1HSSI Test LOC LB Modules NXT1HSSI Imux Menus Status Port Modules NXT1HSSI Imux Menus ConfigModules NXT1HSSI Imux Menus Modules NXT1HSSI Imux Menus Status Modules NXT1HSSI Hssi Menus Status Modules NXT1HSSI Imux Menus Config PortModules NXT1HSSI Imux Menus Config GRP Assoc Modules NXT1HSSI Hssi Menus Following loopback status messages may display Hssi Interface Loopback Test Diagram Modules NXT1HSSI Hssi Menus Status TA Modules NXT1HSSI Hssi Menus Status CAModules NXT1HSSI Hssi Menus Status LA and LB Modules NXT1HSSI Hssi Menus Status LC Modules NXT1HSSI Hssi Menus Config CTS Modules NXT1HSSI Hssi Menus ConfigModules NXT1HSSI Hssi Menus Config Port Name Modules NXT1HSSI Hssi Menus Config TX CLK Modules NXT1HSSI Hssi Menus Test Port Modules NXT1HSSI Hssi Menus Config DCDModules NXT1HSSI Hssi Menus Config CA Modules NXT1HSSI Hssi Menus Test Modules ENET-8 Status Port Modules NXT1HSSI Hssi Menus Test Remote Lpbk HssiModules ENET-8 Info Modules ENET-8 Status Modules VCOM-X Info This resource is currently in use This resource was reinitialized after excessive errorsPrinciple applies to the VCOM-8, 24, and 32 Option Modules This resource is currently changing state Proprietary Netcoder compression 6.4 kbps bandwidth Ccitt G.723.1 compression 6.3 kbps bandwidth Session Is between protocol statesDual-tone, multi-frequency Dtmf digit received Voice status until the FAX protocol is established Any calls routed to it Marking a device as Disabled prevents the Atlas 550 from Modules VCOM-X Statistics Atlas Drop Modules VCOM-X Statistics Atlas Frms Modules ADPCM-32 Info Displays the status of each of the packet voice resources Modules ADPCM-32 StatusModules ADPCM-32 Status Device Modules ADPCM-32 Status Status Modules ADPCM-32 Config Configure ADPCM-32 Devices Modules ADPCM-32 Config Modules ADPCM-32 Statistics Atlas Frms Modules ADPCM-32 Statistics ADPCM-32 Frms Modules ADPCM-32 Statistics Atlas DropModules ADPCM-32 Statistics ADPCM-32 Drop Displays the current status of the Bonding session Displays the board revision of the installed moduleModules Bonding Info Modules Bonding Status Modules Bonding Status Bonded EP Modules Bonding Configuration Txdeq Timer SEC Packet Manager Signaling using Group of Four Interface NNI modeSignaling using ITU-T Q.933-A Signaling using Ansi T1.617-D But the peer has not acknowledged us Sent configuration requestEnabled, occurs now Is waiting for an acknowledge Violations Endpoint on all PVCsClears all values in this submenu Number of packets transmitted over this link Resets the Tx and Rx packet countersClears all values in this submenu Displays the current state of the LCP negotiations Local address for each PVC as assigned by the carrier Resets all sublink countersTotal number of Fecn bits received on this PVC Total number of Becn bits received on this PVC Creates and configures packet endpointsFor Adtran internal use only Acts as the user side of the UNI interface Remote device does not support frame relay signalingOperates in NNI mode Acts as the network side of the UNI interface Contains the Authentication parameters for this endpoint Displays the configuration for this packet endpoint This turns on LCP negotiation debugging Username that the peer will use to authenticate the AtlasPassword that the peer will use to authenticate the Atlas This turns on authentication debugging Packet Manager Packet Endpnts Config Config Sdlc User-definable name for the Dlci Reports Active to all packet endpoints within Atlas Allows configuration of parameters for each DlciThis Dlci disregards the status as reported from the switch Tate to a UTO for normal operation Diagnostic Mode Provides normal operation Provides switching optionsForces a switch to backup Disables backup switching Displays the protocol running on the packet endpoint Displays the name of the packet endpointDisplays the user-defined name for the Dlci Shows the duration in seconds for the fixed-duration test Displays the test mode for the PVC Resets the counters Displays the average round trip delay for the current testDisplays the total number of packet endpoints configured Indicates data destination Indicates data source Displays the port number and name Sets the parameters for IQ statistics gathering Within the given linkDisplays the Data Link Connection Identifier circuit number Indicates collection of IQ data for the target Dlci Number of bytes the port received for the interval or day Number of frames the port received for the interval or day Number of PVC-signaling, full-status frames received Time, in seconds, the signaling state has been downNumber of PVC-signaling, full-status frames transmitted Number of frames received without proper flag termination Number of frames received with CRC errorsNumber of single PVC status frames received Number of frames discarded by the IQ unit Packet Manager Frame Relay IQ View IQ Statistics Sublink Number of CRs the PVC has received for the interval or day Number of DEs the PVC has received for the interval or day Average frame size the PVC received for the interval or day Number of lost frames on the PVC for the interval or dayMinimum frame size the PVC received for the interval or day Maximum frame size the PVC received for the interval or day Number of state changes for this PVC for the interval or day Router Adds a static route to the router Router IP ARP CacheRouter IP ARP Cache IP Address Router IP ARP Cache MAC Address Router IP ARP Cache Type Router IP ARP Cache Time Router IP Routes TTL Clears the Used menu and resets the value to zero Route table Dlci NumberRoute address see the following, Far-End Address No modification of the routing metric On this virtual circuitAre listened to This virtual circuit Learned routes do not age Defines when RIP advertisements are transmittedDefines the secret used to advertise routes when using RIP RIP advertisements are periodically transmitted Specifies the number of pings to send. The maximum value is Router IP Ping Ctrl + \ Ctrl + Shift + Destination address was not a local address Received in errorHost Transport layer protocol IP Statistics Name Description 550, and the Source-Route option processing was successful Clears the accumulated statistics Having errors bad Icmp checksums, bad length, etcNumber of Icmp Parameter Problem messages received Number of Icmp Parameter Problem messages sent Number of Icmp Timestamp Reply messages sent Number of Icmp Echo request messages sentNumber of Icmp Echo Reply messages sent Number of Icmp Timestamp request messages sent Destination port Established or CLOSE-WAITExcluding those containing only retransmitted octets Total number of UDP datagrams delivered to UDP users Specifies the UDP port 1 to 65,535 in the UDP Port columns Router IP UDP Relay EnableEnables/disables the router to act as a relay agent Router IP UDP Relay Dedicated Maps Displays the index number of the available maps Dedicated Maps CREATE/EDIT Maps Connects Port Specifies which days of the week the map is active T1 Trunk Conditioning Service TS0 Rate Defines ports to be used for this connection Answer Supervision Rx AB Tx AB Dedicated Maps FXO CREATE/EDIT Maps Connects TO/FROM Config Sets the DS0 rate to either 56 or 64 kbps Dedicated Maps Ussi CREATE/EDIT Maps Connects TO/FROM Config Dedicated Maps NXT1 Hssi and NXT1 HSSI/V.35 Modules DS0S Available Legacy Data Option Module Configures the port to use Flags or Ones as the idle code Receive Idle Code Voice Port Circuit Status Menu This activator forces a link in/out of backup Link is answering a backup endpoint Attempting to dial the backup linkWill retry backup dialing in num seconds Link is in error and waiting on backup Passed last manual or scheduled test No current test call on this dedicated dial backup circuitFailed last manual or scheduled test Dial Plan Dial Plan Network Term PORT/PEP Dial Plan Network Term OUT#ACCEPT Accept Number Dial Plan Network Term OUT#ACCEPT Treat Call AS Dial Plan Network Term Subst Templ ORIGINAL# Equipment. In this case, Atlas 550 is acting as the network Dial Plan User Term IN#ACCEPT SRC ID Secondary accept would be 1$ IXC trunks are unavailable busy or in alarm. In this case,Primary endpoints are unavailable Primary accept number for the local exchange would be N$, Dial Plan User Term Ifce Config Dial Plan User Term Subst Templ Local area code. Use for sending caller ID to the network Use extreme caution when forcing Collision Response AT&T 4ESS Specifies the configuration parameters for the endpoint Dial Plan T1/PRI Network Term PRI Ifce Config PRI Strip MSD AT&T SDN Switched Digital Network Send a progress message to the CPE and map busy tones Dial Plan T1/PRI Network Term RBSWould be used if available Contiguous channels from last to first Loop Start Dial Plan T1/PRI Network Term RBS Ifce Config RBSDial Plan T1/PRI Network Term RBS Ifce Config RBS First DS0 From the network ANI/DNIS Dial Plan T1/PRI Network Term RBS Ifce Config RBS did Digits Dial Plan T1/PRI Network Term RBS Ifce Config RBS Source ID Dial Plan T1/PRI Network Term RBS Ifce Config RBS Strip MSDMust define the trunk number 272 ADTRAN, Inc Received Dial Plan T1/PRI User Term PRIWould be used if available Among the available DS0s on this interface Dial Plan T1/PRI User Term PRI Ifce Config PRI Strip MSD Dial Plan T1/PRI User Term PRI Ifce Config PRI Swap ANI/DNIS Dial Plan T1/PRI User Term RBS Ifce Config RBS First DS0 Dial Plan T1/PRI User Term RBS Ifce Config RBSDial Plan T1/PRI User Term RBS 61200305L1-1F ADTRAN, Inc 277 Dial Plan T1/PRI User Term RBS Ifce Config RBS Source ID Dial Plan T1/PRI User Term RBS Ifce Config RBS Strip MSDThrough this endpoint. This item is optional Dial on Offhook number must be specific i.e., no wildcards Dial Plan T1/PRI User Term RBS Ifce Config RBS DS0 Selection Dial Plan E1/PRA Network Term PRA Ifce Config PRA First DS0 Dial Plan E1/PRA Network Term PRA Ifce Config PRA Source ID Dial Plan E1/PRA User Term PRA Dial Plan E1/PRA User Term PRA Ifce Config PRA Swap ANI/DNIS Phone numbers assigned to this BRI phone line Spid Number Dial Plan U-BRI User Term Dial Plan U-BRI User Term Ifce Config Strip MSD From the Network Pstn Caller ID number must be specific i.e., no wild cards Contiguous ports from last to first Available Dial Plan FXS User Term Ifce Config ANI to Caller ID Dial Plan FXO Network Term Ifce Config Number of Ports Dial Plan FXO Network Term Ifce Config Strip MSD DPT Dial Plan FXO User Term Ifce Config Direct Inward Dialing Dial Plan Octal E&M Module Dial Plan E&M User Term Dial Plan E&M User Term Ifce Config Signaling Method Dial Plan E&M User Term Ifce Config Source ID Specifies the number to dial on an outgoing call Dial Plan V35NX User Term Ifce Config Source ID Dial Plan Ussi User Term Ifce Config Ports Available Dial Plan Ussi User Term Ifce Config MIN DS0’S For User terminations, the number of calls is fixed at Selects the time delay in seconds between redial attemptsDefines the number dialed to originate a call Defines the number of redials to attempt Dial Plan PKT Endpt User Term Ifce Config Call Party Number This only applies to originating endpoints Endpoint will originate the backup callBackup if an error is detected Backup When network is out of alarm RED, Yellow, or Blue alarmsOnly by the Manual activator How often test calls are to be made This is the time of day to enable dial backup Selects the appropriate Dlci for this dial plan entry Date of the next scheduled test call Dial Plan PKT Voice Network Term Ifce Config did Prefix Dial Plan PKT Voice Network Term Ifce Config Strip MSD Dial Plan PKT Voice User Term Ifce Config Conflict Report Dial Plan PKT Voice User Term Ifce Config Strip MSD Detail Level Procedures DLP-Index Atlas 550 System Manual Introduction Connecting the Terminal or PC to the CONTROL/CRAFT Port Perform Steps Below in the Order Listed DLP-001 Logging in to the System DLP-002 61200305L1-1F ADTRAN, Inc 321 322 ADTRAN, Inc Setting IP Parameters for the Atlas Enter the appropriate IP address Enter the appropriate Default GatewayEnter the appropriate Subnet Mask Verifying Communications Over AN IP LAN Access to a PC or other computer connected to the LAN DLP-004 Atlas 550 System Manual DLP-004 Telnet to the Atlas 328 ADTRAN, Inc VT100 terminal or PC with VT100 terminal emulation software ADDING/REMOVING Users and Changing Password Security Levels Select level... If you want the user to DLP-005 Updating the Firmware Using Tftp DLP-006 Atlas 550 System Manual DLP-006 334 ADTRAN, Inc Updating the Firmware Using Xmodem DLP-007 Atlas 550 System Manual DLP-007 338 ADTRAN, Inc Saving the Current Configuration Using Tftp Respond with Y to confirm request DLP-008 Loading a Configuration Using Tftp Respond with Y to confirmation request DLP-009 Saving the Current Configuration Using Xmodem DLP-010 Loading a Configuration Using Xmodem DLP-011 Review the steps above for possible configuration errors Connecting the Atlas 550 to AN External Modem DLP-012 Atlas 550 System Manual DLP-012 350 ADTRAN, Inc Using the Adtran Utility Syslog with the Atlas Setting Up the Syslog Host Setting Up the Atlas 550 to use the Syslog Additional Syslog Features 354 ADTRAN, Inc Connecting the Alarm Contacts DLP-014 Alarm Relay Connector Pinout Atlas 550 System Manual DLP-014 358 ADTRAN, Inc Using the Alarm Connections and ACO Button Perform the Steps Below in the Order Listed DLP-015 Clearing the Alarm Relay Remotely 362 ADTRAN, Inc Configuration Guides CFG-6 Atlas 550 System Manual Before You Begin Dial Backup for Dedicated T1 Circuits CFG-001 Configuring the Dedicated T1 Data Link 61200305L1-1F ADTRAN, Inc 367 368 ADTRAN, Inc Configuring the Dial Backup PRI 370 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 371 Configuring the Dial Backup Endpoint SLT field in the Dedicated MAP ORIGINATE/ANSWER MIN DS0S 376 ADTRAN, Inc System Event Logging Setting the Event LOG Category Atlas 550 System Manual System Event Logging Viewing the Events System Controller Events Console Log String Category System Events Nx 56/64 Events Console Log String Category Switchboard Events Console Log String CategorySystem Controller Events Console Log String Category Event T1 Events Console Log String Category Nx 56/64 Events Ethernet Events T1 Events Isdn Events Circuit Backup Events Isdn Cause Code Events Category DP Outgoing Signaling EventsIsdn Cause Codes Modem Management Module Events Console Log String Category Incompatibledest Major Interworkingunspec Isdn Layer 2 Lapd Message Cause Code LOG EntriesCause Code Log Entry Location Designations Code Location 390 ADTRAN, Inc Tftp Server Adtran UtilitiesTelnet Utility VT100 Utility Telnet Menu Tree Telnet Utility Establishes the Telnet session Click on Session to open the Telnet sessionConnect Echoes each character that you enter Provides Copy and Paste commandsEnds the Telnet session and closes the Telnet screen Provides viewing alternatives for the terminal screen Displays version and owner information Provides on-line help for using the Adtran UtilitiesVT100 Utility Opens the on-line help Selects the Xmodem file transfer protocol Opens VT100 terminal emulation sessionOpens a specified serial port for a VT100 session Uploads and downloads files to and from an Atlas Identical to Telnet Colors Menu see Colors on Provides terminal screen commandsIdentical to the Telnet Edit Menu see Edit Menu on Redraws the screen Tftp Server Interface Menu Tree Tftp Server Provides print options Provides enable, disable, abort, and exit optionsTerminates a transfer that is in progress Terminates active transfers and closes the Tftp window Xmit meter provides a visual record of the transfer process Log Field MIB MIBs Supported by the Atlas Traps Supported by the Atlas MIB Compilation Order 404 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 405 MIB Variables Supported by the Atlas IpForwarding IpDefaultTTLIpInHdrErrors IpInAddrErrors IpInUnknownProtos IpReasmTimeoutIcmpInErrors IpForwDatagrams IcmpInEchos IcmpInSrcQuenchsIcmpOutErrors IcmpInRedirects TcpCurrEstab TcpEstabResetsTcpInSegs TcpAttemptFails 61200305L1-1F ADTRAN, Inc 411 Rfc1406.mib 6.1.2.1.10.18 61200305L1-1F ADTRAN, Inc 413 Rfc1315.mib 6.1.2.1.10.32 Adtran.mib 6.1.4.1.664 Ads1.mib 6.1.4.1.664.2.3 Atunit.mib 6.1.4.1.664.2.154.1.5 Atv35nx.mib 6.1.4.1.664.2.154.1.7 Atmod.mib 6.1.4.1.664.2.154.1.6 Atbri.mib 6.1.4.1.664.2.154.1.8 Att1.mib 6.1.4.1.664.2.154.1.9 61200305L1-1F ADTRAN, Inc 421 Athssv35.mib 6.1.4.1.664.2.154.1.11 Atvoice.mib 6.1.4.1.664.2.154.1.10 At550.mib 6.1.4.1.664.2.219 Fperform.mib 6.1.4.1.664.4.1 Atqbriu.mib 6.1.4.1.664.2.274 61200305L1-1F ADTRAN, Inc 425 426 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 427 428 ADTRAN, Inc 61200305L1-1F ADTRAN, Inc 429 430 ADTRAN, Inc