Sanyo DSR-5009P Installation and Connections, Basic connections DSR-5016P, RS-232C Pin locations

3INSTALLATION AND CONNECTIONS

This section describes how to connect the digital video recorder to video cameras and other devices. Be sure to read the instruction manuals for each connected device.

zImproper connections may result in malfunction or smoke emission.

zA separate power supply is required for operation of each camera.

zManage power for all expansion units with a single power source. Otherwise, data may be lost.

Basic connections

DSR-5016P

Only nine cameras can be connected to the DSR-5009P.

The following diagram shows the connections for cameras, monitors, a microphone, a PC and a system controller.

Cameras	Monitor		Monitor 2	Microphone
(sold separately)
1 - 16	(sold separately)		(sold separately)	(commercially-
				* If monitor 2 is not synchronized available)
	01	02		with the connected cameras,
				vertical picture instability may
	03	04		occur upon the switching of
				camera video.

						Video input					Video input
						terminal					terminal
							*3				*4
								MAIN	MON2	S-VIDEO	1-AUDIO-2	AUDIO OUT		MIC IN
					SCSI						IN																			AC IN
						MONITOR OUT									ALARM IN
1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
															C	1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16

IN

OUT				USB
ALL
RESET	1	2	3	4

2ND

C

NON

W

AR

C LEXT

CHIVE

RS-485

RS-485/422

REMOTE

L OCK TIALARALARM REARNING

OCK

MER

M

C

O

F

O

LAN

RS-485

A SANYO SSP B

RS-232C

SENSOR

A B

INOUT

IN OUTRESET

UT

UTULL FULL

TERMINATE

ALARM OUT

C R1 R2

C

OFF ON

EXCEPT SANYO SSP

EXTERNAL STRAGE UNIT

1 - 4
HDD expansion unit	PC
(sold separately)	(commercially-available)

	DO NOT	CONNECT TO PHONE LINE				CONTROL
				The RS-485 connector is
				connected to A or B according to
*1				the type of cable.
			*2
					System controller
					(sold separately)

120 V – 240 V AC

(50/60 Hz)

*1 Wrap the LAN cable once around the core clamp (large) before attaching it.

*2 Wrap the RS-485 cable twice around the core clamp (small) before attaching it.

*3 Wrap the Main Monitor output cable once around the core clamp (large) before attaching it. *4 Wrap the S-VIDEO output cable once around the core clamp (small) before attaching it.

Connecting the RS-232C terminal

The RS-232C terminal is used to connect to a PC or a phone line for use with a modem. Perform the settings in the <RS- 232C/RS-485 SET> screen. (JP.115)

RS-232C Pin locations

		1	2	3	4	5
		6	7		8	9
Pin	Signal	Operation					Signal direction
number
1	DCD	Carrier Detect					From PC to digital video
							recorder
2	RXD	Receive Data					From PC to digital video
							recorder

Pin	Signal	Operation	Signal direction
number
3	TXD	Transmit Data	From digital video
			recorder to PC
4	DTR	–	From digital video
			recorder to PC
5	GND	Ground	–
6	DSR	–	From PC to digital video
			recorder
7	RTS	Request to	From digital video
		Send	recorder to PC
8	CTS	Clear to Send	From PC to digital video
			recorder
9	RI	Ring Indicator	From PC to digital video
			recorder

English 13