![](/images/backgrounds/275910/275910-267213x1.png)
Removal and Installation Procedures
|
|
|
|
|
| Is |
|
|
|
|
|
|
| ||
Use this procedure to |
|
| the PRINCIPAL | No |
|
|
|
|
|
| |||||
|
|
| Turn on the PRINCIPAL |
| |||||||||||
troubleshoot the power |
|
|
| POWER SWITCH in the |
|
| |||||||||
|
|
|
|
|
| ||||||||||
|
|
|
|
| POWER SWITCH. |
| |||||||||
supply module. |
|
|
|
| ON position? |
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
| Yes |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Does |
|
| ||
Is |
|
|
|
|
|
| |||||||||
No | Turn off the PRINCIPAL POWER |
|
|
| Yes | ||||||||||
line fuse |
|
| SWITCH. Replace the fuse. Turn |
|
|
| the fuse blow |
|
| ||||||
|
|
|
|
|
|
| |||||||||
ok? |
|
| on the principal power switch. |
|
|
| again? |
|
| ||||||
| Yes |
|
|
|
|
|
|
|
|
|
| No |
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Turn off the PRINCIPAL POWER SWITCH and remove the cover using the Cabinet removal procedure. Check all the
cables coming out of the power supply module and the cabling between modules. Be sure every cable is attached securely.
Turn off the PRINCIPAL POWER
SWITCH. Remove the generator cabinet
using the cabinet removal procedure. No Check the cables from the A11
Connector board. Disconnect the cables at J1 and J2 on the power supply module.
Press the ON/STBY button. Check these power supply voltages on J3 on the A10 Connector board:
+5 V"3%,
Turn on
the PRINCIPAL POWER
SWITCH. Can you hear |
|
| No |
| |||||
|
|
|
|
|
|
|
| ||
the tick of relay actuator |
|
|
|
|
|
|
|
| |
in the power supply |
|
|
|
|
|
|
|
| |
module? |
|
|
|
|
|
|
|
| |
| Yes |
|
|
|
| Are the |
| ||
|
|
|
|
|
| ||||
|
|
|
|
|
|
| |||
|
|
|
|
|
| voltages on the |
| ||
Press | Yes |
|
| A11 Connector board | No | ||||
the ON/STBY button. |
| TP030 : +5 V, TP010 : +12 V | |||||||
|
|
|
| ||||||
Does the generator |
|
|
| TP030 : |
| ||||
power on? |
|
|
|
| on page |
| |||
|
|
|
|
|
|
| Yes |
| |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Fix the power problem. |
|
| |
|
|
|
|
|
|
|
|
|
|
Are | No | |
the voltages | ||
| ||
ok? |
|
Yes
The power supply module is ok.
Perform isolation troubleshooting for the modules on the bottom of the generator.
Replace the power supply module (page
Figure
AWG710 Service Manual |