Maintenance | Texas Instruments MATRIX 3000, DW30 specs

Section 4

Maintenance

4.1Warnings and Safety Guidelines

The projector is an international regulatory agency approved product designed for safe and reliable operation. It is important to acknowledge the following precautions while operating the projector to assure complete safety at all times.

WARNING

Always remove the lens when shipping the

projector.

WARNING

NEVER look directly into the projector lens.

The high brightness of this projector could cause permanent eye damage.

WARNING

For protection from ultraviolet radiation,

keep all projector shielding intact during operation.

WARNING

Installation should be performed by qualified

personnel.

Labels and Markings f Observe and follow all warnings and instructions marked on the projector.

The exclamation point within the equilateral triangle alerts the user to important operating and maintenance (servicing) instructions in the literature accompanying the projector.

The lightning flash and arrowhead symbol within the equilateral triangle alerts the user to un-insulated “dangerous voltage” within the projector’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

Instructions f Read all operating instructions prior to using the projector.

013-100149-02 Rev. 1 (01/07)

Christie DS+60/DW3K/Matrix 3000 User’s Manual 4-1

Image 98

Texas Instruments MATRIX 3000, DW30 user manual Maintenance

Contents

+ 6 0 / D W 3 0 / M a t r i x 3 0 0 E r ’ s M a n u a l Table of Contents Page Projector Overview Key featuresIntroduction Powering on For more information see 3.7 The Lamp Menu Components How the Projector Works Purchase Record and Servicing Purchase Record Position the Projector Installation & SetupInstall a Projection Lens Connect a Source Turn the Projector on Perform Auto Setup on the current sourceConnect the Line Cord Select a Source Installation Considerations Rear screen installations Screen size Service and support product downloads Projector Position Throw distance Mounting Vertical and horizontal position Lens Offsets for DS+60 and Matrix 3000 SXGA+ Examples of Vertical Offset Lens Vertical Offsets Examples of Horizontal Offset Lens Horizontal Offsets Adjusting projector height Folded Optics Connecting Sources 10. Input Panel 11. Connecting RGB and Sync Interface Installed at InputOptional Inputs IR Remote f Connecting RS-232Connecting RS-422 15. Connecting RS422 Ethernet Communications Connecting Multiple Projectors 19. Ethernet Network All Ports System Integration Gpio ConnectorCommunicating to Power Connection 22. AC Line Cord Connection Exterior OperationAbout the Projector Lens Mount Adjustable FeetAC receptacle Projection Lenses Front & Rear IR Sensors Using the Remote or Built-In KeypadLamp Access Doors IR Remote Test Keypad Commands fPower ON/OFF Auto Input No function Gamma ContrastBrightness Menu Function Key ShutterPress and hold Shutter Projector Enter Arrow Keys Remote for the key to work Navigating the MenusLaser Other Controls Time-outsGlobal Icon Example of Pull-Down List To move the cursor forward or Or a Channel? Using Inputs and ChannelsDo I Select an Input f List unless a parameter for the channel has been changed ChannelChannel is highlighted upon Display the Channel Setup What Channels Deleting Channels Channels. See Copying or Deleting a Channel belowCopying or Channel Edit Step View, turn off the on-screen display by pressing OSD Adjusting the ImageBefore You Begin f Use Auto Setup Auto Refer to Using Slidebars Other Controls earlier in this Resize Presets Rev 01/07 Christie DS+60/DW30/Matrix 3000 User’s Manual Vertical Stretch Pixel PhaseSize Pixel Track Position Advanced Size and Position Submenu Blanking of a PIP Image Filter Detail Video Options Submenu Noise ReductionColor Space Overpowering and unrealistic Input Levels Submenu Page See .14. Adjusting Input Levels Using the Peak Detector Advanced Image Settings Submenu Page Simulation 3D Submenu of Advanced Image Settings Adjusting System Parameters and Advanced Controls Menu Preferences Submenu Network Routing System Configuration f Settings in the CommunicationsBaud Rates Ethernet Settings Submenu 17. Using the Network Routing Option ArtNet Interface Settings Submenu Backlight ExampleBroadcast Key Front IR / Back IR Geometry and Color submenu Wired KeypadSystem Configuration Test Pattern Keystone Edge Blending Submenu Color Adjustments by X/Y, and Color Saturation SubmenusBrightness Uniformity Submenu Any time in the Advanced Image Settings 19. Color Gamut Choices 21. CIE 1931 Chromaticity Diagram Odd Pixel Adjustment System Configuration Test PatternColor Enable Test Pattern Grey Level Color Wheel Calibration Submenu Color Wheel Calibration submenu Level Value Peak DetectorLevel Detector Aspect Ratio Overlay Working with PIP or Seamless Switching Signal Type Description Input Location Swap Main and PIP Image PIP EnablePIP Image Settings Submenu PIP Size and Position Submenu PIP Border Color SwitchingPIP Border Width Working with Seamless f Menu Modes and auto-switchingLamp Numbers Select Main ImagePage 24. The Lamp Menu Operation Projectors Using MultipleConnecting Multiple Projectors for full routing details Multiple Screens Color Adjustment Procedure ‰ Set Select Color Adjustment to Max Drives 26. Copy X/Y Values into All Projectors Using the Color Saturation Menu for Color Matching Uniformity General Setup Adjust Color level of red/green/blue in Eight Zones Adjust Light Output in 8 Zones 28. Match Zones to Center Color Temperature How Are Blends Used? Canceling Brightness UniformityWhat is a Blend? Main Functions Edge Blending Procedure Other Functions Remote Control of the Projector 35. Set Starting Points for Each Projector 36. LED Status Display on Built-In No Signal User Errors Invalid User EntryInput Signal Errors Other Signal Error Messages System Errors Status LED Codes Error Codes f Code DescriptionPage Maintenance Lamps Appendix G for the lamp product safety data sheetPower Cord Rev 01/07 Christie DS+60/DW30/Matrix 3000 User’s Manual Cleaning and Maintenance Guide Part Description Frequency Lamp Replacement Replacing Remote Batteries To replace a lamp Rev 01/07 Christie DS+60/DW30/Matrix 3000 User’s Manual Replacing the Projection Lens Symptom Severe motion artifacts… TroubleshootingSymptom f The projector is on but there’s no display Symptom Display is jittery or unstable… Symptom Display has suddenly frozen… Symptom f The display is faint…Symptom Data is cropped from edges Symptom Colors in the display are inaccurate… Lamps EthernetPage Specifications Lenses f Optional Composite Video and S-Video Remote ControlWired Control DVI-I Analog Lamps f Type Size and WeightGeneral Environment Non-Operating f TemperatureOptional Accessories Standard ComponentsPage Glossary Chrominance Channel NumberCheckbox Color Gamut Dot Clock Display SettingDiffused Screen Flicker Interlace Input SignalInterface Keypad PAL Video Resolution lensResolution projector Pixel Video Source SetupSwitcher Scan Line Video Decoder Vertical FrequencyVertical Offset Video StandardPage IR Remote Key Reference Page Serial Communication Cables Page Throw Distance Calculating Throw DistancePage GIO C2 O Configuring the GpioSystem Integration GIO 2 H Set pin #2 to high state Query Command Real Time Event Optional Input Modules Input Module RGB400ALT FeaturesPC250 Analog Features 38-804607-xx Dual SD/HD-SDI Features FeaturesSDI Features DVI Input ModulePage 300W P-VIPProduct Safety Data Sheet Page Page Page Index Index RGB Index