E6580757
11.Table of parameters and data
11.1User parameters
*1 : The end of type – form depend
|
|
|
|
|
| AN – WN : 60Hz |
| |
|
|
|
|
|
| WP : 50Hz |
| |
|
|
|
|
| *2 : Model depend (See section 11 page | |||
Title | Function | Unit | Minimum | Adjustment range | Default |
| User | Reference |
|
|
| setting unit |
| setting |
| setting |
|
|
|
|
|
|
|
|
|
|
- | Applicable motor | Hz | - | 60 | *1 |
|
| 4.1 |
| base frequency *3 |
|
| 50 |
|
|
|
|
| Operation | Hz | 0.1 | - | 0.0 |
|
| 3.2 |
| frequency of |
|
|
|
|
|
|
|
| operation panel |
|
|
|
|
|
|
|
*3 : When the standard setting ( : ) is entered, this parameter displayed.
11.2Basic parameters
•Four automatic functions
Title | Communication | Function | Unit | Minimum | Adjustment range | Default | User | Reference |
|
| |
|
| No. |
|
| setting unit |
| setting | setting |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0000 | Automatic | - | - | 0: Disabled (manual) | 0 |
| 5.1 |
|
|
|
|
| acceleration/ |
|
| 1: Optimum rate |
|
|
|
|
|
|
|
| deceleration |
|
| 2: Minimum rate |
|
|
|
|
|
|
| 0001 | Automatic torque | - | - | 0: Disabled | 0 |
| 5.2 |
|
|
|
|
| boost |
|
| 1: Vector control + |
|
|
|
|
|
|
| 0002 | Automatic | - | - | 0: Disabled | 0 |
| 5.3 |
|
|
|
|
| environment |
|
| 1: Automatic setting |
|
|
|
|
|
|
|
| setting |
|
|
|
|
|
|
|
|
|
| 0040 | Automatic function | - | - | 0: Disabled | 0 |
| 5.4 |
|
|
|
|
| setting |
|
| 1: Coast stop |
|
|
|
|
|
|
|
|
|
|
| 2: |
|
|
|
|
|
|
|
|
|
|
| 3: External input UP/DOWN setting |
|
|
|
|
|
|
|
|
|
|
| 4: |
|
|
|
|
|
| • | Other | basic parameters |
|
|
|
|
|
|
| |
Title | Communication | Function | Unit | Minimum | Adjustment range | Default | User | Reference |
|
| |
|
| No. |
|
| setting unit |
| setting | setting |
|
|
|
|
|
|
|
|
|
| 11 | ||||
|
|
|
|
|
|
|
|
|
|
| |
|
| 0003 | Command mode | - | - | 0: Terminal board | 1 |
| 5.5 |
| |
|
|
| selection |
|
| 1: Operation panel |
|
|
|
| |
|
| 0004 | Frequency setting | - | - | 0: Terminal board | 2 |
| 5.5 |
|
|
|
|
|
| ||||||||
|
|
| mode selection |
|
| 1: Operation panel |
|
|
|
|
|
|
|
|
|
|
| 2: Internal potentiometer |
|
|
|
|
|
|
| 0005 | Meter selection | - | - | 0: Output frequency | 0 |
| 5.6 |
|
|
|
|
|
|
|
| 1: Output current |
|
|
|
|
|
|
|
|
|
|
| 2: Set frequency |
|
|
|
|
|
|
|
|
|
|
| 3: For adjustment (current fixed at |
|
|
|
|
|
|
|
|
|
|
| 100%) |
|
|
|
|
|
|
|
|
|
|
| 4: Inverter load factor |
|
|
|
|
|
|
|
|
|
|
| 5: Output power |
|
|
|
|
|
|
| 0006 | Meter adjustment | - | - |
| - |
| 5.6 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0007 | Standard setting | - | - | 0 ∼ 2: | 0 |
| 5.7 |
|
|
|
|
| mode selection |
|
| 3: Default setting |
|
|
|
|
|
|
|
|
|
|
| 4: Trip clear |
|
|
|
|
|
|
|
|
|
|
| 5: Cumulative operation time clear |
|
|
|
|
|
|
|
|
|
|
| 6: Initialization of type information |
|
|
|
|
|