Toshiba VF-S9 manual Effect Reactor type Power factor Harmonics Suppression, LC filter, NF type

									E6580757
					Optional external devices
No.		Device			Function and purpose
	Input AC reactor		Used to improve the input power factor, reduce the harmonics, and suppress external
			surge on the inverter power source side. Install when the power capacity is 500 kVA or
			more and 10 times or more than the inverter capacity or when a distorted wave genera-
			tion source such as a thyristor unit or a large-capacity inverter is connected in the same
			distribution system.
(1)						Effect
				Reactor type	Power factor	Harmonics Suppression			External surge
						200V-3.7kW
					improvement			Other model	suppression
						or less
				Input AC reactor	{	{		{	{
				DC reactor	{ Large	{		{ Large	⋅
				{ Large : Large effective. { : effective. ⋅ : ineffective
	DC reactor		Improves the power factor more than the input reactor. When the facility applying the
			inverter requires high reliability, it is recommended to use the DC reactor with an input re-
			actor effective for external surge suppression.
(2)			* An inverter unit of 200V-3.7kW or less is connected to a reactor selected on page J-8, 9
				to conform “Guides of limits for harmonics current emissions on general purpose
				inverter having an input current up to and including 20A per phase” by the Japan Elec-
				trical Manufacturers’ Association.
		High-attenuation filter	These types of filters are not necessary because all single-phase 200V or 3-phase 400V
		(LC filter)	models and 3-phase 200V, 5.5kW or 7.5kW models have a built-in EMI noise filter, con-
		NF type	forming to Class A, as standard. But install these filters if necessarily of noise reduction
		manufactured by	move and more.
(3)	filter	Soshin Electric Co.	• Effective to prevent interference in audio equipment used near the inverter.
			• Install on the input side of the inverter.
	reduction	Zero-phase reactor	• Provided with wide-range attenuation characteristics from AM radio bands to near
			• Effective to prevent interference in audio equipment used near the inverter.
				10MHz.
			• Use when equipment readily affected by noise is installed in the peripheral area.
	noise	(Inductive filter)	• Effective in noise reduction on both input and output sides of the inverter.
(4)		Ferrite core type	• Provided with attenuation characteristics of several dB in frequencies from AM radio
	Radio	manufactured by		bands to 10MHz.
		Soshin Electric Co.	• For noise countermeasures, insert on the secondary side of the inverter.
										10
		Foot-mounted type	High-attenuation EMI noise filter requiring only small space; mounted on the rear side of
		noise reduction filter	the inverter. This filter can be installed to conform to the following classes of EMC stan-
(5)		(Soon to be	dard EN5501 Group 1.
		released)	3-phase 200V models excluding those of 5.5/7.5kW				: Conform to Class A.
			All models other than above				: Conform to Class B.
	Braking resistor		Use when rapid deceleration or stop is frequently required or when it is desired to reduce
(6)			the deceleration time with large load. This resistor consumes regenerative energy during
			power generation braking.
			• Braking resistor – With (resistor + protective thermal relay) built in.
	Motor-end surge voltage		Use an insulation-reinforced motor or install the surge voltage restraint filter to prevent
(7)	suppression filter (400V		degrading motor insulation caused by surge voltage generation depending on cable
	class only)		length and wiring method, or use of a 400V class motor driven with an inverter.
(8)	Conduit pipe kit		Attachment kit used for conformance to NEMA TYPE1.
	(Soon to be released)
(9)	IP43 enclosure kit		Attachment kit for making a panel conform to the IP43 structure.
	(Soon to be released)
(10)	DIN rail kit		Available for the 200V class models of 0.75kW or less. (Model: DIN001Z)
	(Soon to be released)

J-5