Toshiba VF-S9 manual Selection of wiring devices

E6580757

■Selection of wiring devices

			Non-fuse circuit		Magnetic contactor		Overload relay		Earth leakage
	Capacity of		breaker		(MC)		(THR)		breaker
Voltage class	applicable	Inverter model	(MCCB)						(ELCB)
	motor		Rated	Type	Rated	Type	Adjusted current	Type	Rated	Type
	(kW)		current	Note1)	current	Note1)	(A)	Note1)	current	Note1)
			(A)		(A)		(For reference)		(A)
	0.2	VFS9S-2002PL	10	NJ30N	11	C11J	1.3	T13J	10	NJV50E
Single-phase	0.4	VFS9S-2004PL	15	NJ30N	11	C11J	2.3	T13J	15	NJV50E
	0.75	VFS9S-2007PL	20	NJ30N	11	C11J	3.6	T13J	20	NJV50E
200V class
	1.5	VFS9S-2015PL	30	NJ30N	18	C20J	6.8	T13J	30	NJV50E
	2.2	VFS9S-2022PL	40	NJ50E	35	C35J	9.3	T13J	40	NJV50E
	0.2	VFS9-2002PM	5	NJ30N	11	C11J	1.3	T13J	5	NJV50E
	0.4	VFS9-2004PM	5	NJ30N	11	C11J	2.3	T13J	5	NJV50E
	0.75	VFS9-2007PM	10	NJ30N	11	C11J	3.6	T13J	10	NJV50E
Three-phase	1.5	VFS9-2015PM	15	NJ30N	11	C11J	6.8	T13J	15	NJV50E
	2.2	VFS9-2022PM	20	NJ30N	13	C13J	9.3	T13J	20	NJV50E
200V class	3.7	VFS9-2037PM	30	NJ30N	26	C25J	15	T20J	30	NJV50E
	5.5	VFS9-2055PL	50	NJ50E	35	C35J	22	T35J	50	NJV50E
	7.5	VFS9-2075PL	60	EJ100F	50	C50J	28	T35J	60	NJV60F
	11	VFS9-2110PM	100	EJ100F	65	C65J	44	T65J	100	NJV100F
	15	VFS9-2150PM	125	EJ225F	80	C80A	57	T65J	125	NJV225F
	0.75	VFS9-4007PL	5	NJ30N	9	C11J	1.6	T13J	5	NJV50E
	1.5	VFS9-4015PL	10	NJ30N	9	C11J	3.6	T13J	10	NJV50E
Three-phase	2.2	VFS9-4022PL	15	NJ30N	9	C11J	5.0	T13J	15	NJV50E
	3.7	VFS9-4037PL	20	NJ30N	13	C13J	6.8	T13J	20	NJV50E
400V class	5.5	VFS9-4055PL	30	NJ30N	17	C20J	11	T13J	30	NJV50E
	7.5	VFS9-4075PL	30	NJ30N	25	C25J	15	T20J	30	NJV50E
	11	VFS9-4110PL	50	EJ50E	33	C35J	22	T35J	50	NJV50E
	15	VFS9-4150PL	60	EJ100F	48	C50J	28	T35J	60	NJV100F

Note 1: Produced by Schneider Toshiba electric corporation.

Note 2: Be sure to attach a surge killer to the exciting coil of the relay and the magnetic contactor. Selection of surge killers for Toshiba magnetic contactors

200V class: Surge absorbing units are optionally available for Toshiba C11J to C65J, or Model SS-2 for C50J and C65J

400V class: For the operation and control circuits, regulate the voltage at 200V or less with a step-down

	transformer.
10
	Note 3: When using the auxiliary contacts 2a of the magnetic contactor MC for the control circuit, connect the
	contacts 2a in parallel to increase reliability.
	Of the wiring devices listed in the above table, the magnetic contactors (MC) and the overload relays (Th-Ry) are
	intended for use with the Mighty J series. When using the old series (ESPER Mighty series), refer to the table
	below showing the correspondence between the two series.
	Magnetic contactor (MC)		Overload relay
	ESPER Mighty series	Mighty J series	ESPER Mighty series	Mighty J series
	C12A	C13J	T11A	T13J
	C20A	C20J	T20A	T20J
	C35A	C35J	T35A	T35J
	C50A	C50J	T65A	T65J
	C65A	C65J

J-2