Setting environmental protection | Toshiba VF-S9 manual

E6580757

5.3Setting environmental protection

: Automatic environment setting

• Function

This automatically programs all parameters related to inverter environmental protection (auto-restart or ride-through control after momentary power failure, supply voltage correction, acceleration/deceleration S- pattern).

This parameter is especially suitable for wind force or hydraulic machinery such as fans and pumps Note: Do not use this parameter for equipment such as transporters, since it is dangerous to operate

automatically such equipment after temporary stops.

[Parameter setting]

Title	Function	Adjustment range	Default setting

	Automatic environment setting	0: Disabled	0
		1: Automatic setting
					5

Values of automatically programmed parameters
Values of automatically programmed parameters
Title	Function		Default setting


	Auto-restart control selection	1: At auto-restart after	0: Disabled
	Auto-restart control selection	momentary stop	0: Disabled
		momentary stop
	Regenerative power ride-through control	1: Enabled	0: Disabled

		1: Supply voltage	1: Supply voltage cor-
	Supply voltage correction	corrected, output volt-	rected, output voltage
		age limited	limited
	Acceleration/deceleration 1 pattern	1: S-pattern 1	0: Linear

5.4Setting parameters by operating method

: Automatic function setting

• Function

Automatically programs all parameters (parameters described below) related to the functions by selecting the inverter's operating method.

The major functions can be programmed simply.

[Parameter setting]

Title	Function	Adjustment range	Default setting

		0: Disabled
		1: Coast stop
	Automatic function setting	2: 3-wire operation	0
		3: External input UP/DOWN setting
		4: 4-20mA current input operation

E-5

Image 65

Toshiba VF-S9 Setting environmental protection, Setting parameters by operating method, Automatic environment setting

Contents

Tosvert VF-S9 Contents E6580757 Iii Meanings of symbols Safety precautionsSafety precautions Explanation of markings General operation Wiring Transportation ‚ Installation Operations Maintenance and inspection When retry function is selected inverter Attach warning labels Disposal II. Introduction Features Mandatory Read firstCheck product purchase Contents of the product code Outside view Names and functions Terminal board cover Charge lamp E6580757 2022PL Main circuit and control circuit terminal boards VFS9-2022PM/2037PM VFS9-4007PL ∼ 4037PL 2015PM VFS9-2055PL/2075PL 4055PL/4075PL See 2.3.2 for details on all terminal functions How to open the front terminal board cover Motors Extremely low loads and low inertia loads Braking a motor when cutting off power supplyOccurrence of instability Loads that generate negative torque Inverters Power factor improving capacitorsProtecting inverters from overcurrent Inverter capacity Effects of leak current across ground What to do about leak currentCircuit interupting fuse MCCBn+1 INVn Remedies PowerFfects of leak current across lines Supply Use the electronic thermal built into the inverter Installation environment InstallationContinuous operation this may result in fire Not examples for resistance to fire or explosion Consult with Toshiba about these measures Installation location How to install Inverter Type Cabinet must be ventilated and cooled Installing more than one unit in a cabinet Connection equipment Preventing radio noise Control and main power supplyWiring Standard connections This diagram shows a standard wiring of the main circuit Standard connection diagram 1 sink common CC VF-S9 Standard connection diagram 2 source common P24 Description of terminals Power supply and motor connectionsMain circuit terminals Connections with peripheral equipment Main circuit Control circuit terminals sink logic ~60Hz60Hz setting frequency Input Standard default setting 0~10Vdc input Internal impedPut. Standard default setting output cur 1mA full-scale dc By jumper JP302 switching Full scale DC am = 1, 30Vdc-1A, 250Vac-1A cos φ = At resistance load Multifunction programmable relay contactOutput Detects the operation of the inverters 30Vdc-1A During protection function operation Input Common Output Logic switching/voltage-current output switching jumper Operations Wiring How to operate the VF-S9Motor Main circuit E6580757 Mccb Motor Monitor display selection Is set to Adjustment rangeSimplified Operation of the VF-S9 How to set the frequency How to start and stop Example of operating a run from the panel Setting the frequency using the operation panelMoves the frequency down Potentiometer E6580757 Status monitor mode Mode for monitoring all inverter status Setting monitor mode Mode for setting inverter parametersBasic VF-S9 operations VF-S9 has the following three monitor modes Setting monitor mode How to set parameters Press the Enter key to save the changed maximum frequency How to set the basic parameters Key and the key to select How to set extended parameters Key to change the dynamic braking selection from Search and resetting of changed parametersExample of parameter setting How to search and reprogram parameters How to program setup parameters Parameters that cannot be changed while running Returning all parameters to standard default settingCommand mode selection Set , and and can Pressing the Enter key displays Key operated LED display OperationKey or the key to change the set value. To return to Basic parameters Setting acceleration/deceleration timeAutomatic acceleration/deceleration Set automatic acceleration/deceleration to or Parameter setting Title Function Adjustment range Manually setting acceleration/deceleration timeAcceleration time Seconds Deceleration time Seconds Automatic torque boost Increasing starting torque Set V/F control mode selection to 0 V/F constant Automatic torque boost and V/F control mode selectionIf auto-tuning error Appears, see 6.13 Auto Setting parameters by operating method Setting environmental protectionAutomatic environment setting Automatic function setting VIA/II UP/DOWN Command mode selection Frequency setting mode selection Selection of operation modeCommand mode selection Title Function Adjustment range Meter selection Meter adjustment Meter setting and adjustmentPreset-speed operation Resolution Adjustment scale with meter adjustment parameterExample of 4-20mA programmed output for details, see Connect meters as shown below Adjusting the meter in inverter stop state Standard default settingDefault setting Tion Is set to Parameter setting Setting valuesSelecting forward and reverse runs operation panel only Forward/reverse run selection Upper limit and lower limit frequencies Maximum frequencyMaximum frequency Upper limit frequency Lower limit frequency Base frequency 25 ∼ 400 Hz Base frequencyBase frequency Control mode selection Selecting control modeTime Selection Setting for fans and pumps Constant torque characteristics general method of use Increasing starting torque Setting V/F control selection Automatic torque boostMotor constant must be set This gives steady torque for stable runs Energy-saving Precautions on vector controlSorless vector control Somewhat lower Torque boost Setting the electronic thermalManual torque boost increasing torque at low speeds Overload Title Function Adjustment range Default settingProtection Stall Motor electronic thermal pro Default setting 100% Press Key to change the parameter to Setting of motor electronic thermal protection level Setting value Overload protection Overload stall Setting the motor electronic thermal protection level Inverter over load characteristics Preset-speed operation speeds in 15 stepsPreset-speed operation frequencies 1~7 Preset-speed operation frequencies 8~15 S3-CC Preset-speedTerminal functions are as follows Terminal S1 =6 SS1 Example of 7-step speed operation Using other speed commands with preset-speed command Low-speed signal output frequency Low-speed signalLow-speed signal output frequency ∼ Hz Extended parameters Speed reach detection band Output of designated frequency reach signalParameter setting of output terminal selection Speed reach setting frequency Speed reach detection band Output of set frequency speed reach signalParameter setting of set frequency and detection band Title Function Adjustment range Setting ST standby signal selection Input signal selectionChanging the standby signal function Setting the reset signal Keeping an input terminal function always active on Terminal function selectionModifying input terminal functions Always-active function selection Terminal Title Function Adjustment range Default setting Setting of contact input terminal functionInput terminal selection 3 RST Reset Connection method Contact input Sink logic Case of three-wire operation Set to Example of application ... Three-wire operationSink logic/source logic input Input terminal selection Modifying output terminal functions Setting of output terminal functionExamples of application Output terminal selection Basic parameters Switching motor characteristics via terminal inputSetting of switching terminals Frequency priority selection Automatic frequency switching Set frequency is cleared automatically after power-off External switching Fchg enabledExternal contact UP/DOWN Contact input. See Setting frequency command characteristics 20mAdc current input adjustment 10Vdc voltage input adjustment VIA, VIB Adjustment with pulse signals Parameter-setting example Sample sequence diagram 1 Adjustment with continuous signals Frequency adjustment range Sample sequence diagram 2 Adjustment with pulse signalsMinimum unit of frequency adjustment Simultaneous input Operation frequency Starting frequency settingStarting frequency Function Frequency set with the parameter DC braking 2 Run/stop control with frequency setting signalsDC braking DC braking time 20.0 sec Jog run modeJog run frequency Jog run stopping pattern Jog run setting Jump frequency Jumping width Jump frequency 3 Jumping width Jump frequency jumping resonant frequencies ∼ Preset-speed operation frequency 8 to Preset-speed operation frequency 8 toRandom mode PWM carrier frequency Auto-restart control selection Trip-less intensificationAuto-restart Restart during coasting DC braking during restart Restarting motor during coasting Motor speed search function Regenerative power ride-through control Regenerative power ride-through controlIf momentary power failure occurs Application Retry selection Canceling conditionsRetry function Dynamic braking selection Braking resistor operation rate Dynamic regenerative braking Separate-type optional resistor with thermal fuse Connecting an external braking resistor optionalParameter setting Title Function Setting the braking resistor operation rate Overvoltage limit operation 12.5 Avoiding overvoltage trippingMinimum resistances of connectable braking resistors To the base frequency So that no Output voltage adjustment/Supply voltage correction Output voltage unlimited External connection Conducting PI control100.0 Integral gain 100.0 Adjusting the PI control gain level Setting PI controlGain adjustment parameter Types of PI control interfaces Adjusting analog command voltages Selection 1 Setting by automatic torque boost Setting motor constantsSet the auto-tuning parameter to See .2 for details of the setting method Rameters Auto-tuning Application of individual settings To the actual operation Perform adjustments according to the actual operation Acceleration time 3600 s Deceleration time 3600 s Linear acceleration/deceleration Acceleration/deceleration patterns Selection using parameters Switching to acceleration/deceleration Protection functions Setting motor electronic thermal protection Inverter trip retention Setting current stallStall prevention level Inverter trip retention selection External trip stop via terminals External input trip stop mode selectionIs set to Emergency DC braking, also set Emergency DC braking time Output phase failure detection mode selection Output phase failure detectionFailure detection signal generated FL relay deactivated Emergency stopping from the operation panel Input phase failure detection mode selection Input phase failure detectionControl mode for small current Disabled Enabled Over-torque trip/alarm level ∼ 250 % Specified time Title Function Adjustment rangeOver-torque trip Level flows for more than No trip Over-torque detection Pre-alarm signal Detection signalOutput terminal function 12 OT Over-torque detection No trip Over-torque 15.10 4-20mA dc calibration Undervoltage tripUndervoltage trip selection Meter bias Examples of setting Prohibition of change of parameter settingsProhibition of change of parameter settings Setting methods Changing the display unit to A/V/min-1 Resetting methodUnit selection Free unit selection Display in percentage terms Display in amperes/volts Standard monitor mode ⇒ Standard monitor display selection Changing the display format while power is onChanging the status monitor display format Standard monitor display selection Communication function Common serial Setting the communication functions Using the RS232C/RS485Transmission specifications Communication function parameters Common serial options Example of connection for RS485-communication Command by communicating independentlyNext data Use the terminal board to branch the cable Number, to the host computer Applied operation Setting the operation frequencyOperation panel key setting S1 UP S2 Down S3 CLR Switching between external contact UP/DOWN VIA input Preset-speed settingTo switch to VIA/II setting, use the external PNL/TB S1FCHG Signal Voltage signal Switching between analog setting and preset-speed settingSetting by means of a remote input device Operation is controlled in accordance with Setting Terminal board operation Setting the operation mode Enable to run at HD on Case of three wire operation Set toEration holding S1 terminal set to Operation, inverter stop Operation from an external input device S2 PNL/TB VIA VIB OFF LED Display of trip information Display of trip information Example of call-up of trip information E6580757 About the EMC directive How to cope with the CE directiveTaking measures to satisfy the CE/UL directive Measures to satisfy the EMC directive Single-phase 200V class Example of wiring Measures to satisfy the low-voltage directive About the low-voltage directiveInverter satisfies the low-voltage directive Plate. Refer to the .1 for earth cable sizes Peripheral devices Selection of wiring materials and devices Selection of wiring devices Magnetic contactor in the secondary circuit Installation of a magnetic contactorMagnetic contactor in the primary circuit Optional external devices Installation of an overload relay 200V-3.7kW Improvement Other model Effect Reactor type Power factor Harmonics SuppressionOr less Input AC reactor DC reactor Actor effective for external surge suppression Parameter writer Ward/reverse switch Model CBVR-7B1Model PWU001Z Extension panel UP/DOWN key, Monitor key, and Enter key Model RKP001Z Input AC re Actor Devices DCL Noise filter Devices External dimensions and connections Foot Mounted Devices External dimensions and connections Braking Resistor Writer Exten Devices External dimensions and connections ParameterSion panel Communica User parameters Table of parameters and dataFour automatic functions Other Basic parameters Input/output parameters Extended parameters VIB, VIA/II Frequency parameters 0213 VIB input point 400 Frequency Frequency Down Operation mode parameters Protection parameters Torque boost parametersAcceleration/deceleration time parameters Communication parameters Operation panel parameters Table of input terminal functions 1/3 Default settings by inverter rating ST+PNL/TB Table of input terminal functions 2/3 Table of output terminal functions 1/2 Table of input terminal functions 3/3 POL Table of output terminal functions 2/2 Order of precedence of combined functions Standard specifications SpecificationsModels and their standard specifications Specification Outside dimensions and mass Outside dimensions and mass Plate Fig.A Trip causes/warnings and remedies Before making a service call Trip information and remedies Problem Possible causes Remedies Overvoltage during Problem Possible causes Remedies Small-current opera Process of initializa Values Restoring the inverter from a trip If the motor does not run while no trip message is displayed How to determine the causes of other problems How to cope with parameter setting-related problems Regular inspection Inspection and maintenance Check points Periodical inspectionCheck items Call the local sales agency Replacement of expendable parts Keeping the inverter in storage Standard replacement cycles of principal partsMaking a call for servicing Warranty Disposal of the inverter Toshiba Corporation