E6580757
13.3If the motor does not run while no trip message is displayed ...
If the motor does not run while no trip message is displayed, follow these steps to track down the cause.
The motor does not run.
Is the
Is displayed?
YES :
NO :
Check the power supply and the MCCB. |
| Supply the power |
Is power being supplied normally? |
| normally. |
|
|
|
Make a service call.
•The
•Properly change the setting of the ST (standby) signal selection parameter
. (See 6.2.1.)
Is any failure message displayed? (See 13.1.)
Track down and eliminate the cause of the failure and then reset the inverter. See 13.2.
Are |
| and a failure message |
|
|
| The inverter is in the process of retrying. The retry function can be disabled by |
| ||||||
|
|
|
| |||
| ||||||
displayed alternately? |
|
| normal or emergency stop operation, or by turning off the inverter. | |||
|
|
|
|
|
| |
|
|
|
|
|
|
|
Is the LED of the RUN/STOP key lighted?
Is the LED of the RUN/STOP key off?
•When operation panel operation is selected ...
Press the RUN key to start the operation.
•Check whether the operation panel operation frequency is set properly. (See 3.2.2.)
•When another control mode is selected ...
Change the setting of the operation control mode selection . (See 3.2.1.)
•When operation panel operation is selected ...
Change the setting of the operation control mode selection parameter
to 1. (See 5.5.)
•You can check the setting of each input terminal on the monitor. (See 8.1.)
•When another control mode is selected ...
Check whether the external operation command is entered.
|
| Is : |
| displayed? |
|
| • Check to see that the frequency setting signal is not set at zero. |
|
|
| ||||||||
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
| • | Check the settings of the frequency setting signal parameters |
| , |
| , | ||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
|
|
| ||||||||
|
|
|
|
|
|
|
|
| • |
| and |
| . (See 6.5.) |
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| Check the frequency setting signal points 1 and 2 settings. (See 6.5.) |
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| • Check that the | |||||||||
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
| ||||||||||
|
|
|
|
|
|
|
|
|
| 6.6.) |
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
13 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| • Check that the frequency setting | ||||||||||
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
| at zero. |
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
| • | Check that the motor is not under a too large load or not locked up. | |||||||||
|
|
|
|
|
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
| load if necessary. |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Determine the cause, using the parameter display function and the status monitoring function.
Refer to Section 11 for the parameter display function or Section 8 for the status motoring function.