|
|
|
|
|
|
|
| E6580757 | |
|
|
|
|
|
|
|
|
|
|
|
|
| Automatically programmed functions and parameter set values |
|
|
| |||
|
|
|
| Default setting | 1: Coast stop | 2: | 3: External input | 4: |
|
|
|
|
|
|
| tion | UP/DOWN set- | input operation |
|
|
|
|
|
|
|
| ting |
|
|
|
|
|
| 2: Potentiometer | 2: Potentiometer | 2: Potentiometer | 1: Operation | 0: Terminal board |
|
|
|
|
| panel |
| ||||
|
|
|
|
|
|
|
|
| |
|
|
|
| 1: Operation | 0: Terminal board | 0: Terminal board | 0: Terminal board | 0: Terminal board |
|
|
|
|
| panel |
| ||||
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| (F) | 2: F | 2: F | 2: F | 2: F | 2: F |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (R) | 3: R | 3: R | 3: R | 3: R | 3: R |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (RST) | 10: RST | 10: RST | 10: RST | 10: RST | 10: RST |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (S1) | 6: SS1 | 6: SS1 | 6: SS1 | 41: UP | 6: SS1 |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (S2) | 7: SS2 | 7: SS2 | 7: SS2 | 42: DOWN | 38: FCHG |
|
|
|
|
|
|
|
|
|
|
|
|
|
| (S3) | 8: SS3 | 1: ST | 49: HD | 43: CLR | 1: ST |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 0: Activated by |
|
| 0: Activated by | |
5 |
|
|
|
|
|
| |||
|
| (ST) | 1: Always active | turning ST on | 1: Always active | 1: Always active | turning ST on |
| |
|
|
|
| active |
|
| active |
| |
|
|
|
| 0: VIA/II | 0: VIA/II | 0: VIA/II | 3: UP/DOWN | 0: VIA/II |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | - | - | - | 20% |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | - | - | - | - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | - | - | - | - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | - | - | - | - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | - | - | 1 | - |
|
|
|
|
| - | - | - | 0.1Hz | - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | - | - | 1 | - |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| - | - | - | 0.1Hz | - |
|
|
|
|
|
|
|
|
|
|
|
Disabled ( )
Input terminals and parameters are standards programmed at the factory.
Coast stop ( )
Setting for coast stopping. ST (standby signal) is assigned to the S3 terminal and the operation is controlled by the on and off of the S3 terminal.
Can be operated by a momentary push-button. HD (operation holding) is assigned to the terminal S3. A self-holding of operations is made in the inverter by connecting the stop switch (b-contact) to the S3 termi-
nal and connecting the running switch
( )
Allows setting of frequency with the input from an external contact. Can be applied to changes of frequen- cies from several locations. UP (frequency up signal input from external contact) is assigned to the S1 ter-