Parameter Description and Options
FORM
TABLE 7-1 – DEFINITIONS (CONTINUED)
MENU ITEM | DEFINITION | |
HEAT 1 MIN RUN TIMER | THIS GIVES THE ACTUAL TIME OF THE MINIMUM RUN TIME | |
TIMER FOR HEAT SECTION 1 IN SECONDS | ||
| ||
HEAT 2 (W2) | THIS IS THE STATUS OF THE BINARY INPUT TO TERMINAL W2 | |
- SECOND STAGE HEATING | ||
| ||
HEAT 2 ASCD TIMER | THIS GIVES THE ACTUAL TIME OF THE OFF CYCLE TIMER FOR | |
HEAT SECTION 2 IN SECONDS. | ||
| ||
HEAT 2 MIN RUN TIMER | THIS GIVES THE ACTUAL TIME OF THE MINIMUM RUN TIME | |
TIMER FOR HEAT SECTION 2 IN SECONDS | ||
| ||
HEAT 3 (W3) | THIS IS THE STATUS OF THE BINARY INPUT TO TERMINAL W3 | |
- THIRD STAGE HEATING | ||
| ||
HEAT 3 ASCD TIMER | THIS GIVES THE ACTUAL TIME OF THE OFF CYCLE TIMER FOR | |
HEAT SECTION 3 IN SECONDS. | ||
| ||
HEAT 3 MIN RUN TIMER | THIS GIVES THE ACTUAL TIME OF THE MINIMUM RUN TIME | |
TIMER FOR HEAT SECTION 3 IN SECONDS | ||
| ||
| IN THE INTERMITTENT FAN MODE THIS IS THE TIME DELAY | |
HEAT FAN OFF DELAY | BETWEEN THE TIME THE HEAT CALL IS TERMINATED AND THE | |
| SHUT DOWN OF THE SUPPLY FAN | |
| IN THE INTERMITTENT FAN MODE THIS IS THE TIME DELAY | |
HEAT FAN ON DELAY | BETWEEN THE TIME THE HEATING OPERATION IS VERIFIED | |
| AND THE START OF SUPPLY FAN OPERATION | |
HEATING MODE ENABLED FOR OPERATION | THIS PARAMETER MUST BE TURNED ON TO ALLOW HEATING | |
OPERATION | ||
| ||
HEATING NUMBER #1 ACCUMULATED RUNTIME | THIS IS THE NUMBER OF HOURS THAT HEATING SYSTEM 1 HAS | |
BEEN OPERATIVE | ||
| ||
HEATING NUMBER #2 ACCUMULATED RUNTIME | THIS IS THE NUMBER OF HOURS THAT HEATING SYSTEM 2 HAS | |
BEEN OPERATIVE | ||
| ||
HEATING NUMBER #3 ACCUMULATED RUNTIME | THIS IS THE NUMBER OF HOURS THAT HEATING SYSTEM 3 HAS | |
BEEN OPERATIVE | ||
| ||
HEATING OUTPUT #1 (H1) | THIS IS THE STATUS OF THE BINARY OUTPUT FROM THE UNIT | |
CONTROLLER TO HEAT SECTION # 1, OFF/ON | ||
| ||
HEATING OUTPUT #2 (H2) | THIS IS THE STATUS OF THE BINARY OUTPUT FROM THE UNIT | |
CONTROLLER TO HEAT SECTION # 2, OFF/ON | ||
| ||
HEATING OUTPUT #3 (H3) | THIS IS THE STATUS OF THE BINARY OUTPUT FROM THE UNIT | |
CONTROLLER TO HEAT SECTION # 3, OFF/ON | ||
| ||
HOT GAS PRESENT ON COMPRESSOR # 1 | THIS PARAMETER MUST BE TURNED ON WHEN HOT GAS | |
BYPASS IS INSTALLED | ||
| ||
HOT GAS REHEAT | THIS PARAMETER WOULD BE TURNED ON TO ENABLE HOT GAS | |
REHEAT. THIS FEATURE IS NOT AVAILABLE ON THESE UNITS | ||
| ||
HOT WATER VALVE OUTPUT STATUS | THIS GIVES THE STATUS OF THE ANALOG UNIT CONTROLLER | |
OUTPUT TO THE HYDRONIC VALVE IN % | ||
| ||
HOT WATER VALVE OUTPUT STATUS | THIS GIVES THE STATUS OF THE ANALOG UNIT CONTROLLER | |
OUTPUT TO THE HYDRONIC VALVE IN % WHEN THE UNIT IS | ||
(REVERSE ACTING) | ||
PROGRAMMED FOR A REVERSE ACTING VALVE | ||
| ||
| THIS PARAMETER IS USED TO ENTER THE HOUR OF THE | |
HOUR | CURRENT TIME BASED ON A 24 HOUR SCHEDULE, 13 WOULD | |
| BE 1 PM | |
| Continued on next page |
146 | JOHNSON CONTROLS |
