Agilent Technologies 8922M, S GSM manual Index-7

Index

OTP memory cards, 8-21 open loop AGC calibration

RF analyzer, 4-113 Open/Auto DAC Value RF Analyzer, 4-114

open-loop AGC

RF analyzer, 4-112 operating environment, 1-8 Opt 001 Ref Out, 4-51 options, 1-8

originate call

keys, 5-6 oscilloscope, 4-75

arming, 4-78 trigger level, 4-78 triggering, 4-78

oscilloscope test, 3-10 Other fusing, 1-3 Output Destination

CRT or Printer, 8-31

Output Heading comments, 8-31 Output Results

All or Failures, 8-30 Output RF Spectrum

Output RF Spectrum (Main View), 4- 83

output rf spectrum cell control, 4-28

output RF spectrum measurement, 2-20 OutRFSpec

Output RF Spectrum (Trace View), 4- 85

P

Pages

Cell Control, 4-42 pages

call counts, 4-42 Paging

Cell Control, 4-42 Parallel Port

connector, 6-15 parameters

enter into Test Executive, 8-34 Parity, 8-6

Configure, 4-61 Pass Filter, A-12

Logging, A-12 Pause, A-11 PCN interface

connector, 6-15 Peak (Marker To)

Spectrum Analyzer (Marker Controls), 4-125

peak carrier power measurement, 2-14 Peak Phase Error

Phase/Freq (Main), 4-87 Phase/Freq (Multi-burst), 4-89

peak power

cell control, 4-28

peak transmitted power, 4-102 performance test software, 3-5 performance tests, 3-2 performance verification, 3-2 Personality, A-6, A-7

setting, A-6, A-7 phase and frequency cell control, 4-28

phase error, 4-91

phase error measurement, 2-15 Pk TX Pwr

Pwr Ramp (Summary), 4-102 Pls Demod

Audio, 4-4, 4-75, 4-77, 4-80 Polarity

Phase/Freq (Data Bits), 4-94 POnOffFall

Pulse Fall, 4-110 POnOffRise

Pulse Rise, 4-108 Pos/Neg

Oscilloscope (Trigger Controls), 4-78 Position

Oscilloscope (Marker Controls), 4-81 Spectrum Analyzer (Marker Controls),

4-126

power

continuous wave, 4-55 power cord, 1-4 power meter

zeroing, 4-29, 4-55, 4-103 power ramp measurement, 2-16 power supply

configure to GPIB, 8-35 ppm, 4-14

PRBS, 4-42 PRBS Pattrn, 4-42 Pre-Trig

Oscilloscope (Trigger Controls), 4-78 previous

keys, 5-6 print

keys, 5-6 print address

selecting, 4-61 Print Adrs, 8-5

Configure, 4-61 Print Cancel

Configure, 4-61 Print Title

Configure, 4-61 Print To, 8-5 printer

configure to GPIB, 8-35

for showing test results, 8-31 options, 8-35

RS-232 or GPIB, 8-31 printer port

I/O configuration, 4-61 printouts

for the test results, 8-30 problem solving, 2-30 Procedure Files, 8-26 Procedure files, 8-2

Program Development Tools disk, 8-16 Program Example, 8-37

PROGram Interface Commands, 8-16 Program Listing Explanation, 8-40 program status

run indicators, 8-29 Program Structure, 8-37 programming techniques, 8-29 programs

IBASIC file structures, 8-29 protocol buffer, A-8 protocol error messages, 7-5 protocol interface connector, A-2 Protocol Interface Port, A-11 protocol messages, A-8 Protocol Monitor, A-11 protocol units, A-8

Index-7