Agilent Technologies S GSM, 8922M manual Index-2

Index

Bit Error Test, 4-12 Bits to Test

Bit Error Test, 4-12 buffers, A-11

Burst Length Measurement Sync, 4-64

Burst Number Measurement Sync, 4-64

Burst Sel Measurement Sync, 4-65

burst selection

measurement synchronization, 4-65 Burst Type

Measurement Sync, 4-65 Burst Used

Measurement Sync, 4-65 Bursts

Phase/Freq (Data bits), 4-93 Phase/Freq (Phase Err), 4-91

bursts measured, 4-90

C

CA

Cell Configuration, 4-18, 4-24 cache, A-10

buffers, A-11 call count

reset, 4-43 call counts

frame errors, 4-31, 4-39 pages, 4-42

RACHs, 4-43 Call Status

Cell Control, 4-38 Caller

Cell Control, 4-38 Camping On, A-5

LAC, A-5

MCC, A-5

MNC, A-5

More information, A-5 Power level, A-5

camping on, 4-71 cancel

keys, 5-3

CBCH, 4-119	connector
cell allocation, 4-18, 4-24	protocol interface, A-2
cell configurationscreen	connectors
keys, 5-4	10 MHz output, 6-10
cell control	13 MHz output, 6-10
active cell+, 4-31	AM input, 6-11
cell control screen	AM/Speech input, 6-4
keys, 5-3	audio input (high), 6-5
Center Freq	audio input (low), 6-5
Spectrum Analyzer (Main Controls), 4-	audio output, 6-7
123	auxiliary RF input, 6-2
Center Freq (Marker To)	auxiliary RF output, 6-2
Spectrum Analyzer (Marker Controls),	clock, 6-3
4-125	clock output, 6-3
center frequency	data input/output, 6-6
spectrum analyzer, 4-123, 4-125	data output, 6-4
Clear Log, A-10, A-11	EMMI bus, 6-11
Agilent 8922M, A-10	FM output, 6-4
Logging, A-11	GPIB, 6-12
clock input	monitor, 6-7
connector, 6-3	opt 001 reference output, 6-14
clock input selection, 4-18, 4-24	oscilloscope input, 6-8
clock output	Parallel Port, 6-15
connector, 6-3	PCN Interface, 6-15
closed-loop AGC	Protocol Interface, 6-16
RF analyzer, 4-112	pulse modulation, 6-8
Code Files, 8-37	pulse output, 6-7
Code files, 8-2	reference input, 6-16
color code, 4-18, 4-24	reference output, 6-14
command line, 8-16	RF input/output, 6-8
comments	serial port, 6-17
for the Output Heading field, 8-31	speech, 6-7
communication failure message, 7-2	system bus, 6-17
completed bits tested	trigger input, 6-9
Bit Error Test, 4-9, 4-12, 4-15	valid data, 6-9
CONFIGURE, 8-5	video output, 6-17
CONFIGURE Screen	Cont/Single
Aux RF Out, 4-50	Oscilloscope (Trigger Controls), 4-78
Connect	Control
Cell Control, 4-39	Bit Error Test, 4-10
Connection, A-2, A-4	RF Analyzer, 4-113
Agilent 8922M to HP/Agilent 37900D,	Control Ch
A-4	Cell Config, 4-19, 4-25
bar graphs, A-9	control channel, 4-19, 4-25
checking, A-8	Control mode, 4-60
diagram, A-4	Controls
indication, A-9	Oscilloscope, 4-76
verification, A-9	Spectrum Analyzer (AuxiliaryCon-

Index-2