Manuals / NEC / Computer Equipment / Server

NEC 1080Xd manual Main Components, Itanium 2 Processors, System Memory, PCI-X Core Module

Models: 1080Xd

1 216

Download 216 pages 14.64 Kb

Page 23

Main Components

Main Components

The following sections provide information about the components in the main chassis.

Itanium 2 Processors

Depending on system configuration, your system includes four or eight Intel Itanium 2 64-bit 1.3-GHz/3-MB or 1.5-GHz/6.0-MB processors. Four Intel Itanium 2 processors are installed within one CELLV board. See Figure 1-5. A second CELLV board has an additional four Intel Itanium 2 processors. All processors installed in your system must be of identical bus and core speed.

System Memory

Each CELLV board in your system contains sixteen 168-pin DIMM sockets.

See Figure 1-5. Memory DIMMs must be populated four at a time with 1-GB ECC SDRAM DIMMs. Depending on the number of DIMMs installed, your system may include from 4 GB up to a maximum of 32 GB of memory using 1-GB DIMMs.

PCI-X Core Module

The server’s expansion capabilities meet the needs of file and application servers for high performance I/O by providing twelve hot-swap PCI-X expansion slots within the Core Module. The Core Module consists of a CrossBar Controller (XBC) and an I/O Router (IOR). The Core Module can be connected with up to two CELLV Boards, to control data transfers between the CELLV Boards.

The Core Module includes five full-length and three half-length 64-bit/66-MHz hot- swap PCI-X slots and three full-length and one half-length 64-bit/133-MHz hot-swap PCI-X slots. The PCI-X slots allow PCI-X boards to be installed or removed while the server is powered on (if the operating system supports the Hot Plug PCI function). A Basic I/O Board to support standard I/O interface and a video VGA controller board are installed in the Core Module. The Basic I/O Board and video VGA board are not hot- swappable.

Note: Your operating system must support the Hot Plug PCI function.

A DVD-ROM drive is installed in the Core Module as standard equipment. Optionally, a DAT tape drive or USB FDD and up to 4 disk storage hard disk drives may be added to the Core Module. See Figure 1-2.

System Overview 1-9

Image 23

NEC 1080Xd manual Main Components, Itanium 2 Processors, System Memory, PCI-X Core Module

Contents

U s e r ’ s G u i d e EXPRESS5800/1080XdPage Trademarks Proprietary Notice and Liability DisclaimerPage System Operation ContentsProprietary Notice Using This Guide System OverviewContents Service ProcessorBIOS Setup HBB Configuration Submenu Precaution I/O Board InstallationProblem Solving ContentsIndex A Technical SpecificationsMemory Upgrades Windows 2003 InstallationUsing This Guide Text Conventions Site Preparation Guide Related DocumentsInstallation Procedures System Release Notesx Using This Guide Safety NoticesSafety Notices for Users Outside of the U.S.A. and Canada xii Using This Guide Care and HandlingSecurity Overview System Features System Chassis System Functions ExpansionSystem Overview Overview System Features Optional PCIX Unit in two versions, Base Unit and Core Unit A M B C L D K E J F I G H System ChassisFront View Figure 1-2 Front View System OverviewDE C F B A Top ViewFigure 1-3 shows the components within the Main Chassis Figure 1-3. Main Chassis 1-6 System OverviewSystem Overview Right Side ViewFigure 1-4 shows the system right side features Figure 1-4. 1080Xd Right Side ViewFigure 1-5. CELLV Board 1-8 System Overview Internal ViewFigure 1-5 shows internal views of CELLV Board features PCI-X Core Module Main ComponentsItanium 2 Processors System MemoryPartitioning Service Processor BoardPower/Status LEDs System FunctionsServer Management Chipset and Crossbar Switch1-12 System Overview ExpansionFigure 1-6. Express5800/1080Xd System Configuration I t ani um2Optional PCIX Unit CELLV BoardCPUs MemoryPeripheral Devices SecuritySystem Operation Setting Up the Server Starting Up the System Shutting Down the SystemRebooting the System Booting the OS Using the DVD-ROM Drive Using an Optional Tape DriveSetting Up the Server 6. Close and lock the rear server door Starting Up the System System Operation Figure 2-4. PCIX Unit AC Power Circuit BreakerFigure 2-5. AC Power Switch 9. Press Esc Figure 2-7. System Startup Screen System Operation Shutting Down the System 2. Check that the DC power is off. The SP console displays a “power off” message see Figures 2-8, 2-9, and Dump Using Exception ProceduresCold Reset Restart Power On ResetOS Boot from the EFI Boot Manager Booting the OSOS Boot from Boot Manager EFI Shell 2-14 System Operation EFI Shell CommandsTable 2-1. EFI Shell Commands Description Table 2-1. EFI Shell Commands continuedCommand System OperationOS Boot from EFI Shell EFI Device Path Notes for OS InstallationChecking Failure Removing a Disc from the DVD-ROM Drive Using the DVD-ROM DriveInserting a Disc in the DVD-ROM Drive Environmental DAT Specifications Using an Optional Tape DriveWrite Protection DAT Cartridge LabelsDAT Cartridge Insertion and Removal SP Command Reference Service ProcessorSP Console OS Console Virtual SOP SP Command Console SP Console Connections SP ConsoleConsole Operations Console Status and Login Authentication3-4 Service Processor See Figure 3-2 for a diagram of using console modesTable 3-2. Login Account and Password Defaults Service Processor Figure 3-2. Express5800/1080Xd Console Mode Operations3-6 Service Processor Login and Main MenuTable 3-3. Login and Main Menu Screen Description Table 3-4. Login and Main Menu Screen ReferencesTable 3-5. Main Menu Login Events and Operations Service ProcessorOS BIOS Console Table 3-9. Virtual SOP Screen Virtual SOPTable 3-8. OS BIOS Console Events and Operations Service Processort t t t t t t t t t t t t t t t t t t t t t t t t t t t t t t Partition State Display3-10 Service Processor xx N sssssssssssssss ccccccDisplay Service ProcessorTable 3-11. Reference to Partition State Display cont’d ReferenceSP Command Console Buffer SP Command ConsoleSP Message Header SP Command Prompt3-14 Service Processor SP Command ListTable 3-16. System Control Commands Figure 3-4. System State Transitions and System Control CommandsCommand Name Table 3-17. Configuration CommandTable 3-18. Normal Mode Commands Service Processor3-16 Service Processor SP Command ReferenceFunction CM Change Command ModeExecution Function DF Shut Down System Power overrideExecution Function DL Display SP LogsExecution Reference 3-20 Service ProcessorTable 3-23. DL Screen cont’d Screen ImageScreen Image Service ProcessorDL Screen cont’d Table 3-24. DL Screen ReferencesDescription 3-22 Service ProcessorTable 3-24. DL Screen References cont’d ReferenceFunction DN Shut Down System PowerExecution Description 3-24 Service ProcessorTable 3-26. DN Screen References ReferenceFunction DP System DumpExecution Maintenance mode DT SP Date and Time3-26 Service Processor Note The DT command can be executed in Normal mode orMaintenance mode EN Environmental InformationService Processor Note The EN command can be executed in Normal mode orReference 3-28 Service ProcessorEN Screen cont’d Screen ImageScreen Image Service ProcessorEN Screen cont’d Table 3-31. EN Screen ReferencesDescription 3-30 Service ProcessorTable 3-31. EN Screen References cont’d ReferenceMaintenance mode FV Firmware VersionsService Processor Note The FV command can be executed in Normal mode orFunction HC Hardware Configuration3-32 Service Processor Executionarg2 Table 3-35. HC SubcommandsService Processor arg1arg2 Table 3-35. HC Subcommands cont’d3-34 Service Processor arg1arg2 Table 3-35. HC Subcommands cont’dService Processor arg1arg2 Table 3-35. HC Subcommands cont’d3-36 Service Processor arg1arg2 Table 3-35. HC Subcommands cont’dService Processor arg1arg2 Table 3-35. HC Subcommands cont’d3-38 Service Processor arg1arg2 Table 3-35. HC Subcommands cont’dService Processor arg1arg2 Table 3-35. HC Subcommands cont’d3-40 Service Processor arg1arg2 Table 3-35. HC Subcommands cont’dService Processor arg1arg2 Table 3-35. HC Subcommands cont’d3-42 Service Processor arg1arg2 Table 3-35. HC Subcommands cont’dService Processor arg1arg2 Table 3-35. HC Subcommands cont’d3-44 Service Processor arg1arg2 Table 3-35. HC Subcommands cont’dService Processor arg1arg1 Table 3-35. HC Subcommands cont’d3-46 Service Processor Table 3-36. HC State Display StringsDisplayed String Service ProcessorTable 3-36. HC State Display Strings cont’d Table 3-37. HC Help ScreenReference 3-48 Service ProcessorTable 3-38. HC ALL Display Screen Screen ImageReference Service ProcessorTable 3-38. HC ALL Display Screen cont’d Screen ImageReference 3-50 Service ProcessorTable 3-38. HC ALL Display Screen cont’d Screen ImageDescription Service ProcessorTable 3-39. HC ALL Display Screen References ReferenceMaintenance mode HE Help3-52 Service Processor Note The HE command can be executed in Normal mode orMaintenance mode ML Message LogService Processor Note The ML command can be executed in Normal mode orReference 3-54 Service ProcessorE Displays the command termination message Table 3-42. ML Display Screen ReferencesMaintenance mode PC Power CycleService Processor Note The PC command can be executed in Normal mode orDescription 3-56 Service ProcessorTable 3-44. PC Display Screen References ReferenceMaintenance mode RS Cold Reset SystemService Processor Note The RS command can be executed in Normal mode orFunction UP Bring Up SystemExecution HBB Configuration Submenu Precaution BIOS SetupSetup Overview Menu Tree Menu Options and Settings BIOS Virtual DIP Switch PCI Online Maintenance PCI Hot PlugSome Setting Errors Exist Setup OverviewWhat is Setup? When You Should Change the SettingsThe system will wait for a key entry. Press the F2 key to start Setup Settings of CMOS and/or NVRAM Are ClearedAdding or Deleting a Boot Device The Host Bus Bridge Configuration Has Changed Starting SetupThe BIOS Version Has Changed Figure 4-1. Screen Description BIOS Setup Screen DescriptionTo configure Setup, use the keys on the bottom portion of the screen Menu Tree Main Menu Overview Advanced Menu Overview Security Menu Overview System Hardware Menu Overview Console Type Flow Control Serial Port Baud Rate Console Type BIOS SetupConsole Redirection Serial Port Select Debug Port Select System Serial Port Baud RateExit Menu Overview Figure 4-2. Main Menu BIOS Setup Menu Options and SettingsMain Menu Option 4-14 BIOS SetupTable 4-3. Main Menu Options MenuFigure 4-3. Advanced Menu BIOS Setup Advanced MenuOption 4-16 BIOS SetupTable 4-4. Advanced Menu Options MenuHandling the undetected VGA Advanced SubmenuError code is displayed on the LCD Code9009 Figure 4-5. Peripheral Configuration Submenu 4-18 BIOS Setup Peripheral Configuration SubmenuOption Table 4-6. Peripheral Configuration SubmenuBIOS Setup MenuFigure 4-6. Monitoring Configuration Submenu 4-20 BIOS Setup Monitoring Configuration SubmenuOption Table 4-7. Monitoring Configuration SubmenuBIOS Setup MenuFigure 4-7. Option ROM Submenu 4-22 BIOS Setup Option ROM SubmenuOption BIOS SetupTable 4-8. Option ROM Submenu MenuFigure 4-8. Extended PCI Slot Submenu 4-24 BIOS Setup Extended PCI Slot SubmenuDefault value of an Option ROM Scan of the extended PCI slot Procedure when a video card is installed Main Numlock SubmenuFigure 4-9. Numlock Submenu BIOS Setup Option 4-28 BIOS SetupTable 4-11. Numlock Submenu MenuSecurity Security MenuFigure 4-10. Security Menu BIOS Setup Description 4-30 BIOS SetupTable 4-12. Security Menu OptionFigure 4-11. System Hardware Menu BIOS Setup System Hardware MenuDescription 4-32 BIOS SetupTable 4-13. System Hardware Menu OptionFigure 4-12. HBB Configuration Submenu BIOS Setup HBB Configuration SubmenuDescription Table 4-14. HBB Configuration Submenu4-34 BIOS Setup OptionFigure 4-13. PCI Bus Parity Error Assert Submenu BIOS Setup PCI Bus Parity Error Assert SubmenuDescription Table 4-15. PCI Bus Parity Error Assert Submenu4-36 BIOS Setup OptionFigure 4-14. Master Latency Timer Submenu BIOS Setup Master Latency Timer SubmenuDescription Table 4-16. Master Latency Timer Submenu4-38 BIOS Setup OptionFigure 4-15. Multi Transaction Timer Submenu BIOS Setup Multi Transaction Timer SubmenuDescription Table 4-17. Multi Transaction Timer Submenu4-40 BIOS Setup OptionFigure 4-16. Low MMIO Configuration Submenu BIOS Setup Low MMIO Configuration Submenu4-42 BIOS Setup Table 4-18. Low MMIO Configuration SubmenuFigure 4-17. High MMIO Configuration Submenu BIOS Setup High MMIO Configuration Submenu4-44 BIOS Setup Table 4-19. High MMIO Configuration SubmenuFigure 4-18. IO Space Configuration Submenu BIOS Setup IO Space Configuration Submenu4-46 BIOS Setup Table 4-20. IO Space Configuration SubmenuFigure 4-19. PCI Bus Configuration Submenu BIOS Setup PCI Bus Configuration SubmenuDescription Table 4-21. PCI Bus Configuration Submenu4-48 BIOS Setup OptionFigure 4-20. Console Redirection Submenu BIOS Setup Console Redirection SubmenuDescription 4-50 BIOS SetupTable 4-22. Console Redirection Submenu OptionConsole Redirection - System Serial Port Description 4-52 BIOS SetupTable 4-23. Console Redirection - System Serial Port Submenu OptionFigure 4-22. Console Redirection - Serial Port 1 Submenu BIOS Setup Console Redirection - Serial PortDescription 4-54 BIOS SetupTable 4-24. Console Redirection - Serial Port 1 Submenu OptionTable 4-25. Shrink Total Number of Interrupt Vectors Submenu Shrink Total Number of Interrupt Vectors SubmenuBIOS Setup Figure 4-23. Shrink Total Number of Interrupt Vectors SubmenuTable 4-26. Memory Mapped I/O 4GB Submenu Memory Mapped I/O 4GB Submenu4-56 BIOS Setup Figure 4-24. Memory Mapped I/O 4GB SubmenuFigure 4-25. Exit Menu BIOS Setup Exit MenuDescription 4-58 BIOS SetupTable 4-27. Exit Menu OptionBIOS Setup BIOS Virtual DIP SwitchWhat is BIOS Virtual DIP Switch? Table 4-28. Virtual DIP Switch Setting ValuePreparing the Resources PCI Online Maintenance PCI Hot PlugAvailable PCI Online Maintenance Function If an expanded PCI Gap was specified If a Reboot OccursI/O Space PCI Bus NumberIf a reboot occurred due to incorrect resource values Figure 4-26. HBB Configuration Submenu Example BIOS Setup HBB Configuration Submenu PrecautionPage Identifying PCI Slots in the Core Module I/O Board InstallationInstalling a Board in the Core Module Installing a Board in the PCIX UnitFigure 5-1. PCI Slots in the Core Module Identifying PCI Slots in the Core Module5-2 I/O Board Installation Slot Number I/O Board InstallationTable 5-1. PCI Slot Allocation in the Core Module Figure 5-2. PCI Slots and Bus Groups in the Core ModuleFigure 5-3. PCI Slots in the PCIX Unit Identifying PCI Slots in the PCIX Unit5-4 I/O Board Installation Figure 5-4. PCI Slots and Bus Groups in the PCIX Unit I/O Board InstallationConfiguration Table 5-2. PCI Slot Allocation in the PCIX UnitSelecting a Slot Figure 5-5. Front Stabilizer and Main Chassis Door Installing a Board in the Core ModuleI/O Board Installation 2. Pull open the Main Chassis door from the right edge see Figure3. Access the Main Chassis as follows 5. Access the board slots 6. Install the board in the slot 11. Connect any I/O board cable at the rear of the server I/O Board Installation5-12 I/O Board Installation Installing a Board in the PCIX UnitA Stabilizer B PCIX Unit Front Bezel I/O Board InstallationFigure 5-10. Stabilizer and PCIX Unit Front Bezel Figure 5-11. PCIX Unit Screws5-14 I/O Board Installation 5. Lift and swing the PCIX unit PCI slot access cover open see FigureFigure 5-12 PCIX Unit PCI Slot Access Cover Carefully remove the slot cover 6. Install the board in the appropriate slot7. Replace the access cover see Figure I/O Board Installation10. Connect any I/O board cable at the rear of the server Solving Simple Problems Troubleshooting the System Problem Solving6-2 Problem Solving Solving Simple ProblemsTable 6-1. Checklist for Solving General Problems Corrective Action Table 6-1. Checklist for Solving General Problems cont’dProblem Solving Symptom6-4 Problem Solving Troubleshooting the SystemMain Chassis DVD-ROM Drive Tape Drive FDD Technical SpecificationsSpecification Main ChassisTable A-1. Main Chassis Technical Specifications A-2 Technical SpecificationsTechnical Specifications A-3 DVD-ROM DriveTable A-1. Main Chassis Technical Specifications cont’d Table A-2. DVD-ROM Drive Technical SpecificationsSpecification Tape DriveTable A-3. Optional Tape Drive Technical Specifications A-4 Technical SpecificationsSpecification Table A-4. Optional FDD Technical SpecificationsTechnical Specifications A-5 Page Memory Configurations DIMM Installation Memory UpgradesB-2 Memory Upgrade Memory ConfigurationsMMC #1 DIMM InstallationFigure B-1. CELLV Board DIMM Installation Locations Memory Upgrade B-3Slot Location Table B-1. DIMM InstallationB-4 Memory Upgrade InstallationInstalling Microsoft Windows Creating a Mirrored Drive of Windows Windows 2003 InstallationInstalling Microsoft Windows Creating a Mirrored Drive of Windows DISKPART list partition C-4 Windows 2003 InstallationC\ diskpart DISKPART select diskDISKPART select partition Windows 2003 Installation C-5Note Make sure you are at the root directory C\ DISKPART select diskC-6 Windows 2003 Installation 11. Manage the EFI boot menuReboot the partition Enter the EFI boot manager Change the boot order toWindows 2003 Installation C-7 12. Test the process C\ bootcfgTest the clone by selecting it then booting If the mirrored drive boots OK, then the process is completePage Index-1 IndexIndex-2 Index-3 Index-4