Pressure Compensation and Temperature Compensation
Figure
|
|
|
|
|
| Class: Calibration Object (0x65) |
|
|
|
|
|
| Instance: 1 |
|
| Set pressure unit |
|
| ||
|
|
|
| Attribute ID: 29 | ||
|
|
|
| |||
|
|
|
|
|
| Value: See Table |
(1) Pressure measurement unit must |
|
|
|
| Service: Set | |
be configured to match pressure unit |
|
|
|
|
| |
used by external device. See |
|
|
|
|
| |
|
|
|
| Class: Calibration Object (0x65) | ||
Section 6.3. |
|
|
|
|
| |
|
|
|
|
| Instance: 1 | |
(2) See Section 9.4. |
| Set flow calibration |
|
| ||
|
|
| Attribute ID: 32 | |||
|
| pressure |
|
| ||
|
|
|
| Data type: REAL | ||
|
|
|
|
|
| |
|
|
|
|
|
| Service: Set |
|
|
|
|
|
|
|
|
|
|
|
|
| Class: Calibration Object (0x65) |
|
|
|
|
|
| Instance: 1 |
|
| Set flow factor | ||||
|
|
|
| Attribute ID: 30 | ||
|
|
| ||||
|
|
|
|
|
| Data type: REAL |
|
|
|
|
|
| Service: Set |
|
|
|
|
|
|
|
|
|
|
|
|
| Class: Calibration Object (0x65) |
|
|
|
|
|
| Instance: 1 |
|
| Set density factor |
|
| ||
|
|
|
| Attribute ID: 31 | ||
|
|
|
| |||
|
|
|
|
|
| Data type: REAL |
|
|
|
|
|
| Service: Set |
|
|
|
|
|
|
|
|
|
|
|
|
| Class: Calibration Object (0x65) |
|
|
|
|
|
| Instance: 1 |
|
|
|
|
|
| Attribute ID: 27 |
|
| Enable pressure |
|
| ||
|
|
|
| Data type: BOOL | ||
|
| compensation |
|
| ||
|
|
|
| Value: | ||
|
|
|
|
|
| · 0 = disabled |
|
|
|
|
|
| · 1 = enabled |
|
|
|
|
|
|
|
|
|
|
|
| Use static |
| |||||||
|
|
|
|
| pressure value? |
|
|
|
|
|
|
| |
| No |
|
|
|
| Yes |
|
|
|
| |||
|
|
|
|
|
|
|
|
| Class: Calibration Object (0x65) | ||||
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| Instance: 1 |
Set up output |
| Set static value |
|
| |||||||||
|
|
| Attribute ID: 28 | ||||||||||
assembly(2) |
|
|
| ||||||||||
|
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
| Data type: REAL |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| Service: Set |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Compensation
Measurement Performance
Troubleshooting
9.3External temperature compensation
External temperature compensation can be used with the petroleum measurement application or the enhanced density application.
Note: The external temperature value is used only for calculation of the derived variable in enhanced density applications or the CTL value in petroleum measurement applications. The temperature value from the sensor is used for all other calculations that require a temperature value.
Defaults
Configuration and Use Manual | 85 |