Set Menu SET, Menu Options | High End Systems Technobeam manual

Set Menu (SET)

The Set menu allows you to change the control method from a fixture number to a DMX start channel or vice versa, and either set all factory options to their default settings or change the factory options individually. The procedures below are listed in the order that they appear in the menu map.

Setting Factory Defaults (FACT)

Technobeam-i fixtures are shipped from the factory with the following preset options set to the following defaults:

•Pan/tilt swap = off

•pan invert = off

•tilt invert = off

•preset playback = off

•LED display = on and bright

•LED display invert = off

•lamp hour warning = off

To return all preset options to their factory defaults settings:

5. Press and hold the <Menu> button until “ADDR” appears on the LED display.

6.Using the <Up> and <Down> arrow buttons, scroll to the “SET” menu

and press the <Enter> button to select the “SET” menu.

7. Using the <Up> and <Down> arrow buttons, scroll to the “FACT” menu. (This will be the first menu displayed.) Press the <Enter> button to select the “FACT” menu.

8.Using the <Up> and <Down> arrow buttons, choose “ON” to set the factory option defaults on and press the <Enter> button to select the desired option.*

*Note	Although “OFF” is an available option in the FACT menu,
	selecting the “OFF” option will have no effect on the
	individual preset values. To change the value of any of
	the individual presets listed above, you must access
	each preset’s corresponding menu item. When you
	change any of the preset default values individually, this
	menu item will automatically be turned off.

Technobeam® User Manual

Menu Options 3-11

Image 80

High End Systems Technobeam manual Set Menu SET, Setting Factory Defaults Fact, Menu Options

Contents

Austin, TX 78758 USA 512 60600115 Version Page Page Page Trademarks Declaration of Conformity Important Safety Information Warranty Information Freight Table of Contents Appendix B Factory-Installed Wheels Table of Figures Laser aiming device circuit board Table of Tables Xii Introduction Servicing Your Fixture Page Page Page Page Page Page Features Introduction Intro-2Introduction Construction Symbols Document Conventions Contacting High End Systems Intro-4Introduction Preparing to Install Your Fixture Specifications Vigtig Sikkerhedsinformation Danmark Important Power Cord Information U.K. OnlyLAD Safety Standards Electromagnetic Standards Dichroic, Litho and Effects SpecificationsSafety Standards Optional Accessories Environmental SpecificationsDMX Data Cabling Controllers Unpacking the Fixture Unpacking the FixtureSave the Shipping Materials Important Power Cord Cap Information U.K. Only Installing the Power Cord CapInspecting the Contents Installing the Yoke Installing the Yoke Installing the yoke on the fixture Setting the Fixture Voltage 10Setting the Fixture Voltage Setting the Fixture Voltage Setting the Beam Angle 12Setting the Beam Angle Setting the Beam Angle Hint 14Setting the Beam Angle Away from Chapter Setting Up Your Fixture Powering On the Fixture Powering On the FixtureHoming the Fixture LED Display Status LEDs Status LEDs What is DMX 512 Protocol? Overview of Controller OperationWhat Kind of Cabling Should You Use? Overview of Controller Operation Constructing Cabling Terminators Setting up the Link Constructing a data cable terminator Linking the Fixtures to Controller Mounting the Fixture Mounting the Fixture Standing the Fixture on its End Handles Mounting the Fixture on a Truss or Other Support System Use a locking washer when attaching a fixture to a truss 10Mounting the Fixture Handle Hanging the Fixture Straight Down 12Mounting the Fixture Fixture Types Configuring the FixtureConfiguring the Fixture 14Configuring the Fixture Selecting a Control MethodDMX Start Channel Control Method Fixture Number Control Method Assigning a Fixture Address Channel Range 16Configuring the Fixture Determining the Unique DMX Start Channel Determining the Unique Fixture Number Wasted DMX Channels Upgrading Software 18Upgrading Software Crossloading Software Upgrading Software Troubleshooting 20Troubleshooting Troubleshooting Lamp shuts off 22Troubleshooting Lithos or dichroic filters are cracking Troubleshooting DMX Data 24Troubleshooting Addr Lost Menu Error MessagesBoot Diff 26Troubleshooting Emem AckEmem message Erse Flsh Link Empty LampLink Busy 28Troubleshooting Over TempPrst Lost Pgrm Time Chapter Using the Menus Accessing the Menu System Menu System OverviewNavigation Buttons Menu System Overview Menu Map Menu Map Mechanically home the fixture, then press any Than the last channel in the viewing fixture’s Open WSP Rand Dlay 10Menu Options Menu OptionsAddress Menu Addr Menu Options Setting Factory Defaults FactSet Menu SET Swapping Pan and Tilt Swap Inverting Tilt T/INInverting Pan P/IN 12Menu Options Changing the Control Method Chnl Changing the Display Output DsplInverting LED Characters D/IN 14Menu Options Setting the Lamp Warning Message LmplChanging the Lens Setting Lens Mode Menu Mode Setting the Fixture Type and Protocol Type Setting the User Type User 16Menu Options Copying User Presets Prst 18Menu Options Copying User Settings SettCopying User Presets and Settings ALL Crossloading Fixture Software XLD Test Menu Test Homing the Fixture HomeTurning the Lamp On or Off Lamp 20Menu Options Copying the Boot Code Boot Performing Self Tests Self Placing the Fixture in Setup Mode S/UP Testing the LED Display DispInformation Menu Info 22Menu Options Viewing the Current Fixture Hours F/HR Viewing the Logic Board Temperature TempViewing the Current Lamp Hours L/HR Viewing the Number of Current Lamp Strikes L/ST Viewing the Current Software Version VERViewing DMX Status and Construct Values Fixt 24Menu Options Menu Options 26Menu Options Viewing DMX Data for Another Device DataViewing Sensor Information Sens Resetting Fixture Hours F/RS Resetting Lamp Hours L/RS 28Menu Options Preset Menu PrstSetting Preset Playback Play Copying an On-Board Memory Scene Copy Capturing a Preset Scene CaptEditing or Creating an On-Board Memory Scene Edit Enabling the Preset Default Dflt 30Menu Options Chapter Preset Programming What is a Scene? Programming OverviewStand-alone Operation vs. a Controller Macros Preset Playback Options General InformationSubject to Change Enter and Menu Keys Orienting and Powering On the Fixture Creating a SceneTurning on the Lamp Selecting Constructs and Values Opening the Shutter Making sure the shutter is open Selecting Color Wheel Constructs Focusing on a LithoPositioning the Mirror Refocusing the Fixture Setting a Delay TimeSelecting a Color Wheel Pause Time Selecting Effects Constructs Creating Scene Playing Back Both Scenes Synchronizing Preset Playback Setting Up the Fixtures 10Synchronizing Preset Playback Adding Fixtures Capturing PresetsCapturing Presets 12Capturing Presets Chapter Using the Laser Aiming Device LAD Safety Precautions Safety Precautions Using the Laser Aiming Device OverviewRecommended Laser Operation Intended Audience Laser aperture Controlling the Laser Menu Control of the LaserDMX Control of the Laser Controlling the Laser Laser is out of position Laser gradually loses powerEmission Indicator LED OFF, Laser OFF Emission Indicator LED ON, Laser OFF LAD wiring connections Maintenance MaintenanceLaser ON, Emission Indicator LED OFF Chapter Servicing Your Fixture Replacing Fuses PrecautionsPrecautions Fuse Failure Symptoms Replacing Fuses Replacing Wheel Components SpecificationsReplacing Wheel Components Reference Drawing Replacing Dichroics in the Color Wheel Coated Uncoated Replacing Lithos in the Rotating Litho Wheel Removing a Rotating Litho or Rotating Effect Cleaning the Litho Removing a Static Litho Litho Installation Instructions Replacing a Static Litho Replacing a Rotating Litho or Effect 10Replacing Wheel Components Replacing the Lamp Replacing the LampReplacing a Custom Litho 14. Removing the lamp assembly from the fixture 12Replacing the Lamp Avoid touching any part of your skin to Optimizing the Lamp 14Replacing the Lamp Cleaning the Internal Components Resetting Lamp Hours Cleaning the Door Vents Cleaning the Lenses and Mirrors16Cleaning the Internal Components Opening the Fixture Lens tube Latches 18Cleaning the Internal Components 22. Clean both sides of the hot mirror glass Safety Precautions Technobeam Laser Aiming Device Live Components 20Technobeam Laser Aiming Device Alignment Procedure 22Technobeam Laser Aiming Device Technobeam Laser Aiming Device 24Technobeam Laser Aiming Device Ruler or a piece of string, as shown in Figure If you have difficulty aligning the laser or turning 26Technobeam Laser Aiming Device General Information Rounding ConventionsBit Control DMX Protocols A-1 Forward and Reverse Spins MSpeed vs. Fast ChangesRamp Open, Snap Shut 2DMX Protocols Technobeam Protocol DMX Protocols A-3 4DMX Protocols DMX Protocols A-5 Litho wheel functions 6DMX Protocols Effects position Technobeam-i Protocol DMX Protocols A-7 8DMX Protocols Table A-2. Technobeam-i DMX Protocol DMX Protocols A-9 F8-FF 10DMX Protocols DMX Protocols A-11 E6-FF MSpeed Movement Times 12DMX Protocols DMX Protocols A-13 Table A-3. MSpeed Movement Times 14DMX Protocols Macro Channel Assignments DMX Protocols A-15 Fixture Number to DMX Start Channel 16DMX Protocols Factory-Installed Wheels Technobeam Wheels Technobeam color wheel Important Safety Information English Version Appendice C Important Informations DE Sécurité Anhang C Wichtige Hinweise Für Ihre Sicherheit Warnung ZUM Schutz VOR Brandgefahr Appendice C Importanti Informazioni Di Sicurezza Warnung ZUM Schutz VOR Verletzungen Apéndice C Información Importante De Seguridad Avvertenza PER Prevenire LE Scosse Elettriche Vigtig Sikkerhedsinformation Danmark Index Index-ii Index-iii Index-iv