Payload Loopback, Plb | Paradyne CSU, DSU, 9126-II, 9128-II specification

8. Troubleshooting

Payload Loopback

The Payload Loopback (PLB) loops the information received on the selected interface back to the network after it has passed through the receive and transmit framing section of the device. Use the PLB to determine whether the problem is with the T1 facility or in the circuitry of the remote device.

Main Menu → Test→ Network Physical Tests

Other	All
T1

Framer

PLB

The T1

Interface	1s
Interface

Interface

97-15337

CAUTION:

This test may affect operation of frame relay PVCs assigned to the selected interface. While in loopback, the frame relay link will be down so any IP data being sent while this test is active will be disrupted.

A PLB cannot be started when one of the following tests is active:

Line Loopback, Repeater Loopback, Send Remote Line Loopback, or an active Monitor Pattern on this network interface.

Payload or Repeater Loopback on any other T1 interface with DS0s assigned to this network interface.

Send Pattern Test on this network interface or any synchronous data port (Port

TUse set to Synchronous) assigned to this interface.

Send V.54 or FT1 Loopback, or Data Channel Loopback on any synchronous data port (Port Use set to Synchronous) and assigned to this network interface.

8-28

September 2002

9128-A2-GB20-80

Image 292

Paradyne CSU, DSU, 9126-II, 9128-II manual Payload Loopback, Plb

Contents

FrameSaver SLV Warranty, Sales, Service, and Training Information Copyright 2002 Paradyne Corporation All rights reservedDocument Feedback Trademarks Contents Configuration Options ConfigurationTProceduresSeptember Configuring the FrameSaver SLV Router Iii Security and Logins Operation and Maintenance Troubleshooting Lamp Test Setting Up NetScout Manager Plus for FrameSaver Devices Setting Up Network Health for FrameSaver DevicesMenu HierarchyT Vii Router CLI TCommands, Codes, and Designations Snmp MIBs and Traps, and Rmon Alarm DefaultsViii Router Command Line Summaries and Shortcuts Connectors, Cables, and Pin Assignments Technical Specifications Equipment List Index Document Organization Purpose and Intended AudienceSection Description Xii Section Description Xiii Product-Related DocumentsDocument Number Document Title Conventions Used Xiv About the FrameSaver SLV System Overview CSU/DSU-Specific Features Router-Specific Features About the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set Maximum Number of PVCs and Management PVCs Supported FrameSaver SLV Feature RouterThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaverTSLV 9126-II and 9128-II Features Additional FrameSaver SLV 9128-II Features FrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Procedure Logging On If your login was Hen Main Menu Select Screen Work Areas Screen Format Description Keyboard Keys Navigating the ScreensPress Function Keys For the screen Select Function Press Enter to Switching Between Screen Areas Selecting from a Menu Selecting a Field Screen ContentsEntering Information Navigating the Router’s CLI CLI Keyboard Keys Configuration Procedures Basic Configuration Configuration Menu Isdn Configuration Option Areas Configuration Option Area Description Accessing and Displaying Configuration Options Main Menu → Configuration Changing Configuration Options Configuration → PVC Connections Saving Configuration Options Configuration Options Configuration Options Main Menu → Easy Install Using the Easy Install FeatureEasy Install Screen Example Using RIP with FrameSaver SLV CSU/DSUs Configuration → Data Ports→ Dlci Records Main Menu → Control→ System Information Entering System Information and Setting the System ClockIf the selection is Enter Setting Up the Modem Setting Up Call Directories for Trap Dial-OutMain Menu → Control→ Modem Call Directories Valid characters include For Setting Up to Use the Modem PassThru Feature Main Menu → Auto-Configuration Setting Up Auto-ConfigurationAuto-Configuration Screen Example Selecting a Frame Relay Discovery Mode Main Menu → Auto-Configuration→Frame Relay Discovery ModeDiscovery Mode Configuration Description Only applies to models with Discovery Mode Configuration Description Automatically Removing a Circuit Setting Up the DBM Physical Interface Setting Up Dial BackupMain Menu → Configuration → Isdn → Physical Setting Up Automatic Backup Configuration If you select Then Following prompt When Appears If you select Remove Alternate DestinationsFrom PVCs Delete unused For Originating a Backup Call For Answering a Backup Call Main Menu → Configuration → Isdn → Link ProfilesModifying Isdn Link Profiles Restricting Automatic Backup and Configuring Backup Timers Main Menu → Configuration → Auto-Backup Criteria Configuring the DBM Interface to Send Snmp Traps Assigning DLCIs to a Backup Group PVC Backup Over the Network Interface Setting Up Back-to-Back OperationChanging Operating Mode Main Menu → Control→ Change Operating Mode Configuration Option Tables Configuring the Overall System Configuring Frame Relay and LMI for the System CSU/DSUsMain Menu → Configuration → System → Frame Relay and LMI System Frame Relay and LMI Options 1 System Frame Relay and LMI Options 2 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Configuring Class of Service Definitions Field Setting After RfcCodePoints Selected Class of Service Definitions Class of Svc NameMeasure Latency & Availability Code Points Assigned Code Point Definitions Code Point DefinitionsCode Pnt Name Configuring Service Level Verification Options Service Level Verification Options 1SLV Type Available Settings Standard, COS 1-COS SLV Sample Interval secs Service Level Verification Options 2 Dlci Down on SLV TimeoutSLV Timeout Error Event Threshold SLV Timeout Clearing Event Threshold SLV Latency Clearing Event Threshold Service Level Verification Options 3SLV Packet Size bytes Configuring General System Options Main Menu → Configuration → System→ GeneralTest Timeout General System Options 1 General System Options 2 System Alarm Relay General System Options 3 Configuring Physical Interfaces Configuring the Network InterfaceMain Menu → Configuration → Network→ Physical Network Physical Interface Options 1 Line Build Out LBO Possible Settings 0.0, -7.5, -15 Network Physical Interface Options 2Bit Stuffing Transmit Timing Network Initiated Dclb Possible Settings Disable, V.54&ANSI Network Physical Interface Options 3Network Initiated PLB Ansi Performance Report Messages Network Physical Interface Options 4 Circuit Identifier Configuring a User Data Port CSU/DSUs Main Menu → Configuration → Data Ports→ PhysicalPort Use Possible Settings Frame Relay, Synchronous Data Data Port Physical Interface Options 1 Data Port Physical Interface Options 2 Max Port Rate KbpsPort Base Rate Kbps Transmit Clock Source Monitor RTS Control Data Port Physical Interface Options 3Monitor DTR Port DTE Initiated Loopbacks Data Port Physical Interface Options 4Invert Transmit and Receive Data Action on Network Yellow Alarm Data Port Physical Interface Options 5 Configuring the DSX-1 Interface Main Menu → Configuration → DSX-1DSX-1 Physical Interface Options 1 Interface Status DSX-1 Physical Interface Options 2 Send All Ones on DSX-1 Failure Configuring the Isdn DBM Interface Service Profile ID Spid 1 orIsdn BRI DBM Physical Interface Options Local Phone Number 1 or 10. Isdn PRI DBM Physical Interface Options 1 Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESSLocal Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Setting Up Isdn Link Profiles Main Menu → Configuration → Isdn → Isdn Link Profiles11. Isdn Link Profile Options 1 Link Name 11. Isdn Link Profile Options 2 Outbound Phone NumberInbound Calling ID 1 or Maximum Link Rate Kbps Assigning Time Slots/Cross Connections 11. Isdn Link Profile Options 3Caller Identification Method Alternate Outbound Phone Number Frame Relay Network Time Slot Assignment Screen Example Assigning Frame Relay Time Slots to the Network InterfaceValue Meaning Time Slot Assignment Rule Assigning DSX-1 Time Slots to the Network InterfaceNtt DSX-1 to Network Time Slot Assignment Screen Example Ime Slot Assignment Rules DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Synchronous Data Port Assignment Screen Example Sync Data Port Assignment Clearing Assignments Physical Interface Options 13. Interface Frame Relay Options 1 Configuring Frame Relay for an InterfaceLMI 13. Interface Frame Relay Options 2 Traffic PolicingLMI Parameters Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 3 14. Dlci Record Options 1 Manually Configuring Dlci RecordsDlci Number CIR bps 14. Dlci Record Options 2Committed Burst Size Bc Bits 14. Dlci Record Options 3 Excess Burst Size BitsDlci Priority Outbound Management Priority Backup Group Possible Settings A, B, C, . . . Z, None 14. Dlci Record Options 4 Configuring PVC Connections Main Menu → Configuration → PVC Connections15. PVC Connection Options 1 Source Dlci 15. PVC Connection Options 2 Source EdlciPrimary Destination Link Primary Destination Dlci 15. PVC Connection Options 3 Primary Destination EdlciAlternate Destination Link Alternate Destination Dlci 15. PVC Connection Options 4 Alternate Destination Edlci Configuring the IP Path List Main Menu → Configuration → IP Path List Static16. IP Path List Enter IP Address press ESC to abort ... FWD No Setting Up Management and Communication Options Configuring Node IP Information 17. Node IP Options 1 TS Access Management Link 17. Node IP Options 2 17. Node IP Options 3 TS Management Snmp Validation Configuring Management PVCs 18. Management PVC Options 1 Payload Managed 18. Management PVC Options 2Set DE 18. Management PVC Options 3 Primary Dlci 18. Management PVC Options 4 Primary Edlci Alternate Dlci 18. Management PVC Options 5Alternate Edlci 18. Management PVC Options 6 Encapsulation Configuring General Snmp Management Name 1 Access19. General Snmp Management Options 1 Snmp Management Name 2 Access Configuring Telnet and/or FTP Session Support19. General Snmp Management Options 2 20. Telnet and FTP Session Options 1 Telnet Login RequiredTelnet Session 20. Telnet and FTP Session Options 2 Configuring Snmp NMS Security 21. Snmp NMS Security Options 1NMS IP Validation Number of Managers 21. Snmp NMS Security Options 2 Configuring Snmp Traps and Trap Dial-Out22. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 22. Snmp Traps and Trap Dial-Out Options 3 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps Possible Settings Network, Ports, DBM, All, None 22. Snmp Traps and Trap Dial-Out Options 4Dlci Traps on Interfaces Filter Selection Field Rmon Traps Dial-Out Delay TIme Min 22. Snmp Traps and Trap Dial-Out Options 5Trap Dial-Out Trap Disconnect 22. Snmp Traps and Trap Dial-Out Options 6 Alternate Dial-Out DirectoryLatency Traps IP SLV Availability Traps Configuring Ethernet Management 23. Ethernet Management Options 1 23. Ethernet Management Options 2 Proxy ARP 24. Communication Port Options 1 Configuring the Communication PortCharacter Length Login Required 24. Communication Port Options 2Parity Stop Bits 24. Communication Port Options 3 24. Communication Port Options 4 RIP Configuring the Modem Port 10024. Communication Port Options 5 25. Modem Port Options 1 101 25. Modem Port Options 2 102 25. Modem Port Options 3 103 25. Modem Port Options 4 Configuring the Criteria for Automatic Backup Main Menu → Configuration → Auto Backup Criteria26. Auto Backup Criteria Options 1 104 26. Auto Backup Criteria Options 2 When Auto Backup AllowedBackup Allowed Day From nnnn Backup Allowed Day To nnnn 106 Configuring the FrameSaver SLV Router Network Interface FrameSaver SLV Router OverviewEthernet IP Routing Address Resolution ProtocolProxy ARP Interface Configuration IP Options Processing Network Address TranslationApplications Supported by NAT NAT Configuration Example NAT Mapping Public IP Addresses Private IP Addresses Save exit Network Address Port Translation Napt Configuration ExampleNapt Mapping Public IP Address Private IP Addresses Ip nat inside source list 1 interface se 0.x overload Access-list 1 permit 10.1.3.0Int ethernet 0 ip nat inside int serial 0.x ip nat outside NAT and Napt Configuration Example Ip nat inside source static 10.1.1.1 Dynamic Host Configuration Protocol Server Dhcp Server with NAT Configuration Example Public IP Addresses for NAT Private IP Addresses Dhcp Server at Remote Site Configuration Example Dhcp Relay Agent IP Router Filtering Router SecurityBridge Filtering Provisioning the Router Interface IP FilteringLand Bug Prevention Smurf Attack Prevention Configuring the Router Using Terminal Emulation Security and Logins Limiting Access Controlling Asynchronous Terminal Access Set the configuration option Limiting Dial-In Access via the Modem Port Disabling Isdn Access Controlling Isdn AccessIsdn Call Security Controlling Telnet or FTP Access Limiting Telnet Access Limiting FTP Access Has a Level-1 login and Level-2 telnet access has Controlling Snmp Access Disabling Snmp Access Assigning Snmp Community Names and Access Levels Limiting Snmp Access Through IP Addresses Main Menu → Configuration →General Snmp Management → Snmp Management Enable Management and Communication → Main Menu → Control→ Administer Logins Creating a LoginField Enter Modifying a Login Deleting a Login Access Levels Command Modes Controlling Router CLI AccessLargo Changing Access Levels EnableEnable password password End Security and Logins September Operation and Maintenance Operation and Maintenance Main Menu → Status → Identity Displaying System InformationView this field To find Viewing LEDs and Control Leads Isdn DBM FrameSaverTM SLV FrameSaver SLV 9126 LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads Display LEDs & Control Leads Screen for a FrameSaver SLV FrameSaver SLV 9128-II LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads LED Descriptions General Status LEDs 1Label Indiction Color What It Means ALM General Status LEDs 2 ContdModel 9128-II Network, DSX, or PRI Interface LEDs Label Indication Color What It MeansUser Data Port LED CSU/DSUs Only Ethernet Port LED Routers Only Control Lead Descriptions Additional Control Leads Label Indication What It MeansNetwork Interface User Data Port Device Messages Device Messages 1 What It Indicates What To DoSeen at an FTP Terminal Device Messages 2 What It Indicates What To Do See Changing Software on Device Messages 3 What It Indicates What To Do PVC Device Messages 4 What It Indicates What To Do Reset COM Port usage Device Messages 5 What It Indicates What To DoFrameSaver SLV II only Device Messages 6 What It Indicates What To Do Status Information Status Menu Example Last System Reset Date and Time System and Test Status MessagesMain Menu → Status → System and Test Status Self-Test Results Messages Change Operating Mode Health and Status MessagesHealth and Status Messages 1 What It Indicates Isdn PRI DBM only Frame relay link 1,2 Health and Status Messages 2 What It IndicatesFrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Health and Status Messages 4 What It Indicates Framerelaylink 1,2 Series Access Carrier only Health and Status Messages 5 What It IndicatesPathIP Address Down Nnnn, framerelaylink 1,2 Health and Status Messages 6 What It Indicates Health and Status Messages 7 What It Indicates Configuration→ Time Slot Assignment → FrameRelay Network Assignments and an LMI failure is Test Status Messages Test Status Messages 1 What It IndicatesDclb Active, framerelaylink 1 or Framerelaylink 1 ,3 Test Status Messages 2 What It Indicates Main Menu → Status→ LMI Reported DLCIs Network LMI-Reported DLCIs StatusLMI-Reported DLCIs Status Screen Example Tframe relay network, or Main Menu → Status→ IP Path Connection Status IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates Main Menu → Status→ PVC Connection Status PVC Connection StatusPVC Connection Status Screen Example MgmtPVCName 12. PVC Connection Status 1 Field What It IndicatesEdlci 12. PVC Connection Status 2 Field Status What It Indicates Time Slot Assignment Status Displaying Network Time Slot AssignmentsMain Menu → Status→ Timeslot Assignment Status → Network Network Timeslot Assignment Status Screen Example Cross Connect Status Field bottom Indicates Displaying DSX-1 Time Slot AssignmentsMain Menu → Status→ Timeslot Assignment Status→ DSX-1 DSX-1 Timeslot Assignment Status Screen Example Main Menu → Status→ DBM Interface Status DBM Interface StatusDBM Interface Status Screen Example 13. DBM Interface Status 1 Field What It Indicates Invalid Call ID is displayed Link Name Disabled 13. DBM Interface Status 2 Field What It IndicatesAwarded and Being Delivered In Est Chnl-7 13. DBM Interface Status 3 Field What It Indicates Value is Call AwardedBeing Delivered In Est Chnl-7 Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance IP Routing Table Main Menu → Status→ IP Routing TableIP Routing Table Screen Example 15. IP Routing Table Values 1 Column What It Indicates 15. IP Routing Table Values 2 Column What It Indicates TTL Main Menu → Status→ Performance Statistics Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics Service Level Verification Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Verification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over Service Definitions in , Configuration Options COS ID Size is changed, a new average is not available until a new Main Menu → Status → Performance Statistics→ Dlci Dlci Performance Statistics18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci Frame Relay Performance Statistics Main Menu → Status → Performance Statistics→ Frame RelayFor FrameSaver units with an Isdn DBM 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Errors 20. Frame Relay Performance Statistics 2 What It Indicates 20. Frame Relay Performance Statistics 3 What It Indicates Frame Relay LMI Frame Relay Hdlc Errors 20. Frame Relay Performance Statistics 4 What It Indicates Main Menu → Status → Performance Statistics→ ESF Line ESF Line Performance StatisticsTo select intervals You must enter an interval or time on ESF Line Performance Statistics Screen Example Lofc UAS Lofc DBM Call Performance Statistics 22. DBM Call Performance Statistics What It Indicates Main Menu → Status → Performance Statistics → Ethernet Ethernet Performance Statistics23. Ethernet Performance Statistics What It Indicates Main Menu → Status → Trap Event Log Trap Event LogTrap Event Log Screen Example Activating the Modem PassThru Feature Canceling Modem PassThru OperationMain Menu → Control→ Enable Modem PassThru to COM Main Menu → Control→ Disable Modem PassThru to COM Verifying Modem Operation Manually Disconnecting the ModemMain Menu → Control→ Disconnect Modem Forcing Backup Disruptive Isdn DBM Operation Main Menu→ Test→ Isdn Call/PVC Tests Placing a Test Call NondisruptiveIf the Result is Then Verifying Isdn Lines Verifying That Backup Can Take PlaceSystem Operational should appear FTP File Transfers Command Definition Upgrading System Software If the message displayed is Then Upgrading Isdn BRI DBM Software Main Menu → Status→ Identity Changing Software Determining Whether a Download Is CompletedMain Menu → Control→ Select Software Release Transferring Collected Data If retrieving Hen Turning Off the System Alarm Relay Main Menu → Control→ System Alarm Relay Cut-Off Operation and Maintenance September Troubleshooting Problem Indicators Indicators SeeOperation and Maintenance Main Menu → Status → Display LEDs and Control LEDs Resetting the Unit from the Control Menu Resetting the Unit and Restoring CommunicationResetting the Unit By Cycling the Power Restoring Communication with an Improperly Configured Unit If selecting He following occurs Troubleshooting Management Link Feature LMI Packet Capture Utility Feature LMI Packet Capture Utility→ Display LMI Trace Log LMI Trace Log Example Alarm Conditions 1 What It Indicates What To Do AlarmsMenu → Control → Reset Device Alarm Conditions 2 What It Indicates What To Do Main Menu → Configuration → Isdn → Link ProfilesName IPAddress Alarm Conditions 3 What It Indicates What To Do Menu→ Configuration→LMI Down, frame relay Link Alarm Conditions 4 What It Indicates What To Do DTE Alarm Conditions 5 What It Indicates What To Do PathIP Address Alarm Conditions 6 What It Indicates What To Do Nnnn , frame relay Alarm Conditions 7 What It Indicates What To Do Troubleshooting Tables Device ProblemsDevice Problems 1 Symptom Possible Cause Solutions Viewing the Trap Event Log Device Problems 2 Symptom Possible Cause Solutions Improperly Configured Unit on Frame Relay PVC Problems Frame Relay PVC Problems Symptom Possible Cause Solutions Isdn DBM Problems Symptom Possible Cause Solutions Isdn DBM ProblemsMain Menu → Status → DBM Interface Status Tests Available Test Menu Example Test Timeout Feature DBM Tests When the status of a test is Only command available is Starting and Stopping a Test Aborting All Tests PVC Tests PVC Tests Screen Example PVC Loopback Main Menu → Test→ Network PVC TestMain Menu → Test→ Data Port PVC Tests Main Menu → Test→ Isdn Call/PVC Tests Send Pattern Monitor PatternNetwork PVC Tests/Data Port PVC Tests Isdn Call/PVC Tests Connectivity Test Call Physical Tests Physical Tests Screen Example Main Menu → Test→ Network Physical Tests Line LoopbackLLB Payload Loopback PLB Repeater Loopback RLB AIS DTE Loopback Main Menu → Test→ Data Port Physical TestsDSX Dtlb DTE Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Send Remote Line Loopback Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send and Monitor Pattern Tests Qrss IP Ping Test Ping Screen Example Ping Options 1 Target IP Address Inter-Ping Delay Ping Options 2Source IP Address Packet Size Ping Options 3 Response TimeoutPing Responses Field Possible Values Description IP Ping Test Procedure Main Menu → Test→ IP Ping Lamp Test Main Menu → Test→ Lamp Test His chapter includes Setting Up the OpenLane SLM System OpenLane Support of FrameSaver Devices Setting Up FrameSaver Support Ordering SLM Feature Set Activations To Find Your License Key Number Activation Certificate Administering and Managing SLM Activations Entering an Activation Certificate Checking Activation Certificate Status Scheduling Activations Accessing and Printing the Certificate Summary Report Canceling Scheduled ActivationsChecking the Status of Scheduled Activations 9128-A2-GB20-80 Setting Up NetScout Manager Plus for FrameSaver Devices 10-1 Alarms Preparation10-2 Properties Configuring NetScout Manager Plus 10-3 10-4 Verifying Domains and Groups 10-5 Correcting Domains and Groups 10-6 Property Description Setting 10-7 Adding SLV Alarms Using a Template 10-8 Editing Alarms 10-9 10-10 Adding SLV Alarms Manually 10-11 Field Select or Enter 10-12Paradyne Creating History Files 10-13 10-14 Change 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to Installing the User-Defined History Files Dvuhist -f Dallas51 3 config 30 60 Dallas51k.udhDvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh 10-15 Monitoring a DLCI’s History Data 10-16 10-17 Monitoring the Agent Using NetScout Manager Plus 10-18 10-19 10-20 Statistical Windows SupportedTraffic Statistics Protocol Statistics Setting Up Network Health for FrameSaver Devices 11-1 Installation and Setup of Network Health 11-2 Discovering FrameSaver Elements 11-3 Configuring the Discovered Elements 11-4 Grouping Elements for Reports 11-5 About Service Level Reports Generating Reports for a GroupAbout At-a-Glance Reports 11-6 Reports Applicable to SLV Devices About Trend ReportsPrinted Reports 11-7 11-8 11-9 FrameSaver SLV Plus At-a-Glance Report 11-10 Menu Hierarchy Menus Status Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults MIB Support Downloading MIBs and Snmp Traps System Group mib-2 Interfaces Group mib-2FrameSaver Unit’s sysDescr system FrameSaver Unit’s sysObjectID system Frame Relay Logical Layer NAM Profile Link Name NetScout Indexes to the Interface Table ifTable FR Service T1 FR NAMFR DTE T1 FR NAM Rmon Logical Layer IfName of the interfaceNumber Dlci number ALL Number Dlci number DTE Standards Compliance for Snmp Traps Examples Trap authenticationFailure Trap warmStartTable B-3. warmStart Trap What It Indicates Possible Cause Variable-Binding Traps linkUp and linkDown Physical Sublayer PRIMIB Strings BRI Logical Link Sublayer Traps enterprise-Specific Xxx.xxx.xxx.xxx , COS nn Nnnn ’ ‘Path xxx.xxx.xxx.xxx Up That the secondary clock source Traps RMON-Specific Trap dialControl Standard Dial Control MIB Rmon Alarm and Event Defaults Event DefaultsEventIndex EventDescription EventType EventCommunity Dial Control Extension MIB Physical Interface Alarm Defaults Rising Event Operation Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Dlci Alarm Defaults Paradyne Area MIB FR DTE MIB RFC Dlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.2.2.1 6.1.2.1.2.10.32.2.16.1.2.1.16.12.2.1 MIB Rmon II RFC 6.1.4.1.1795.2.24.2 6.1.4.1.1795.2.24.2.6.9.4Dlci CIR CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.4.26.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.18.9.1 6.1.2.1.10.32.2.1 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 CLI Commands Convention MeaningX.x Xxxxxxxxxxxx Router CLI Commands, Codes, and Designations Pager Command Access Control CommandsTable C-1. Pager Command Table C-2. Access Control Commands Configuration Commands Table C-3. Configuration CommandsConfigure terminal factory Example configure terminal Interface Commands Table C-4. Interface Commands 1Command Mode config, config-if, config-subif Example interface serial 132.53.4.2 Table C-4. Interface Commands 2 Encapsulation encapsulation-type encapsulation-protocolExample ip address 132.53.4.2 Example encapsulation frame-relay ietf Table C-4. Interface Commands 3 No ip unnumbered nullNo frame-relay interface-dlci dlci-num Example ip unnumbered IP Routing Commands Table C-5. IP Routing CommandsNo ip routing No ip multicast-routing Table C-6. Bridge Commands 1 Bridge CommandsExample bridge crb 1 route ip Table C-6. Bridge Commands 2 Command Mode config-if, config-subifNo bridge-group bridge-group Example no bridge-group ARP Commands Table C-7. ARP CommandsArp timeout time No arp timeout time Example arp timeout NAT Commands Table C-8. NAT Commands 1Example ip nat translation timeout No ip nat inside outside Table C-8. NAT Commands 2 Ip nat pool pool-name start-ip-addr end-ip-addrNetmask netmask prefix-length / prefix-length No ip nat pool pool-namestart-ip-addr end-ip-addr Clear ip nat translation Table C-8. NAT Commands 3From previous Dhcp Server Commands Table C-9. Dhcp Server Commands 1No service dhcp No ip dhcp pool pool-name Table C-9. Dhcp Server Commands 2 Default-router ip-address No default-router ip-addressDomain-name domain-name No domain-name domain-name Dns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 3 Network network-num Dhcp Relay Agent Commands Table C-10. Dhcp Relay Agent CommandsNo ip dhcp-server ip-address Example ip dhcp relay max-clients Filter access-list Commands Table C-11. Filter Commands 1Access-list access-list-num permit deny No access-list access-list-numpermit deny Table C-11. Filter Commands 2 For Extended IP Access Lists For Protocol Type Access Lists Table C-11. Filter Commands 3Example access-list 200 permit 0x200 range Table C-11. Filter Commands 4 No ip access-group access-list-1-199numin out Diagnostic Commands Table C-12. Diagnostic Commands 1 Table C-12. Diagnostic Commands 2 Traceroute protocol dest-ipsource source-ip length bytes Show Commands Table C-13. Show Commands 1Show configuration Show arp Table C-13. Show Commands 2 Show configuration saved unsavedShow frame-relay map Show interface intf-type intf-num .sub-intf-num Table C-13. Show Commands 3 Show ip dhcp binding ip-addressShow ip nat translations Show ip route ip-address Show ip traffic Table C-13. Show Commands 4Show spanning-tree Ethernet Type Codes Table C-14. Ethernet Type Codes Hex 1 Description Table C-14. Ethernet Type Codes Hex 2 Description Icmp Designations Protocol and Port DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations Router Command Line Summaries Shortcuts CLI Summaries Table D-1. Show Commands Function Show Command SummaryIntf-type intf-num .sub-intf-num Access Control and System Level Command Summary Table D-2. Access Control and System Level Commands Function CLI Command Summary Table D-3. CLI Commands 1Clear counters intf-type intf-num .sub-intf-num Dns-serverip-address Table D-3. CLI Commands 2 Encapsulation encapsulation-type encapsulation-protocol CLI Command Default Settings Connectors, Cables, and Pin Assignments Rear Panels Connectors, Cables, and Pin Assignments Model COM Port Connector Signal Direction Pin #Pin # Signal Direction COM Port for 9126 and 9128-II 25-Position COM Port-to-PC Cable Feature No -F2-550 COM Port for 9128-II Carrier MountCOM Port Non-Keyed Position Modular Plug DB9 Socket COM Port Non-Keyed COM Port-to-Terminal/Printer Cable Feature No -F2-540Position Modular Plug DB25 Plug COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin # COM Port AUX Port Signal DB25 Pin # DirectionCOM Port-to-Router Cables Cisco 2500 Series Router RJ45 Jack COM Port AUX Port Signal RJ45 Pin # Direction COM Port Console Port Signal DB25 Pin # Direction DB9 Pin #3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # Gender Adapter/Changer LAN Adapter Converter and CablePlug-to-Modular Jack Converter Com Port Position DB25 Plug DTR RTS DTE Port Connector Direction Pin Socket Standard V.35 Straight-through Cable Standard V.35 Crossover CableMM NN Pin DSX-1 Connector DSX-1 Adapter Feature No -F1-560Function Circuit Direction Pin Number Position DB15 Modular Plug Socket Unkeyed DSX-1 Port for 1-Slot 9128-II 15-Position T1 Mass Termination Cable Feature No -F1-500 T1 Network Cable Feature No -F1-500Function Circuit Line # Pin # Canadian T1 Line Interface Cable Feature No -F1-510 Ethernet Port ConnectorPlug Unkeyed Isdn DBM Connector Modem ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Table F-1. NAM Technical Specifications 1 Criteria Physical DimensionsApprovals Physical Environment Table F-1. NAM Technical Specifications 2 Criteria Table F-1. NAM Technical Specifications 3 Criteria Isdn PRI DBM InterfaceB8ZS Ethernet Port Power Consumption Dissipation BRI, NI-1 Isdn BRI DBM InterfaceEthernet Port FrameSaver Typical Power Consumption AC Power RequirementsHeat Dissipation Max Switch Compatibility Service SupportedSwitched Network Interface Standards Compliance Coding Format Framing FormatLine Build-Out LBO Model/Feature EquipmentDescription Number FrameSaver SLV Units Equipment List Isdn PRI DBM FrameSaver SLM Feature Set Upgrade Optional FeaturesPower Supplies NMS Products Series Access Carrier 9128-II NAM only Description Part Number Feature Number Cables Index IN-1 Becn IN-2CLI IN-3 Dhcp IN-4 DBM EER IN-5EIR IN-6 LAN IN-7IP SLV LOF IN-8LOS IN-9 NMS IN-10 OID IN-11 Port IN-12 IN-13 IN-14 IN-15 IN-16