Ethernet Type Codes | Paradyne CSU, DSU, 9126-II, 9128-II instruction

C. Router CLI Commands, Codes, and Designations

Ethernet Type Codes

Use Table C-14, Ethernet Type Codes (Hex), when specifying the filter applied to incoming Ethernet packets by Type Code. Many of the Type Codes listed below are distributed by Xerox Corporation.

Table C-14. Ethernet Type Codes (Hex) (1 of 2)

Type Code		Description		Type Code	Description

0000	–05DC	IEEE802.3 Length Field		803E	DEC Unassigned

010101FF		Experimental		803F	DEC LAN Traffic Monitor

0200		Xerox PUP (see 0A00)		8040–8042	DEC Unassigned

0201		PUP Addr Trans (see 0A01)		8044	Planning Research Corp.

0600		Xerox NS IDP		8046–8047	AT&T

0800		DOD IP		8049	ExperData

0801		X.75 Internet		805B	Stanford V Kernel exp.

0802		NBS Internet		805C	Stanford V Kernel prod.

0803		ECMA Internet		805D	Evans & Sutherland

0804		Chaosnet		8060	Little Machines

0805		X.25 Level 3		8062	Counterpoint Computers

0806		ARP		8065–8066	University of Mass. at Amherst

0807		XNS Compatibility		8067	Veeco Integrated Auto.

081C		Symbolics Private		8068	General Dynamics

0888	–088A	Xyplex		8069	AT&T

0900		Ungermann-Bass net debugger		806A	Autophon

0A00		Xerox IEEE802.3 PUP		806C	ComDesign

0A01		PUP Addr Trans		806D	Computgraphic Corp.

0BAD		Banyan Systems		80E–E8077	Landmark Graphics Corp.

1000		Berkeley Trailer nego		807A	Matra

1001	–100F	Berkeley Trailer encap/IP		807B	Dansk Data Elektronik

1600		Valid Systems		807C	Merit Internodal

4242		PCS Basic Block Protocol		807D–807F	Vitalink Communications

5208		BBN Simnet		8080	Vitalink TransLAN III

6000		DEC Unassigned (Exp.)		8081–8083	Counterpoint Computers

6001		DEC MOP Dump/Load		809B	Appletalk

6002		DEC MOP Remote Console		809C–809E	Datability

6003		DEC DECNET Phase IV Route		809F	Spider Systems Ltd.

9128-A2-GB20-80

September 2002

C-29

Image 411

Paradyne CSU, DSU, 9126-II, 9128-II manual Table C-14. Ethernet Type Codes Hex 1 Description

Contents

FrameSaver SLV Trademarks Warranty, Sales, Service, and Training InformationCopyright 2002 Paradyne Corporation All rights reserved Document Feedback Contents ConfigurationTProcedures Configuration OptionsSeptember Iii Configuring the FrameSaver SLV Router Operation and Maintenance Security and Logins Troubleshooting Lamp Test Vii Setting Up NetScout Manager Plus for FrameSaver DevicesSetting Up Network Health for FrameSaver Devices Menu HierarchyT Snmp MIBs and Traps, and Rmon Alarm Defaults Router CLI TCommands, Codes, and DesignationsViii Connectors, Cables, and Pin Assignments Router Command Line Summaries and Shortcuts Index Technical Specifications Equipment List Purpose and Intended Audience Document OrganizationSection Description Section Description Xii Product-Related Documents XiiiDocument Number Document Title Xiv Conventions Used System Overview About the FrameSaver SLV Router-Specific Features CSU/DSU-Specific Features About the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set FrameSaver SLV Feature Router Maximum Number of PVCs and Management PVCs SupportedThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II Features FrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On Procedure If your login was Hen Select Main Menu Screen Format Description Screen Work Areas Navigating the Screens Keyboard KeysPress For the screen Select Function Press Enter to Function Keys Selecting from a Menu Switching Between Screen Areas Screen Contents Selecting a FieldEntering Information CLI Keyboard Keys Navigating the Router’s CLI Basic Configuration Configuration Procedures Isdn Configuration Menu Configuration Option Area Description Configuration Option Areas Main Menu → Configuration Accessing and Displaying Configuration Options Configuration → PVC Connections Changing Configuration Options Saving Configuration Options Configuration Options Configuration Options Using the Easy Install Feature Main Menu → Easy InstallEasy Install Screen Example Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUs Entering System Information and Setting the System Clock Main Menu → Control→ System InformationIf the selection is Enter Valid characters include For Setting Up the ModemSetting Up Call Directories for Trap Dial-Out Main Menu → Control→ Modem Call Directories Setting Up to Use the Modem PassThru Feature Setting Up Auto-Configuration Main Menu → Auto-ConfigurationAuto-Configuration Screen Example Only applies to models with Selecting a Frame Relay Discovery ModeMain Menu → Auto-Configuration→Frame Relay Discovery Mode Discovery Mode Configuration Description Discovery Mode Configuration Description Automatically Removing a Circuit Setting Up Dial Backup Setting Up the DBM Physical InterfaceMain Menu → Configuration → Isdn → Physical If you select Then Setting Up Automatic Backup Configuration Following prompt When Appears If you select Delete unused Remove AlternateDestinations From PVCs Main Menu → Configuration → Isdn → Link Profiles For Originating a Backup Call For Answering a Backup CallModifying Isdn Link Profiles Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup Timers Assigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp Traps Main Menu → Control→ Change Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Changing Operating Mode Configuration Option Tables System Frame Relay and LMI Options 1 Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs Main Menu → Configuration → System → Frame Relay and LMI System Frame Relay and LMI Options 2 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service Definitions Code Points Assigned Class of Service DefinitionsClass of Svc Name Measure Latency & Availability Name Code Point DefinitionsCode Point Definitions Code Pnt SLV Sample Interval secs Configuring Service Level Verification OptionsService Level Verification Options 1 SLV Type Available Settings Standard, COS 1-COS SLV Timeout Clearing Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Error Event Threshold Service Level Verification Options 3 SLV Latency Clearing Event ThresholdSLV Packet Size bytes General System Options 1 Configuring General System OptionsMain Menu → Configuration → System→ General Test Timeout General System Options 2 General System Options 3 System Alarm Relay Network Physical Interface Options 1 Configuring Physical InterfacesConfiguring the Network Interface Main Menu → Configuration → Network→ Physical Transmit Timing Line Build Out LBO Possible Settings 0.0, -7.5, -15Network Physical Interface Options 2 Bit Stuffing Ansi Performance Report Messages Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Physical Interface Options 3 Network Initiated PLB Circuit Identifier Network Physical Interface Options 4 Data Port Physical Interface Options 1 Configuring a User Data Port CSU/DSUsMain Menu → Configuration → Data Ports→ Physical Port Use Possible Settings Frame Relay, Synchronous Data Transmit Clock Source Data Port Physical Interface Options 2Max Port Rate Kbps Port Base Rate Kbps Data Port Physical Interface Options 3 Monitor RTS ControlMonitor DTR Data Port Physical Interface Options 4 Port DTE Initiated LoopbacksInvert Transmit and Receive Data Data Port Physical Interface Options 5 Action on Network Yellow Alarm Interface Status Configuring the DSX-1 InterfaceMain Menu → Configuration → DSX-1 DSX-1 Physical Interface Options 1 Send All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2 Local Phone Number 1 or Configuring the Isdn DBM InterfaceService Profile ID Spid 1 or Isdn BRI DBM Physical Interface Options Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESS 10. Isdn PRI DBM Physical Interface Options 1Local Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Link Name Setting Up Isdn Link ProfilesMain Menu → Configuration → Isdn → Isdn Link Profiles 11. Isdn Link Profile Options 1 Maximum Link Rate Kbps 11. Isdn Link Profile Options 2Outbound Phone Number Inbound Calling ID 1 or Alternate Outbound Phone Number Assigning Time Slots/Cross Connections11. Isdn Link Profile Options 3 Caller Identification Method Assigning Frame Relay Time Slots to the Network Interface Frame Relay Network Time Slot Assignment Screen ExampleValue Meaning Assigning DSX-1 Time Slots to the Network Interface Time Slot Assignment RuleNtt Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen Example DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen Example Physical Interface Options Clearing Assignments Configuring Frame Relay for an Interface 13. Interface Frame Relay Options 1LMI Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 2Traffic Policing LMI Parameters 13. Interface Frame Relay Options 3 Manually Configuring Dlci Records 14. Dlci Record Options 1Dlci Number 14. Dlci Record Options 2 CIR bpsCommitted Burst Size Bc Bits Outbound Management Priority 14. Dlci Record Options 3Excess Burst Size Bits Dlci Priority 14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, None Source Dlci Configuring PVC ConnectionsMain Menu → Configuration → PVC Connections 15. PVC Connection Options 1 Primary Destination Dlci 15. PVC Connection Options 2Source Edlci Primary Destination Link Alternate Destination Dlci 15. PVC Connection Options 3Primary Destination Edlci Alternate Destination Link Alternate Destination Edlci 15. PVC Connection Options 4 Enter IP Address press ESC to abort ... FWD No Configuring the IP Path ListMain Menu → Configuration → IP Path List Static 16. IP Path List Setting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information 17. Node IP Options 2 TS Access Management Link TS Management Snmp Validation 17. Node IP Options 3 18. Management PVC Options 1 Configuring Management PVCs 18. Management PVC Options 2 Payload ManagedSet DE Primary Dlci 18. Management PVC Options 3 Primary Edlci 18. Management PVC Options 4 18. Management PVC Options 5 Alternate DlciAlternate Edlci Encapsulation 18. Management PVC Options 6 Snmp Management Configuring General Snmp ManagementName 1 Access 19. General Snmp Management Options 1 Configuring Telnet and/or FTP Session Support Name 2 Access19. General Snmp Management Options 2 Telnet Login Required 20. Telnet and FTP Session Options 1Telnet Session 20. Telnet and FTP Session Options 2 Number of Managers Configuring Snmp NMS Security21. Snmp NMS Security Options 1 NMS IP Validation Configuring Snmp Traps and Trap Dial-Out 21. Snmp NMS Security Options 222. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 Link Traps Possible Settings Disable, Up, Down, Both 22. Snmp Traps and Trap Dial-Out Options 3Enterprise Specific Traps Rmon Traps Possible Settings Network, Ports, DBM, All, None22. Snmp Traps and Trap Dial-Out Options 4 Dlci Traps on Interfaces Filter Selection Field Trap Disconnect Dial-Out Delay TIme Min22. Snmp Traps and Trap Dial-Out Options 5 Trap Dial-Out IP SLV Availability Traps 22. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory Latency Traps 23. Ethernet Management Options 1 Configuring Ethernet Management Proxy ARP 23. Ethernet Management Options 2 Configuring the Communication Port 24. Communication Port Options 1Character Length Stop Bits Login Required24. Communication Port Options 2 Parity 24. Communication Port Options 3 RIP 24. Communication Port Options 4 25. Modem Port Options 1 Configuring the Modem Port100 24. Communication Port Options 5 25. Modem Port Options 2 101 25. Modem Port Options 3 102 25. Modem Port Options 4 103 104 Configuring the Criteria for Automatic BackupMain Menu → Configuration → Auto Backup Criteria 26. Auto Backup Criteria Options 1 Backup Allowed Day To nnnn 26. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day From nnnn 106 Configuring the FrameSaver SLV Router FrameSaver SLV Router Overview Network InterfaceEthernet Address Resolution Protocol IP RoutingProxy ARP Interface Configuration Network Address Translation IP Options ProcessingApplications Supported by NAT NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration Example Save exit Napt Configuration Example Network Address Port TranslationNapt Mapping Public IP Address Private IP Addresses Access-list 1 permit 10.1.3.0 Ip nat inside source list 1 interface se 0.x overloadInt ethernet 0 ip nat inside int serial 0.x ip nat outside Ip nat inside source static 10.1.1.1 NAT and Napt Configuration Example Dynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration Example Dhcp Relay Agent Dhcp Server at Remote Site Configuration Example Router Security IP Router FilteringBridge Filtering Smurf Attack Prevention Provisioning the Router InterfaceIP Filtering Land Bug Prevention Configuring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting Access Set the configuration option Limiting Dial-In Access via the Modem Port Controlling Isdn Access Disabling Isdn AccessIsdn Call Security Limiting Telnet Access Controlling Telnet or FTP Access Limiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp Access Assigning Snmp Community Names and Access Levels Management and Communication → Limiting Snmp Access Through IP AddressesMain Menu → Configuration → General Snmp Management → Snmp Management Enable Creating a Login Main Menu → Control→ Administer LoginsField Enter Deleting a Login Modifying a Login Controlling Router CLI Access Access Levels Command ModesLargo End Changing Access LevelsEnable Enable password password Security and Logins September Operation and Maintenance Operation and Maintenance Displaying System Information Main Menu → Status → IdentityView this field To find Isdn DBM Viewing LEDs and Control Leads FrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLV Display LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control Leads ALM LED DescriptionsGeneral Status LEDs 1 Label Indiction Color What It Means 9128-II General Status LEDs 2Contd Model Ethernet Port LED Routers Only Network, DSX, or PRI Interface LEDsLabel Indication Color What It Means User Data Port LED CSU/DSUs Only User Data Port Control Lead DescriptionsAdditional Control Leads Label Indication What It Means Network Interface Terminal Device MessagesDevice Messages 1 What It Indicates What To Do Seen at an FTP See Changing Software on Device Messages 2 What It Indicates What To Do PVC Device Messages 3 What It Indicates What To Do Device Messages 4 What It Indicates What To Do II only Reset COM Port usageDevice Messages 5 What It Indicates What To Do FrameSaver SLV Device Messages 6 What It Indicates What To Do Status Menu Example Status Information Self-Test Results Messages Last System Reset Date and TimeSystem and Test Status Messages Main Menu → Status → System and Test Status Isdn PRI DBM only Change Operating ModeHealth and Status Messages Health and Status Messages 1 What It Indicates Health and Status Messages 2 What It Indicates Frame relay link 1,2FrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It Indicates Nnnn, framerelaylink 1,2 Series Access Carrier onlyHealth and Status Messages 5 What It Indicates PathIP Address Down Health and Status Messages 6 What It Indicates Configuration→ Time Slot Assignment → Frame Health and Status Messages 7 What It IndicatesRelay Network Assignments and an LMI failure is Framerelaylink 1 ,3 Test Status MessagesTest Status Messages 1 What It Indicates Dclb Active, framerelaylink 1 or Test Status Messages 2 What It Indicates Network LMI-Reported DLCIs Status Main Menu → Status→ LMI Reported DLCIsLMI-Reported DLCIs Status Screen Example Tframe relay network, or IP Path Connection Status Main Menu → Status→ IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates PVC Connection Status Main Menu → Status→ PVC Connection StatusPVC Connection Status Screen Example 12. PVC Connection Status 1 Field What It Indicates MgmtPVCNameEdlci Status What It Indicates 12. PVC Connection Status 2 Field Network Timeslot Assignment Status Screen Example Time Slot Assignment StatusDisplaying Network Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status → Network DSX-1 Timeslot Assignment Status Screen Example Cross Connect Status Field bottom IndicatesDisplaying DSX-1 Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status→ DSX-1 DBM Interface Status Main Menu → Status→ DBM Interface StatusDBM Interface Status Screen Example Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It Indicates Delivered In Est Chnl-7 Link Name Disabled13. DBM Interface Status 2 Field What It Indicates Awarded and Being Chnl-7 13. DBM Interface Status 3 Field What It IndicatesValue is Call Awarded Being Delivered In Est Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance 15. IP Routing Table Values 1 Column What It Indicates IP Routing TableMain Menu → Status→ IP Routing Table IP Routing Table Screen Example TTL 15. IP Routing Table Values 2 Column What It Indicates Performance Statistics Main Menu → Status→ Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance Statistics Verification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration Options Size is changed, a new average is not available until a new Dlci Performance Statistics Main Menu → Status → Performance Statistics→ Dlci18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics→ Frame Relay For FrameSaver units with an Isdn DBM 20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay Errors Frame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates 20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc Errors ESF Line Performance Statistics Main Menu → Status → Performance Statistics→ ESF LineTo select intervals You must enter an interval or time on Lofc ESF Line Performance Statistics Screen Example Lofc UAS 22. DBM Call Performance Statistics What It Indicates DBM Call Performance Statistics Ethernet Performance Statistics Main Menu → Status → Performance Statistics → Ethernet23. Ethernet Performance Statistics What It Indicates Trap Event Log Main Menu → Status → Trap Event LogTrap Event Log Screen Example Main Menu → Control→ Disable Modem PassThru to COM Activating the Modem PassThru FeatureCanceling Modem PassThru Operation Main Menu → Control→ Enable Modem PassThru to COM Manually Disconnecting the Modem Verifying Modem OperationMain Menu → Control→ Disconnect Modem Isdn DBM Operation Forcing Backup Disruptive Placing a Test Call Nondisruptive Main Menu→ Test→ Isdn Call/PVC TestsIf the Result is Then Verifying That Backup Can Take Place Verifying Isdn LinesSystem Operational should appear FTP File Transfers Command Definition If the message displayed is Then Upgrading System Software Main Menu → Status→ Identity Upgrading Isdn BRI DBM Software Determining Whether a Download Is Completed Changing SoftwareMain Menu → Control→ Select Software Release If retrieving Hen Transferring Collected Data Main Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm Relay Operation and Maintenance September Troubleshooting Main Menu → Status → Display LEDs and Control LEDs Problem IndicatorsIndicators See Operation and Maintenance Resetting the Unit and Restoring Communication Resetting the Unit from the Control MenuResetting the Unit By Cycling the Power If selecting He following occurs Restoring Communication with an Improperly Configured Unit LMI Packet Capture Utility Feature Troubleshooting Management Link Feature LMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace Log Alarms Alarm Conditions 1 What It Indicates What To DoMenu → Control → Reset Device IPAddress Alarm Conditions 2 What It Indicates What To DoMain Menu → Configuration → Isdn → Link Profiles Name Link Alarm Conditions 3 What It Indicates What To DoMenu→ Configuration→ LMI Down, frame relay DTE Alarm Conditions 4 What It Indicates What To Do PathIP Address Alarm Conditions 5 What It Indicates What To Do Nnnn , frame relay Alarm Conditions 6 What It Indicates What To Do Alarm Conditions 7 What It Indicates What To Do Viewing the Trap Event Log Troubleshooting TablesDevice Problems Device Problems 1 Symptom Possible Cause Solutions Improperly Configured Unit on Device Problems 2 Symptom Possible Cause Solutions Frame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC Problems Isdn DBM Problems Isdn DBM Problems Symptom Possible Cause SolutionsMain Menu → Status → DBM Interface Status Test Menu Example Tests Available DBM Tests Test Timeout Feature Starting and Stopping a Test When the status of a test is Only command available is Aborting All Tests PVC Tests Screen Example PVC Tests Main Menu → Test→ Isdn Call/PVC Tests PVC LoopbackMain Menu → Test→ Network PVC Test Main Menu → Test→ Data Port PVC Tests Isdn Call/PVC Tests Send PatternMonitor Pattern Network PVC Tests/Data Port PVC Tests Test Call Connectivity Physical Tests Screen Example Physical Tests Line Loopback Main Menu → Test→ Network Physical TestsLLB PLB Payload Loopback RLB AIS Repeater Loopback Dtlb DTE DTE LoopbackMain Menu → Test→ Data Port Physical Tests DSX Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line Loopback Qrss Send and Monitor Pattern Tests Ping Screen Example IP Ping Test Target IP Address Ping Options 1 Packet Size Inter-Ping DelayPing Options 2 Source IP Address Response Timeout Ping Options 3Ping Responses Field Possible Values Description Main Menu → Test→ IP Ping IP Ping Test Procedure Main Menu → Test→ Lamp Test Lamp Test His chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM System Setting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set Activations Activation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation Certificate Scheduling Activations Canceling Scheduled Activations Accessing and Printing the Certificate Summary ReportChecking the Status of Scheduled Activations 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver Devices Properties AlarmsPreparation 10-2 10-3 Configuring NetScout Manager Plus 10-4 10-5 Verifying Domains and Groups 10-6 Correcting Domains and Groups 10-7 Property Description Setting 10-8 Adding SLV Alarms Using a Template 10-9 Editing Alarms 10-10 10-11 Adding SLV Alarms Manually 10-12 Field Select or EnterParadyne 10-13 Creating History Files Change 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-14 10-15 Installing the User-Defined History FilesDvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Dvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh 10-16 Monitoring a DLCI’s History Data 10-17 10-18 Monitoring the Agent Using NetScout Manager Plus 10-19 Statistical Windows Supported 10-20Traffic Statistics Protocol Statistics 11-1 Setting Up Network Health for FrameSaver Devices 11-2 Installation and Setup of Network Health 11-3 Discovering FrameSaver Elements 11-4 Configuring the Discovered Elements 11-5 Grouping Elements for Reports 11-6 About Service Level ReportsGenerating Reports for a Group About At-a-Glance Reports 11-7 Reports Applicable to SLV DevicesAbout Trend Reports Printed Reports 11-8 FrameSaver SLV Plus At-a-Glance Report 11-9 11-10 Menus Menu Hierarchy Status Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB Support FrameSaver Unit’s sysObjectID system System Group mib-2Interfaces Group mib-2 FrameSaver Unit’s sysDescr system Frame Relay Logical Layer Profile Link Name NAM FR Service T1 FR NAM NetScout Indexes to the Interface Table ifTableFR DTE T1 FR NAM Number Dlci number DTE Rmon Logical LayerIfName of the interface Number Dlci number ALL Examples Standards Compliance for Snmp Traps Variable-Binding Trap authenticationFailureTrap warmStart Table B-3. warmStart Trap What It Indicates Possible Cause Traps linkUp and linkDown Strings Physical SublayerPRI MIB Logical Link Sublayer BRI Xxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific ‘Path xxx.xxx.xxx.xxx Up Nnnn ’ That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControl Dial Control Extension MIB Rmon Alarm and Event DefaultsEvent Defaults EventIndex EventDescription EventType EventCommunity Rising Event Operation Physical Interface Alarm Defaults Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne Area Dlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order MIB Rmon II RFC 6.1.2.1.2.2.16.1.2.1.2.10.32.2.1 6.1.2.1.16.12.2.1 CIR 6.1.4.1.1795.2.24.26.1.4.1.1795.2.24.2.6.9.4 Dlci CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.4.2 6.1.4.1.1795.2.24.2.6.9.4.5.2.16.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.1 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Xxxxxxxxxxxx CLI CommandsConvention Meaning X.x Router CLI Commands, Codes, and Designations Table C-2. Access Control Commands Pager CommandAccess Control Commands Table C-1. Pager Command Example configure terminal Configuration CommandsTable C-3. Configuration Commands Configure terminal factory Example interface serial 132.53.4.2 Interface CommandsTable C-4. Interface Commands 1 Command Mode config, config-if, config-subif Example encapsulation frame-relay ietf Table C-4. Interface Commands 2Encapsulation encapsulation-type encapsulation-protocol Example ip address 132.53.4.2 Example ip unnumbered Table C-4. Interface Commands 3No ip unnumbered null No frame-relay interface-dlci dlci-num No ip multicast-routing IP Routing CommandsTable C-5. IP Routing Commands No ip routing Bridge Commands Table C-6. Bridge Commands 1Example bridge crb 1 route ip Example no bridge-group Table C-6. Bridge Commands 2Command Mode config-if, config-subif No bridge-group bridge-group Example arp timeout ARP CommandsTable C-7. ARP Commands Arp timeout time No arp timeout time No ip nat inside outside NAT CommandsTable C-8. NAT Commands 1 Example ip nat translation timeout No ip nat pool pool-namestart-ip-addr end-ip-addr Table C-8. NAT Commands 2Ip nat pool pool-name start-ip-addr end-ip-addr Netmask netmask prefix-length / prefix-length Table C-8. NAT Commands 3 Clear ip nat translationFrom previous No ip dhcp pool pool-name Dhcp Server CommandsTable C-9. Dhcp Server Commands 1 No service dhcp Dns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 2Default-router ip-address No default-router ip-address Domain-name domain-name No domain-name domain-name Network network-num Table C-9. Dhcp Server Commands 3 Example ip dhcp relay max-clients Dhcp Relay Agent CommandsTable C-10. Dhcp Relay Agent Commands No ip dhcp-server ip-address No access-list access-list-numpermit deny Filter access-list CommandsTable C-11. Filter Commands 1 Access-list access-list-num permit deny For Extended IP Access Lists Table C-11. Filter Commands 2 Table C-11. Filter Commands 3 For Protocol Type Access ListsExample access-list 200 permit 0x200 range No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4 Table C-12. Diagnostic Commands 1 Diagnostic Commands Traceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2 Show arp Show CommandsTable C-13. Show Commands 1 Show configuration Show interface intf-type intf-num .sub-intf-num Table C-13. Show Commands 2Show configuration saved unsaved Show frame-relay map Show ip route ip-address Table C-13. Show Commands 3Show ip dhcp binding ip-address Show ip nat translations Table C-13. Show Commands 4 Show ip trafficShow spanning-tree Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type Codes Table C-14. Ethernet Type Codes Hex 2 Description Protocol and Port Designations Icmp DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries Shortcuts Show Command Summary Table D-1. Show Commands FunctionIntf-type intf-num .sub-intf-num Table D-2. Access Control and System Level Commands Function Access Control and System Level Command Summary Dns-serverip-address CLI Command SummaryTable D-3. CLI Commands 1 Clear counters intf-type intf-num .sub-intf-num Encapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2 CLI Command Default Settings Rear Panels Connectors, Cables, and Pin Assignments Connectors, Cables, and Pin Assignments Model COM Port for 9126 and 9128-II 25-Position COM Port ConnectorSignal Direction Pin # Pin # Signal Direction Modular Plug DB9 Socket COM Port-to-PC Cable Feature No -F2-550COM Port for 9128-II Carrier Mount COM Port Non-Keyed Position COM Port-to-Terminal/Printer Cable Feature No -F2-540 COM Port Non-KeyedPosition Modular Plug DB25 Plug Cisco 2500 Series Router RJ45 Jack COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port AUX Port Signal DB25 Pin # Direction COM Port-to-Router Cables COM Port Console Port Signal DB25 Pin # Direction DB9 Pin # COM Port AUX Port Signal RJ45 Pin # Direction3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # DTR RTS Gender Adapter/ChangerLAN Adapter Converter and Cable Plug-to-Modular Jack Converter Com Port Position DB25 Plug Direction Pin Socket DTE Port Connector Pin Standard V.35 Straight-through CableStandard V.35 Crossover Cable MM NN Position DB15 Modular Plug Socket Unkeyed DSX-1 ConnectorDSX-1 Adapter Feature No -F1-560 Function Circuit Direction Pin Number DSX-1 Port for 1-Slot 9128-II 15-Position T1 Network Cable Feature No -F1-500 T1 Mass Termination Cable Feature No -F1-500Function Circuit Line # Pin # Ethernet Port Connector Canadian T1 Line Interface Cable Feature No -F1-510Plug Unkeyed Modem Connector Isdn DBM ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Physical Environment Table F-1. NAM Technical Specifications 1 CriteriaPhysical Dimensions Approvals Table F-1. NAM Technical Specifications 2 Criteria Ethernet Port Table F-1. NAM Technical Specifications 3 CriteriaIsdn PRI DBM Interface B8ZS Power Consumption Dissipation Isdn BRI DBM Interface BRI, NI-1Ethernet Port FrameSaver AC Power Requirements Typical Power ConsumptionHeat Dissipation Max Standards Compliance Switch CompatibilityService Supported Switched Network Interface Framing Format Coding FormatLine Build-Out LBO FrameSaver SLV Units Model/FeatureEquipment Description Number Equipment List Isdn PRI DBM NMS Products FrameSaver SLM Feature Set UpgradeOptional Features Power Supplies Series Access Carrier 9128-II NAM only Cables Description Part Number Feature Number IN-1 Index IN-2 BecnCLI Dhcp IN-3 DBM IN-4 IN-5 EEREIR IN-6 IN-7 LANIP SLV IN-8 LOFLOS NMS IN-9 OID IN-10 Port IN-11 IN-12 IN-13 IN-14 IN-15 IN-16