General System Options 3, System Alarm Relay | Paradyne 9126-II

4. Configuration Options

Table 4-5. General System Options (3 of 3)

System Alarm Relay

Possible Settings: Enable, Disable

Default Setting: Disable

Specifies whether an alarm condition for the unit will activate the system alarm relay. The alarm relay is deactivated when the condition causing the alarm is corrected. If more than one alarm condition is present, the alarm relay remains active until all alarm conditions are cleared.

You can also deactivate an alarm via the System Alarm Relay Cut-Off selection from the Control menu; however, the alarm itself is not cleared. When another alarm condition is detected, the alarm is reactivated again, requiring another manual deactivation of the alarm relay.

Display Conditions – This option only appears for a FrameSaver SLV 9128-II installed in the 9000 Series Access Carrier.

Alarm conditions are:

Alarm Indication Signal (AIS) received at the Network, DSX-1, or PRI interface

Continuous Loss of Signal (LOS) condition at the Network, DSX-1, or PRI interface

CTS Down

DBM Download Required

DBM BRI Card Failed

Device Fail

DLCI Down

DTR Down

Ethernet Link Down

Excessive Error Rate (EER) detected at the Network or PRI interface

Internal Modem Failed

ISDN Network Failure

LMI Down

Network Communication Link Down

Out of Frame (OOF) at Network, DSX-1, or PRI

Primary or Secondary Clock Failure

Power Supply/Fan Failure

RTS Down

Self-Test Failure

SLV Latency Exceeded

SLV Timeout

Suboptimal (Maximum) Link Rate Cannot be Achieved

TTwo Level-1 Users Accessing Device

Yellow Alarm Signal on the Network, DSX-1, or PRI interface

Enable – Activates alarm conditions on the system alarm relay when an alarm condition occurs.

Disable – Does not activate the system alarm relay when an alarm condition occurs.

9128-A2-GB20-80

September 2002

4-33

Image 77

Paradyne 9126-II, CSU, DSU, 9128-II manual General System Options 3, System Alarm Relay

Contents

FrameSaver SLV Copyright 2002 Paradyne Corporation All rights reserved Warranty, Sales, Service, and Training InformationDocument Feedback Trademarks Contents September ConfigurationTProceduresConfiguration Options Iii Configuring the FrameSaver SLV Router Operation and Maintenance Security and Logins Troubleshooting Lamp Test Setting Up Network Health for FrameSaver Devices Setting Up NetScout Manager Plus for FrameSaver DevicesMenu HierarchyT Vii Viii Snmp MIBs and Traps, and Rmon Alarm DefaultsRouter CLI TCommands, Codes, and Designations Connectors, Cables, and Pin Assignments Router Command Line Summaries and Shortcuts Index Technical Specifications Equipment List Section Description Purpose and Intended AudienceDocument Organization Section Description Xii Document Number Document Title Product-Related DocumentsXiii Xiv Conventions Used System Overview About the FrameSaver SLV Router-Specific Features CSU/DSU-Specific Features About the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set Through 120 Connections PVCs Dedicated Management FrameSaver SLV Feature RouterMaximum Number of PVCs and Management PVCs Supported About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II Features FrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On Procedure If your login was Hen Select Main Menu Screen Format Description Screen Work Areas Press Navigating the ScreensKeyboard Keys For the screen Select Function Press Enter to Function Keys Selecting from a Menu Switching Between Screen Areas Entering Information Screen ContentsSelecting a Field CLI Keyboard Keys Navigating the Router’s CLI Basic Configuration Configuration Procedures Isdn Configuration Menu Configuration Option Area Description Configuration Option Areas Main Menu → Configuration Accessing and Displaying Configuration Options Configuration → PVC Connections Changing Configuration Options Saving Configuration Options Configuration Options Configuration Options Easy Install Screen Example Using the Easy Install FeatureMain Menu → Easy Install Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUs If the selection is Enter Entering System Information and Setting the System ClockMain Menu → Control→ System Information Setting Up Call Directories for Trap Dial-Out Setting Up the ModemMain Menu → Control→ Modem Call Directories Valid characters include For Setting Up to Use the Modem PassThru Feature Auto-Configuration Screen Example Setting Up Auto-ConfigurationMain Menu → Auto-Configuration Main Menu → Auto-Configuration→Frame Relay Discovery Mode Selecting a Frame Relay Discovery ModeDiscovery Mode Configuration Description Only applies to models with Discovery Mode Configuration Description Automatically Removing a Circuit Main Menu → Configuration → Isdn → Physical Setting Up Dial BackupSetting Up the DBM Physical Interface If you select Then Setting Up Automatic Backup Configuration Following prompt When Appears If you select Destinations Remove AlternateFrom PVCs Delete unused Modifying Isdn Link Profiles Main Menu → Configuration → Isdn → Link ProfilesFor Originating a Backup Call For Answering a Backup Call Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup Timers Assigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp Traps Setting Up Back-to-Back Operation PVC Backup Over the Network InterfaceChanging Operating Mode Main Menu → Control→ Change Operating Mode Configuration Option Tables Configuring Frame Relay and LMI for the System CSU/DSUs Configuring the Overall SystemMain Menu → Configuration → System → Frame Relay and LMI System Frame Relay and LMI Options 1 System Frame Relay and LMI Options 2 System Frame Relay and LMI Options 3 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service Definitions Class of Svc Name Class of Service DefinitionsMeasure Latency & Availability Code Points Assigned Code Point Definitions Code Point DefinitionsCode Pnt Name Service Level Verification Options 1 Configuring Service Level Verification OptionsSLV Type Available Settings Standard, COS 1-COS SLV Sample Interval secs Dlci Down on SLV Timeout Service Level Verification Options 2SLV Timeout Error Event Threshold SLV Timeout Clearing Event Threshold SLV Packet Size bytes Service Level Verification Options 3SLV Latency Clearing Event Threshold Main Menu → Configuration → System→ General Configuring General System OptionsTest Timeout General System Options 1 General System Options 2 General System Options 3 System Alarm Relay Configuring the Network Interface Configuring Physical InterfacesMain Menu → Configuration → Network→ Physical Network Physical Interface Options 1 Network Physical Interface Options 2 Line Build Out LBO Possible Settings 0.0, -7.5, -15Bit Stuffing Transmit Timing Network Physical Interface Options 3 Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Initiated PLB Ansi Performance Report Messages Circuit Identifier Network Physical Interface Options 4 Main Menu → Configuration → Data Ports→ Physical Configuring a User Data Port CSU/DSUsPort Use Possible Settings Frame Relay, Synchronous Data Data Port Physical Interface Options 1 Max Port Rate Kbps Data Port Physical Interface Options 2Port Base Rate Kbps Transmit Clock Source Monitor DTR Data Port Physical Interface Options 3Monitor RTS Control Invert Transmit and Receive Data Data Port Physical Interface Options 4Port DTE Initiated Loopbacks Data Port Physical Interface Options 5 Action on Network Yellow Alarm Main Menu → Configuration → DSX-1 Configuring the DSX-1 InterfaceDSX-1 Physical Interface Options 1 Interface Status Send All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2 Service Profile ID Spid 1 or Configuring the Isdn DBM InterfaceIsdn BRI DBM Physical Interface Options Local Phone Number 1 or Local Phone Number Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESS10. Isdn PRI DBM Physical Interface Options 1 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Main Menu → Configuration → Isdn → Isdn Link Profiles Setting Up Isdn Link Profiles11. Isdn Link Profile Options 1 Link Name Outbound Phone Number 11. Isdn Link Profile Options 2Inbound Calling ID 1 or Maximum Link Rate Kbps 11. Isdn Link Profile Options 3 Assigning Time Slots/Cross ConnectionsCaller Identification Method Alternate Outbound Phone Number Value Meaning Assigning Frame Relay Time Slots to the Network InterfaceFrame Relay Network Time Slot Assignment Screen Example Ntt Assigning DSX-1 Time Slots to the Network InterfaceTime Slot Assignment Rule Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen Example DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen Example Physical Interface Options Clearing Assignments LMI Configuring Frame Relay for an Interface13. Interface Frame Relay Options 1 Traffic Policing 13. Interface Frame Relay Options 2LMI Parameters Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 3 Dlci Number Manually Configuring Dlci Records14. Dlci Record Options 1 Committed Burst Size Bc Bits 14. Dlci Record Options 2CIR bps Excess Burst Size Bits 14. Dlci Record Options 3Dlci Priority Outbound Management Priority 14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, None Main Menu → Configuration → PVC Connections Configuring PVC Connections15. PVC Connection Options 1 Source Dlci Source Edlci 15. PVC Connection Options 2Primary Destination Link Primary Destination Dlci Primary Destination Edlci 15. PVC Connection Options 3Alternate Destination Link Alternate Destination Dlci Alternate Destination Edlci 15. PVC Connection Options 4 Main Menu → Configuration → IP Path List Static Configuring the IP Path List16. IP Path List Enter IP Address press ESC to abort ... FWD No Setting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information 17. Node IP Options 2 TS Access Management Link TS Management Snmp Validation 17. Node IP Options 3 18. Management PVC Options 1 Configuring Management PVCs Set DE 18. Management PVC Options 2Payload Managed Primary Dlci 18. Management PVC Options 3 Primary Edlci 18. Management PVC Options 4 Alternate Edlci 18. Management PVC Options 5Alternate Dlci Encapsulation 18. Management PVC Options 6 Name 1 Access Configuring General Snmp Management19. General Snmp Management Options 1 Snmp Management 19. General Snmp Management Options 2 Configuring Telnet and/or FTP Session SupportName 2 Access Telnet Session Telnet Login Required20. Telnet and FTP Session Options 1 20. Telnet and FTP Session Options 2 21. Snmp NMS Security Options 1 Configuring Snmp NMS SecurityNMS IP Validation Number of Managers 22. Snmp Traps and Trap Dial-Out Options 1 Configuring Snmp Traps and Trap Dial-Out21. Snmp NMS Security Options 2 22. Snmp Traps and Trap Dial-Out Options 2 Enterprise Specific Traps Link Traps Possible Settings Disable, Up, Down, Both22. Snmp Traps and Trap Dial-Out Options 3 22. Snmp Traps and Trap Dial-Out Options 4 Possible Settings Network, Ports, DBM, All, NoneDlci Traps on Interfaces Filter Selection Field Rmon Traps 22. Snmp Traps and Trap Dial-Out Options 5 Dial-Out Delay TIme MinTrap Dial-Out Trap Disconnect Alternate Dial-Out Directory 22. Snmp Traps and Trap Dial-Out Options 6Latency Traps IP SLV Availability Traps 23. Ethernet Management Options 1 Configuring Ethernet Management Proxy ARP 23. Ethernet Management Options 2 Character Length Configuring the Communication Port24. Communication Port Options 1 24. Communication Port Options 2 Login RequiredParity Stop Bits 24. Communication Port Options 3 RIP 24. Communication Port Options 4 100 Configuring the Modem Port24. Communication Port Options 5 25. Modem Port Options 1 25. Modem Port Options 2 101 25. Modem Port Options 3 102 25. Modem Port Options 4 103 Main Menu → Configuration → Auto Backup Criteria Configuring the Criteria for Automatic Backup26. Auto Backup Criteria Options 1 104 When Auto Backup Allowed 26. Auto Backup Criteria Options 2Backup Allowed Day From nnnn Backup Allowed Day To nnnn 106 Configuring the FrameSaver SLV Router Ethernet FrameSaver SLV Router OverviewNetwork Interface Proxy ARP Address Resolution ProtocolIP Routing Interface Configuration Applications Supported by NAT Network Address TranslationIP Options Processing NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration Example Save exit Napt Mapping Public IP Address Private IP Addresses Napt Configuration ExampleNetwork Address Port Translation Int ethernet 0 ip nat inside int serial 0.x ip nat outside Access-list 1 permit 10.1.3.0Ip nat inside source list 1 interface se 0.x overload Ip nat inside source static 10.1.1.1 NAT and Napt Configuration Example Dynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration Example Dhcp Relay Agent Dhcp Server at Remote Site Configuration Example Bridge Filtering Router SecurityIP Router Filtering IP Filtering Provisioning the Router InterfaceLand Bug Prevention Smurf Attack Prevention Configuring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting Access Set the configuration option Limiting Dial-In Access via the Modem Port Isdn Call Security Controlling Isdn AccessDisabling Isdn Access Limiting Telnet Access Controlling Telnet or FTP Access Limiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp Access Assigning Snmp Community Names and Access Levels Main Menu → Configuration → Limiting Snmp Access Through IP AddressesGeneral Snmp Management → Snmp Management Enable Management and Communication → Field Enter Creating a LoginMain Menu → Control→ Administer Logins Deleting a Login Modifying a Login Largo Controlling Router CLI AccessAccess Levels Command Modes Enable Changing Access LevelsEnable password password End Security and Logins September Operation and Maintenance Operation and Maintenance View this field To find Displaying System InformationMain Menu → Status → Identity Isdn DBM Viewing LEDs and Control Leads FrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLV Display LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control Leads General Status LEDs 1 LED DescriptionsLabel Indiction Color What It Means ALM Contd General Status LEDs 2Model 9128-II Label Indication Color What It Means Network, DSX, or PRI Interface LEDsUser Data Port LED CSU/DSUs Only Ethernet Port LED Routers Only Additional Control Leads Label Indication What It Means Control Lead DescriptionsNetwork Interface User Data Port Device Messages 1 What It Indicates What To Do Device MessagesSeen at an FTP Terminal See Changing Software on Device Messages 2 What It Indicates What To Do PVC Device Messages 3 What It Indicates What To Do Device Messages 4 What It Indicates What To Do Device Messages 5 What It Indicates What To Do Reset COM Port usageFrameSaver SLV II only Device Messages 6 What It Indicates What To Do Status Menu Example Status Information System and Test Status Messages Last System Reset Date and TimeMain Menu → Status → System and Test Status Self-Test Results Messages Health and Status Messages Change Operating ModeHealth and Status Messages 1 What It Indicates Isdn PRI DBM only FrameSaver SLV 9126-II or Health and Status Messages 2 What It IndicatesFrame relay link 1,2 Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It Indicates Health and Status Messages 5 What It Indicates Series Access Carrier onlyPathIP Address Down Nnnn, framerelaylink 1,2 Health and Status Messages 6 What It Indicates Relay Network Assignments and an LMI failure is Configuration→ Time Slot Assignment → FrameHealth and Status Messages 7 What It Indicates Test Status Messages 1 What It Indicates Test Status MessagesDclb Active, framerelaylink 1 or Framerelaylink 1 ,3 Test Status Messages 2 What It Indicates LMI-Reported DLCIs Status Screen Example Network LMI-Reported DLCIs StatusMain Menu → Status→ LMI Reported DLCIs Tframe relay network, or IP Path Connection Status Screen Example IP Path Connection StatusMain Menu → Status→ IP Path Connection Status 11. IP Path Connection Status Field What It Indicates PVC Connection Status Screen Example PVC Connection StatusMain Menu → Status→ PVC Connection Status Edlci 12. PVC Connection Status 1 Field What It IndicatesMgmtPVCName Status What It Indicates 12. PVC Connection Status 2 Field Displaying Network Time Slot Assignments Time Slot Assignment StatusMain Menu → Status→ Timeslot Assignment Status → Network Network Timeslot Assignment Status Screen Example Displaying DSX-1 Time Slot Assignments Cross Connect Status Field bottom IndicatesMain Menu → Status→ Timeslot Assignment Status→ DSX-1 DSX-1 Timeslot Assignment Status Screen Example DBM Interface Status Screen Example DBM Interface StatusMain Menu → Status→ DBM Interface Status Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It Indicates 13. DBM Interface Status 2 Field What It Indicates Link Name DisabledAwarded and Being Delivered In Est Chnl-7 Value is Call Awarded 13. DBM Interface Status 3 Field What It IndicatesBeing Delivered In Est Chnl-7 Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance Main Menu → Status→ IP Routing Table IP Routing TableIP Routing Table Screen Example 15. IP Routing Table Values 1 Column What It Indicates TTL 15. IP Routing Table Values 2 Column What It Indicates Performance Statistics Menu Performance StatisticsMain Menu → Status→ Performance Statistics Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance Statistics Verification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration Options Size is changed, a new average is not available until a new 18. Dlci Performance Statistics 1 What It Indicates Dlci Performance StatisticsMain Menu → Status → Performance Statistics→ Dlci 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci Main Menu → Status → Performance Statistics→ Frame Relay Frame Relay Performance StatisticsFor FrameSaver units with an Isdn DBM 20. Frame Relay Performance Statistics 1 What It Indicates 20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay Errors Frame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates 20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc Errors To select intervals You must enter an interval or time on ESF Line Performance StatisticsMain Menu → Status → Performance Statistics→ ESF Line Lofc ESF Line Performance Statistics Screen Example Lofc UAS 22. DBM Call Performance Statistics What It Indicates DBM Call Performance Statistics 23. Ethernet Performance Statistics What It Indicates Ethernet Performance StatisticsMain Menu → Status → Performance Statistics → Ethernet Trap Event Log Screen Example Trap Event LogMain Menu → Status → Trap Event Log Canceling Modem PassThru Operation Activating the Modem PassThru FeatureMain Menu → Control→ Enable Modem PassThru to COM Main Menu → Control→ Disable Modem PassThru to COM Main Menu → Control→ Disconnect Modem Manually Disconnecting the ModemVerifying Modem Operation Isdn DBM Operation Forcing Backup Disruptive If the Result is Then Placing a Test Call NondisruptiveMain Menu→ Test→ Isdn Call/PVC Tests System Operational should appear Verifying That Backup Can Take PlaceVerifying Isdn Lines FTP File Transfers Command Definition If the message displayed is Then Upgrading System Software Main Menu → Status→ Identity Upgrading Isdn BRI DBM Software Main Menu → Control→ Select Software Release Determining Whether a Download Is CompletedChanging Software If retrieving Hen Transferring Collected Data Main Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm Relay Operation and Maintenance September Troubleshooting Indicators See Problem IndicatorsOperation and Maintenance Main Menu → Status → Display LEDs and Control LEDs Resetting the Unit By Cycling the Power Resetting the Unit and Restoring CommunicationResetting the Unit from the Control Menu If selecting He following occurs Restoring Communication with an Improperly Configured Unit LMI Packet Capture Utility Feature Troubleshooting Management Link Feature LMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace Log Menu → Control → Reset Device AlarmsAlarm Conditions 1 What It Indicates What To Do Main Menu → Configuration → Isdn → Link Profiles Alarm Conditions 2 What It Indicates What To DoName IPAddress Menu→ Configuration→ Alarm Conditions 3 What It Indicates What To DoLMI Down, frame relay Link DTE Alarm Conditions 4 What It Indicates What To Do PathIP Address Alarm Conditions 5 What It Indicates What To Do Nnnn , frame relay Alarm Conditions 6 What It Indicates What To Do Alarm Conditions 7 What It Indicates What To Do Device Problems Troubleshooting TablesDevice Problems 1 Symptom Possible Cause Solutions Viewing the Trap Event Log Improperly Configured Unit on Device Problems 2 Symptom Possible Cause Solutions Frame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC Problems Main Menu → Status → DBM Interface Status Isdn DBM ProblemsIsdn DBM Problems Symptom Possible Cause Solutions Test Menu Example Tests Available DBM Tests Test Timeout Feature Starting and Stopping a Test When the status of a test is Only command available is Aborting All Tests PVC Tests Screen Example PVC Tests Main Menu → Test→ Network PVC Test PVC LoopbackMain Menu → Test→ Data Port PVC Tests Main Menu → Test→ Isdn Call/PVC Tests Monitor Pattern Send PatternNetwork PVC Tests/Data Port PVC Tests Isdn Call/PVC Tests Test Call Connectivity Physical Tests Screen Example Physical Tests LLB Line LoopbackMain Menu → Test→ Network Physical Tests PLB Payload Loopback RLB AIS Repeater Loopback Main Menu → Test→ Data Port Physical Tests DTE LoopbackDSX Dtlb DTE Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line Loopback Qrss Send and Monitor Pattern Tests Ping Screen Example IP Ping Test Target IP Address Ping Options 1 Ping Options 2 Inter-Ping DelaySource IP Address Packet Size Ping Responses Field Possible Values Description Response TimeoutPing Options 3 Main Menu → Test→ IP Ping IP Ping Test Procedure Main Menu → Test→ Lamp Test Lamp Test His chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM System Setting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set Activations Activation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation Certificate Scheduling Activations Checking the Status of Scheduled Activations Canceling Scheduled ActivationsAccessing and Printing the Certificate Summary Report 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver Devices Preparation Alarms10-2 Properties 10-3 Configuring NetScout Manager Plus 10-4 10-5 Verifying Domains and Groups 10-6 Correcting Domains and Groups 10-7 Property Description Setting 10-8 Adding SLV Alarms Using a Template 10-9 Editing Alarms 10-10 10-11 Adding SLV Alarms Manually Paradyne 10-12Field Select or Enter 10-13 Creating History Files Change 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-14 Dvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Installing the User-Defined History FilesDvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh 10-15 10-16 Monitoring a DLCI’s History Data 10-17 10-18 Monitoring the Agent Using NetScout Manager Plus 10-19 Traffic Statistics Protocol Statistics Statistical Windows Supported10-20 11-1 Setting Up Network Health for FrameSaver Devices 11-2 Installation and Setup of Network Health 11-3 Discovering FrameSaver Elements 11-4 Configuring the Discovered Elements 11-5 Grouping Elements for Reports Generating Reports for a Group About Service Level ReportsAbout At-a-Glance Reports 11-6 About Trend Reports Reports Applicable to SLV DevicesPrinted Reports 11-7 11-8 FrameSaver SLV Plus At-a-Glance Report 11-9 11-10 Menus Menu Hierarchy Status Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB Support Interfaces Group mib-2 System Group mib-2FrameSaver Unit’s sysDescr system FrameSaver Unit’s sysObjectID system Frame Relay Logical Layer Profile Link Name NAM FR DTE T1 FR NAM FR Service T1 FR NAMNetScout Indexes to the Interface Table ifTable IfName of the interface Rmon Logical LayerNumber Dlci number ALL Number Dlci number DTE Examples Standards Compliance for Snmp Traps Trap warmStart Trap authenticationFailureTable B-3. warmStart Trap What It Indicates Possible Cause Variable-Binding Traps linkUp and linkDown PRI Physical SublayerMIB Strings Logical Link Sublayer BRI Xxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific ‘Path xxx.xxx.xxx.xxx Up Nnnn ’ That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControl Event Defaults Rmon Alarm and Event DefaultsEventIndex EventDescription EventType EventCommunity Dial Control Extension MIB Rising Event Operation Physical Interface Alarm Defaults Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne Area Dlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.2.10.32.2.1 6.1.2.1.2.2.16.1.2.1.16.12.2.1 MIB Rmon II RFC 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2Dlci CIR CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.4.26.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.1 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Convention Meaning CLI CommandsX.x Xxxxxxxxxxxx Router CLI Commands, Codes, and Designations Access Control Commands Pager CommandTable C-1. Pager Command Table C-2. Access Control Commands Table C-3. Configuration Commands Configuration CommandsConfigure terminal factory Example configure terminal Table C-4. Interface Commands 1 Interface CommandsCommand Mode config, config-if, config-subif Example interface serial 132.53.4.2 Encapsulation encapsulation-type encapsulation-protocol Table C-4. Interface Commands 2Example ip address 132.53.4.2 Example encapsulation frame-relay ietf No ip unnumbered null Table C-4. Interface Commands 3No frame-relay interface-dlci dlci-num Example ip unnumbered Table C-5. IP Routing Commands IP Routing CommandsNo ip routing No ip multicast-routing Example bridge crb 1 route ip Bridge CommandsTable C-6. Bridge Commands 1 Command Mode config-if, config-subif Table C-6. Bridge Commands 2No bridge-group bridge-group Example no bridge-group Table C-7. ARP Commands ARP CommandsArp timeout time No arp timeout time Example arp timeout Table C-8. NAT Commands 1 NAT CommandsExample ip nat translation timeout No ip nat inside outside Ip nat pool pool-name start-ip-addr end-ip-addr Table C-8. NAT Commands 2Netmask netmask prefix-length / prefix-length No ip nat pool pool-namestart-ip-addr end-ip-addr From previous Table C-8. NAT Commands 3Clear ip nat translation Table C-9. Dhcp Server Commands 1 Dhcp Server CommandsNo service dhcp No ip dhcp pool pool-name Default-router ip-address No default-router ip-address Table C-9. Dhcp Server Commands 2Domain-name domain-name No domain-name domain-name Dns-server ip-address No dns-server ip-address Network network-num Table C-9. Dhcp Server Commands 3 Table C-10. Dhcp Relay Agent Commands Dhcp Relay Agent CommandsNo ip dhcp-server ip-address Example ip dhcp relay max-clients Table C-11. Filter Commands 1 Filter access-list CommandsAccess-list access-list-num permit deny No access-list access-list-numpermit deny For Extended IP Access Lists Table C-11. Filter Commands 2 Example access-list 200 permit 0x200 range Table C-11. Filter Commands 3For Protocol Type Access Lists No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4 Table C-12. Diagnostic Commands 1 Diagnostic Commands Traceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2 Table C-13. Show Commands 1 Show CommandsShow configuration Show arp Show configuration saved unsaved Table C-13. Show Commands 2Show frame-relay map Show interface intf-type intf-num .sub-intf-num Show ip dhcp binding ip-address Table C-13. Show Commands 3Show ip nat translations Show ip route ip-address Show spanning-tree Table C-13. Show Commands 4Show ip traffic Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type Codes Table C-14. Ethernet Type Codes Hex 2 Description All 3 n = Destination unreachable Protocol and Port DesignationsIcmp Designations All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries Shortcuts Intf-type intf-num .sub-intf-num Show Command SummaryTable D-1. Show Commands Function Table D-2. Access Control and System Level Commands Function Access Control and System Level Command Summary Table D-3. CLI Commands 1 CLI Command SummaryClear counters intf-type intf-num .sub-intf-num Dns-serverip-address Encapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2 CLI Command Default Settings Rear Panels Connectors, Cables, and Pin Assignments Connectors, Cables, and Pin Assignments Model Signal Direction Pin # COM Port ConnectorPin # Signal Direction COM Port for 9126 and 9128-II 25-Position COM Port for 9128-II Carrier Mount COM Port-to-PC Cable Feature No -F2-550COM Port Non-Keyed Position Modular Plug DB9 Socket Position Modular Plug DB25 Plug COM Port-to-Terminal/Printer Cable Feature No -F2-540COM Port Non-Keyed COM Port AUX Port Signal DB25 Pin # Direction COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port-to-Router Cables Cisco 2500 Series Router RJ45 Jack 3COM Router DB9 Socket COM Port Console Port Signal DB25 Pin # Direction DB9 Pin #COM Port AUX Port Signal RJ45 Pin # Direction COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # LAN Adapter Converter and Cable Gender Adapter/ChangerPlug-to-Modular Jack Converter Com Port Position DB25 Plug DTR RTS Direction Pin Socket DTE Port Connector Standard V.35 Crossover Cable Standard V.35 Straight-through CableMM NN Pin DSX-1 Adapter Feature No -F1-560 DSX-1 ConnectorFunction Circuit Direction Pin Number Position DB15 Modular Plug Socket Unkeyed DSX-1 Port for 1-Slot 9128-II 15-Position Function Circuit Line # Pin # T1 Network Cable Feature No -F1-500T1 Mass Termination Cable Feature No -F1-500 Plug Unkeyed Ethernet Port ConnectorCanadian T1 Line Interface Cable Feature No -F1-510 Isdn Modular Cable Modem ConnectorIsdn DBM Connector Connectors, Cables, and Pin Assignments September Physical Dimensions Table F-1. NAM Technical Specifications 1 CriteriaApprovals Physical Environment Table F-1. NAM Technical Specifications 2 Criteria Isdn PRI DBM Interface Table F-1. NAM Technical Specifications 3 CriteriaB8ZS Ethernet Port Power Consumption Dissipation Ethernet Port FrameSaver Isdn BRI DBM InterfaceBRI, NI-1 Heat Dissipation Max AC Power RequirementsTypical Power Consumption Service Supported Switch CompatibilitySwitched Network Interface Standards Compliance Line Build-Out LBO Framing FormatCoding Format Equipment Model/FeatureDescription Number FrameSaver SLV Units Equipment List Isdn PRI DBM Optional Features FrameSaver SLM Feature Set UpgradePower Supplies NMS Products Series Access Carrier 9128-II NAM only Cables Description Part Number Feature Number IN-1 Index CLI IN-2Becn Dhcp IN-3 DBM IN-4 EIR IN-5EER IN-6 IP SLV IN-7LAN LOS IN-8LOF NMS IN-9 OID IN-10 Port IN-11 IN-12 IN-13 IN-14 IN-15 IN-16