Send Pattern, Monitor Pattern | Paradyne CSU, DSU, 9126-II, 9128-II

8. Troubleshooting

Send Pattern

This test sends packets filled with a hexadecimal 55 test pattern and sequence number over the selected interface and DLCI to another FrameSaver device.

To send a pattern test on a link:

Main Menu → Test→	[Network PVC Tests/Data Port PVC Tests/
ISDN Call/PVC Tests]

If the selected DLCI is			And the default
configured as . . .		Then . . .	Rate (Kbps) setting is . . .

Standard		(Disruptive) appears	100% of CIR
		after Test

Multiplexed		(Non-Disruptive)	10% of CIR
		appears after Test

If the CIR is zero, the pattern will be sent at a rate of 1000 bps.

Monitor Pattern

This test monitors packets filled with a hexadecimal 55 test pattern and sequence number over the selected interface and DLCI to another FrameSaver device.

To monitor a pattern test on a link:

Main Menu → Test→ [Network PVC Tests/Data Port PVC Tests/

ISDN Call/PVC Tests]

The current number of sequence and data errors are shown under the Result column when the FrameSaver unit is in sync. An Out of Sync message appears when 5 frames out of 25 are missing or out of sequence.

These error counts are updated every second. If the maximum count is reached, 99999+ appears in these fields.

8-24

September 2002

9128-A2-GB20-80

Image 288

Paradyne CSU, DSU, 9126-II manual Send Pattern, Monitor Pattern, Network PVC Tests/Data Port PVC Tests, Isdn Call/PVC Tests

Contents

FrameSaver SLV Warranty, Sales, Service, and Training Information Copyright 2002 Paradyne Corporation All rights reservedDocument Feedback Trademarks Contents ConfigurationTProcedures Configuration OptionsSeptember Configuring the FrameSaver SLV Router Iii Security and Logins Operation and Maintenance Troubleshooting Lamp Test Setting Up NetScout Manager Plus for FrameSaver Devices Setting Up Network Health for FrameSaver DevicesMenu HierarchyT Vii Snmp MIBs and Traps, and Rmon Alarm Defaults Router CLI TCommands, Codes, and DesignationsViii Router Command Line Summaries and Shortcuts Connectors, Cables, and Pin Assignments Technical Specifications Equipment List Index Purpose and Intended Audience Document OrganizationSection Description Xii Section Description Product-Related Documents XiiiDocument Number Document Title Conventions Used Xiv About the FrameSaver SLV System Overview CSU/DSU-Specific Features Router-Specific Features About the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set FrameSaver SLV Feature Router Maximum Number of PVCs and Management PVCs SupportedThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaverTSLV 9126-II and 9128-II Features Additional FrameSaver SLV 9128-II Features FrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Procedure Logging On If your login was Hen Main Menu Select Screen Work Areas Screen Format Description Navigating the Screens Keyboard KeysPress Function Keys For the screen Select Function Press Enter to Switching Between Screen Areas Selecting from a Menu Screen Contents Selecting a FieldEntering Information Navigating the Router’s CLI CLI Keyboard Keys Configuration Procedures Basic Configuration Configuration Menu Isdn Configuration Option Areas Configuration Option Area Description Accessing and Displaying Configuration Options Main Menu → Configuration Changing Configuration Options Configuration → PVC Connections Saving Configuration Options Configuration Options Configuration Options Using the Easy Install Feature Main Menu → Easy InstallEasy Install Screen Example Using RIP with FrameSaver SLV CSU/DSUs Configuration → Data Ports→ Dlci Records Entering System Information and Setting the System Clock Main Menu → Control→ System InformationIf the selection is Enter Setting Up the Modem Setting Up Call Directories for Trap Dial-OutMain Menu → Control→ Modem Call Directories Valid characters include For Setting Up to Use the Modem PassThru Feature Setting Up Auto-Configuration Main Menu → Auto-ConfigurationAuto-Configuration Screen Example Selecting a Frame Relay Discovery Mode Main Menu → Auto-Configuration→Frame Relay Discovery ModeDiscovery Mode Configuration Description Only applies to models with Discovery Mode Configuration Description Automatically Removing a Circuit Setting Up Dial Backup Setting Up the DBM Physical InterfaceMain Menu → Configuration → Isdn → Physical Setting Up Automatic Backup Configuration If you select Then Following prompt When Appears If you select Remove Alternate DestinationsFrom PVCs Delete unused Main Menu → Configuration → Isdn → Link Profiles For Originating a Backup Call For Answering a Backup CallModifying Isdn Link Profiles Restricting Automatic Backup and Configuring Backup Timers Main Menu → Configuration → Auto-Backup Criteria Configuring the DBM Interface to Send Snmp Traps Assigning DLCIs to a Backup Group PVC Backup Over the Network Interface Setting Up Back-to-Back OperationChanging Operating Mode Main Menu → Control→ Change Operating Mode Configuration Option Tables Configuring the Overall System Configuring Frame Relay and LMI for the System CSU/DSUsMain Menu → Configuration → System → Frame Relay and LMI System Frame Relay and LMI Options 1 System Frame Relay and LMI Options 2 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Configuring Class of Service Definitions Field Setting After RfcCodePoints Selected Class of Service Definitions Class of Svc NameMeasure Latency & Availability Code Points Assigned Code Point Definitions Code Point DefinitionsCode Pnt Name Configuring Service Level Verification Options Service Level Verification Options 1SLV Type Available Settings Standard, COS 1-COS SLV Sample Interval secs Service Level Verification Options 2 Dlci Down on SLV TimeoutSLV Timeout Error Event Threshold SLV Timeout Clearing Event Threshold Service Level Verification Options 3 SLV Latency Clearing Event ThresholdSLV Packet Size bytes Configuring General System Options Main Menu → Configuration → System→ GeneralTest Timeout General System Options 1 General System Options 2 System Alarm Relay General System Options 3 Configuring Physical Interfaces Configuring the Network InterfaceMain Menu → Configuration → Network→ Physical Network Physical Interface Options 1 Line Build Out LBO Possible Settings 0.0, -7.5, -15 Network Physical Interface Options 2Bit Stuffing Transmit Timing Network Initiated Dclb Possible Settings Disable, V.54&ANSI Network Physical Interface Options 3Network Initiated PLB Ansi Performance Report Messages Network Physical Interface Options 4 Circuit Identifier Configuring a User Data Port CSU/DSUs Main Menu → Configuration → Data Ports→ PhysicalPort Use Possible Settings Frame Relay, Synchronous Data Data Port Physical Interface Options 1 Data Port Physical Interface Options 2 Max Port Rate KbpsPort Base Rate Kbps Transmit Clock Source Data Port Physical Interface Options 3 Monitor RTS ControlMonitor DTR Data Port Physical Interface Options 4 Port DTE Initiated LoopbacksInvert Transmit and Receive Data Action on Network Yellow Alarm Data Port Physical Interface Options 5 Configuring the DSX-1 Interface Main Menu → Configuration → DSX-1DSX-1 Physical Interface Options 1 Interface Status DSX-1 Physical Interface Options 2 Send All Ones on DSX-1 Failure Configuring the Isdn DBM Interface Service Profile ID Spid 1 orIsdn BRI DBM Physical Interface Options Local Phone Number 1 or Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESS 10. Isdn PRI DBM Physical Interface Options 1Local Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Setting Up Isdn Link Profiles Main Menu → Configuration → Isdn → Isdn Link Profiles11. Isdn Link Profile Options 1 Link Name 11. Isdn Link Profile Options 2 Outbound Phone NumberInbound Calling ID 1 or Maximum Link Rate Kbps Assigning Time Slots/Cross Connections 11. Isdn Link Profile Options 3Caller Identification Method Alternate Outbound Phone Number Assigning Frame Relay Time Slots to the Network Interface Frame Relay Network Time Slot Assignment Screen ExampleValue Meaning Assigning DSX-1 Time Slots to the Network Interface Time Slot Assignment RuleNtt DSX-1 to Network Time Slot Assignment Screen Example Ime Slot Assignment Rules DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Synchronous Data Port Assignment Screen Example Sync Data Port Assignment Clearing Assignments Physical Interface Options Configuring Frame Relay for an Interface 13. Interface Frame Relay Options 1LMI 13. Interface Frame Relay Options 2 Traffic PolicingLMI Parameters Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 3 Manually Configuring Dlci Records 14. Dlci Record Options 1Dlci Number 14. Dlci Record Options 2 CIR bpsCommitted Burst Size Bc Bits 14. Dlci Record Options 3 Excess Burst Size BitsDlci Priority Outbound Management Priority Backup Group Possible Settings A, B, C, . . . Z, None 14. Dlci Record Options 4 Configuring PVC Connections Main Menu → Configuration → PVC Connections15. PVC Connection Options 1 Source Dlci 15. PVC Connection Options 2 Source EdlciPrimary Destination Link Primary Destination Dlci 15. PVC Connection Options 3 Primary Destination EdlciAlternate Destination Link Alternate Destination Dlci 15. PVC Connection Options 4 Alternate Destination Edlci Configuring the IP Path List Main Menu → Configuration → IP Path List Static16. IP Path List Enter IP Address press ESC to abort ... FWD No Setting Up Management and Communication Options Configuring Node IP Information 17. Node IP Options 1 TS Access Management Link 17. Node IP Options 2 17. Node IP Options 3 TS Management Snmp Validation Configuring Management PVCs 18. Management PVC Options 1 18. Management PVC Options 2 Payload ManagedSet DE 18. Management PVC Options 3 Primary Dlci 18. Management PVC Options 4 Primary Edlci 18. Management PVC Options 5 Alternate DlciAlternate Edlci 18. Management PVC Options 6 Encapsulation Configuring General Snmp Management Name 1 Access19. General Snmp Management Options 1 Snmp Management Configuring Telnet and/or FTP Session Support Name 2 Access19. General Snmp Management Options 2 Telnet Login Required 20. Telnet and FTP Session Options 1Telnet Session 20. Telnet and FTP Session Options 2 Configuring Snmp NMS Security 21. Snmp NMS Security Options 1NMS IP Validation Number of Managers Configuring Snmp Traps and Trap Dial-Out 21. Snmp NMS Security Options 222. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 Link Traps Possible Settings Disable, Up, Down, Both 22. Snmp Traps and Trap Dial-Out Options 3Enterprise Specific Traps Possible Settings Network, Ports, DBM, All, None 22. Snmp Traps and Trap Dial-Out Options 4Dlci Traps on Interfaces Filter Selection Field Rmon Traps Dial-Out Delay TIme Min 22. Snmp Traps and Trap Dial-Out Options 5Trap Dial-Out Trap Disconnect 22. Snmp Traps and Trap Dial-Out Options 6 Alternate Dial-Out DirectoryLatency Traps IP SLV Availability Traps Configuring Ethernet Management 23. Ethernet Management Options 1 23. Ethernet Management Options 2 Proxy ARP Configuring the Communication Port 24. Communication Port Options 1Character Length Login Required 24. Communication Port Options 2Parity Stop Bits 24. Communication Port Options 3 24. Communication Port Options 4 RIP Configuring the Modem Port 10024. Communication Port Options 5 25. Modem Port Options 1 101 25. Modem Port Options 2 102 25. Modem Port Options 3 103 25. Modem Port Options 4 Configuring the Criteria for Automatic Backup Main Menu → Configuration → Auto Backup Criteria26. Auto Backup Criteria Options 1 104 26. Auto Backup Criteria Options 2 When Auto Backup AllowedBackup Allowed Day From nnnn Backup Allowed Day To nnnn 106 Configuring the FrameSaver SLV Router FrameSaver SLV Router Overview Network InterfaceEthernet Address Resolution Protocol IP RoutingProxy ARP Interface Configuration Network Address Translation IP Options ProcessingApplications Supported by NAT NAT Configuration Example NAT Mapping Public IP Addresses Private IP Addresses Save exit Napt Configuration Example Network Address Port TranslationNapt Mapping Public IP Address Private IP Addresses Access-list 1 permit 10.1.3.0 Ip nat inside source list 1 interface se 0.x overloadInt ethernet 0 ip nat inside int serial 0.x ip nat outside NAT and Napt Configuration Example Ip nat inside source static 10.1.1.1 Dynamic Host Configuration Protocol Server Dhcp Server with NAT Configuration Example Public IP Addresses for NAT Private IP Addresses Dhcp Server at Remote Site Configuration Example Dhcp Relay Agent Router Security IP Router FilteringBridge Filtering Provisioning the Router Interface IP FilteringLand Bug Prevention Smurf Attack Prevention Configuring the Router Using Terminal Emulation Security and Logins Limiting Access Controlling Asynchronous Terminal Access Set the configuration option Limiting Dial-In Access via the Modem Port Controlling Isdn Access Disabling Isdn AccessIsdn Call Security Controlling Telnet or FTP Access Limiting Telnet Access Limiting FTP Access Has a Level-1 login and Level-2 telnet access has Controlling Snmp Access Disabling Snmp Access Assigning Snmp Community Names and Access Levels Limiting Snmp Access Through IP Addresses Main Menu → Configuration →General Snmp Management → Snmp Management Enable Management and Communication → Creating a Login Main Menu → Control→ Administer LoginsField Enter Modifying a Login Deleting a Login Controlling Router CLI Access Access Levels Command ModesLargo Changing Access Levels EnableEnable password password End Security and Logins September Operation and Maintenance Operation and Maintenance Displaying System Information Main Menu → Status → IdentityView this field To find Viewing LEDs and Control Leads Isdn DBM FrameSaverTM SLV FrameSaver SLV 9126 LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads Display LEDs & Control Leads Screen for a FrameSaver SLV FrameSaver SLV 9128-II LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads LED Descriptions General Status LEDs 1Label Indiction Color What It Means ALM General Status LEDs 2 ContdModel 9128-II Network, DSX, or PRI Interface LEDs Label Indication Color What It MeansUser Data Port LED CSU/DSUs Only Ethernet Port LED Routers Only Control Lead Descriptions Additional Control Leads Label Indication What It MeansNetwork Interface User Data Port Device Messages Device Messages 1 What It Indicates What To DoSeen at an FTP Terminal Device Messages 2 What It Indicates What To Do See Changing Software on Device Messages 3 What It Indicates What To Do PVC Device Messages 4 What It Indicates What To Do Reset COM Port usage Device Messages 5 What It Indicates What To DoFrameSaver SLV II only Device Messages 6 What It Indicates What To Do Status Information Status Menu Example Last System Reset Date and Time System and Test Status MessagesMain Menu → Status → System and Test Status Self-Test Results Messages Change Operating Mode Health and Status MessagesHealth and Status Messages 1 What It Indicates Isdn PRI DBM only Health and Status Messages 2 What It Indicates Frame relay link 1,2FrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Health and Status Messages 4 What It Indicates Framerelaylink 1,2 Series Access Carrier only Health and Status Messages 5 What It IndicatesPathIP Address Down Nnnn, framerelaylink 1,2 Health and Status Messages 6 What It Indicates Configuration→ Time Slot Assignment → Frame Health and Status Messages 7 What It IndicatesRelay Network Assignments and an LMI failure is Test Status Messages Test Status Messages 1 What It IndicatesDclb Active, framerelaylink 1 or Framerelaylink 1 ,3 Test Status Messages 2 What It Indicates Network LMI-Reported DLCIs Status Main Menu → Status→ LMI Reported DLCIsLMI-Reported DLCIs Status Screen Example Tframe relay network, or IP Path Connection Status Main Menu → Status→ IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates PVC Connection Status Main Menu → Status→ PVC Connection StatusPVC Connection Status Screen Example 12. PVC Connection Status 1 Field What It Indicates MgmtPVCNameEdlci 12. PVC Connection Status 2 Field Status What It Indicates Time Slot Assignment Status Displaying Network Time Slot AssignmentsMain Menu → Status→ Timeslot Assignment Status → Network Network Timeslot Assignment Status Screen Example Cross Connect Status Field bottom Indicates Displaying DSX-1 Time Slot AssignmentsMain Menu → Status→ Timeslot Assignment Status→ DSX-1 DSX-1 Timeslot Assignment Status Screen Example DBM Interface Status Main Menu → Status→ DBM Interface StatusDBM Interface Status Screen Example 13. DBM Interface Status 1 Field What It Indicates Invalid Call ID is displayed Link Name Disabled 13. DBM Interface Status 2 Field What It IndicatesAwarded and Being Delivered In Est Chnl-7 13. DBM Interface Status 3 Field What It Indicates Value is Call AwardedBeing Delivered In Est Chnl-7 Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance IP Routing Table Main Menu → Status→ IP Routing TableIP Routing Table Screen Example 15. IP Routing Table Values 1 Column What It Indicates 15. IP Routing Table Values 2 Column What It Indicates TTL Performance Statistics Main Menu → Status→ Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics Service Level Verification Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Verification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over Service Definitions in , Configuration Options COS ID Size is changed, a new average is not available until a new Dlci Performance Statistics Main Menu → Status → Performance Statistics→ Dlci18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci Frame Relay Performance Statistics Main Menu → Status → Performance Statistics→ Frame RelayFor FrameSaver units with an Isdn DBM 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Errors 20. Frame Relay Performance Statistics 2 What It Indicates 20. Frame Relay Performance Statistics 3 What It Indicates Frame Relay LMI Frame Relay Hdlc Errors 20. Frame Relay Performance Statistics 4 What It Indicates ESF Line Performance Statistics Main Menu → Status → Performance Statistics→ ESF LineTo select intervals You must enter an interval or time on ESF Line Performance Statistics Screen Example Lofc UAS Lofc DBM Call Performance Statistics 22. DBM Call Performance Statistics What It Indicates Ethernet Performance Statistics Main Menu → Status → Performance Statistics → Ethernet23. Ethernet Performance Statistics What It Indicates Trap Event Log Main Menu → Status → Trap Event LogTrap Event Log Screen Example Activating the Modem PassThru Feature Canceling Modem PassThru OperationMain Menu → Control→ Enable Modem PassThru to COM Main Menu → Control→ Disable Modem PassThru to COM Manually Disconnecting the Modem Verifying Modem OperationMain Menu → Control→ Disconnect Modem Forcing Backup Disruptive Isdn DBM Operation Placing a Test Call Nondisruptive Main Menu→ Test→ Isdn Call/PVC TestsIf the Result is Then Verifying That Backup Can Take Place Verifying Isdn LinesSystem Operational should appear FTP File Transfers Command Definition Upgrading System Software If the message displayed is Then Upgrading Isdn BRI DBM Software Main Menu → Status→ Identity Determining Whether a Download Is Completed Changing SoftwareMain Menu → Control→ Select Software Release Transferring Collected Data If retrieving Hen Turning Off the System Alarm Relay Main Menu → Control→ System Alarm Relay Cut-Off Operation and Maintenance September Troubleshooting Problem Indicators Indicators SeeOperation and Maintenance Main Menu → Status → Display LEDs and Control LEDs Resetting the Unit and Restoring Communication Resetting the Unit from the Control MenuResetting the Unit By Cycling the Power Restoring Communication with an Improperly Configured Unit If selecting He following occurs Troubleshooting Management Link Feature LMI Packet Capture Utility Feature LMI Packet Capture Utility→ Display LMI Trace Log LMI Trace Log Example Alarms Alarm Conditions 1 What It Indicates What To DoMenu → Control → Reset Device Alarm Conditions 2 What It Indicates What To Do Main Menu → Configuration → Isdn → Link ProfilesName IPAddress Alarm Conditions 3 What It Indicates What To Do Menu→ Configuration→LMI Down, frame relay Link Alarm Conditions 4 What It Indicates What To Do DTE Alarm Conditions 5 What It Indicates What To Do PathIP Address Alarm Conditions 6 What It Indicates What To Do Nnnn , frame relay Alarm Conditions 7 What It Indicates What To Do Troubleshooting Tables Device ProblemsDevice Problems 1 Symptom Possible Cause Solutions Viewing the Trap Event Log Device Problems 2 Symptom Possible Cause Solutions Improperly Configured Unit on Frame Relay PVC Problems Frame Relay PVC Problems Symptom Possible Cause Solutions Isdn DBM Problems Isdn DBM Problems Symptom Possible Cause SolutionsMain Menu → Status → DBM Interface Status Tests Available Test Menu Example Test Timeout Feature DBM Tests When the status of a test is Only command available is Starting and Stopping a Test Aborting All Tests PVC Tests PVC Tests Screen Example PVC Loopback Main Menu → Test→ Network PVC TestMain Menu → Test→ Data Port PVC Tests Main Menu → Test→ Isdn Call/PVC Tests Send Pattern Monitor PatternNetwork PVC Tests/Data Port PVC Tests Isdn Call/PVC Tests Connectivity Test Call Physical Tests Physical Tests Screen Example Line Loopback Main Menu → Test→ Network Physical TestsLLB Payload Loopback PLB Repeater Loopback RLB AIS DTE Loopback Main Menu → Test→ Data Port Physical TestsDSX Dtlb DTE Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Send Remote Line Loopback Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send and Monitor Pattern Tests Qrss IP Ping Test Ping Screen Example Ping Options 1 Target IP Address Inter-Ping Delay Ping Options 2Source IP Address Packet Size Response Timeout Ping Options 3Ping Responses Field Possible Values Description IP Ping Test Procedure Main Menu → Test→ IP Ping Lamp Test Main Menu → Test→ Lamp Test His chapter includes Setting Up the OpenLane SLM System OpenLane Support of FrameSaver Devices Setting Up FrameSaver Support Ordering SLM Feature Set Activations To Find Your License Key Number Activation Certificate Administering and Managing SLM Activations Entering an Activation Certificate Checking Activation Certificate Status Scheduling Activations Canceling Scheduled Activations Accessing and Printing the Certificate Summary ReportChecking the Status of Scheduled Activations 9128-A2-GB20-80 Setting Up NetScout Manager Plus for FrameSaver Devices 10-1 Alarms Preparation10-2 Properties Configuring NetScout Manager Plus 10-3 10-4 Verifying Domains and Groups 10-5 Correcting Domains and Groups 10-6 Property Description Setting 10-7 Adding SLV Alarms Using a Template 10-8 Editing Alarms 10-9 10-10 Adding SLV Alarms Manually 10-11 10-12 Field Select or EnterParadyne Creating History Files 10-13 10-14 Change 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to Installing the User-Defined History Files Dvuhist -f Dallas51 3 config 30 60 Dallas51k.udhDvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh 10-15 Monitoring a DLCI’s History Data 10-16 10-17 Monitoring the Agent Using NetScout Manager Plus 10-18 10-19 Statistical Windows Supported 10-20Traffic Statistics Protocol Statistics Setting Up Network Health for FrameSaver Devices 11-1 Installation and Setup of Network Health 11-2 Discovering FrameSaver Elements 11-3 Configuring the Discovered Elements 11-4 Grouping Elements for Reports 11-5 About Service Level Reports Generating Reports for a GroupAbout At-a-Glance Reports 11-6 Reports Applicable to SLV Devices About Trend ReportsPrinted Reports 11-7 11-8 11-9 FrameSaver SLV Plus At-a-Glance Report 11-10 Menu Hierarchy Menus Status Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults MIB Support Downloading MIBs and Snmp Traps System Group mib-2 Interfaces Group mib-2FrameSaver Unit’s sysDescr system FrameSaver Unit’s sysObjectID system Frame Relay Logical Layer NAM Profile Link Name FR Service T1 FR NAM NetScout Indexes to the Interface Table ifTableFR DTE T1 FR NAM Rmon Logical Layer IfName of the interfaceNumber Dlci number ALL Number Dlci number DTE Standards Compliance for Snmp Traps Examples Trap authenticationFailure Trap warmStartTable B-3. warmStart Trap What It Indicates Possible Cause Variable-Binding Traps linkUp and linkDown Physical Sublayer PRIMIB Strings BRI Logical Link Sublayer Traps enterprise-Specific Xxx.xxx.xxx.xxx , COS nn Nnnn ’ ‘Path xxx.xxx.xxx.xxx Up That the secondary clock source Traps RMON-Specific Trap dialControl Standard Dial Control MIB Rmon Alarm and Event Defaults Event DefaultsEventIndex EventDescription EventType EventCommunity Dial Control Extension MIB Physical Interface Alarm Defaults Rising Event Operation Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Dlci Alarm Defaults Paradyne Area MIB FR DTE MIB RFC Dlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.2.2.1 6.1.2.1.2.10.32.2.16.1.2.1.16.12.2.1 MIB Rmon II RFC 6.1.4.1.1795.2.24.2 6.1.4.1.1795.2.24.2.6.9.4Dlci CIR CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.4.2 6.1.4.1.1795.2.24.2.6.9.4.5.2.16.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.18.9.1 6.1.2.1.10.32.2.1 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 CLI Commands Convention MeaningX.x Xxxxxxxxxxxx Router CLI Commands, Codes, and Designations Pager Command Access Control CommandsTable C-1. Pager Command Table C-2. Access Control Commands Configuration Commands Table C-3. Configuration CommandsConfigure terminal factory Example configure terminal Interface Commands Table C-4. Interface Commands 1Command Mode config, config-if, config-subif Example interface serial 132.53.4.2 Table C-4. Interface Commands 2 Encapsulation encapsulation-type encapsulation-protocolExample ip address 132.53.4.2 Example encapsulation frame-relay ietf Table C-4. Interface Commands 3 No ip unnumbered nullNo frame-relay interface-dlci dlci-num Example ip unnumbered IP Routing Commands Table C-5. IP Routing CommandsNo ip routing No ip multicast-routing Bridge Commands Table C-6. Bridge Commands 1Example bridge crb 1 route ip Table C-6. Bridge Commands 2 Command Mode config-if, config-subifNo bridge-group bridge-group Example no bridge-group ARP Commands Table C-7. ARP CommandsArp timeout time No arp timeout time Example arp timeout NAT Commands Table C-8. NAT Commands 1Example ip nat translation timeout No ip nat inside outside Table C-8. NAT Commands 2 Ip nat pool pool-name start-ip-addr end-ip-addrNetmask netmask prefix-length / prefix-length No ip nat pool pool-namestart-ip-addr end-ip-addr Table C-8. NAT Commands 3 Clear ip nat translationFrom previous Dhcp Server Commands Table C-9. Dhcp Server Commands 1No service dhcp No ip dhcp pool pool-name Table C-9. Dhcp Server Commands 2 Default-router ip-address No default-router ip-addressDomain-name domain-name No domain-name domain-name Dns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 3 Network network-num Dhcp Relay Agent Commands Table C-10. Dhcp Relay Agent CommandsNo ip dhcp-server ip-address Example ip dhcp relay max-clients Filter access-list Commands Table C-11. Filter Commands 1Access-list access-list-num permit deny No access-list access-list-numpermit deny Table C-11. Filter Commands 2 For Extended IP Access Lists Table C-11. Filter Commands 3 For Protocol Type Access ListsExample access-list 200 permit 0x200 range Table C-11. Filter Commands 4 No ip access-group access-list-1-199numin out Diagnostic Commands Table C-12. Diagnostic Commands 1 Table C-12. Diagnostic Commands 2 Traceroute protocol dest-ipsource source-ip length bytes Show Commands Table C-13. Show Commands 1Show configuration Show arp Table C-13. Show Commands 2 Show configuration saved unsavedShow frame-relay map Show interface intf-type intf-num .sub-intf-num Table C-13. Show Commands 3 Show ip dhcp binding ip-addressShow ip nat translations Show ip route ip-address Table C-13. Show Commands 4 Show ip trafficShow spanning-tree Ethernet Type Codes Table C-14. Ethernet Type Codes Hex 1 Description Table C-14. Ethernet Type Codes Hex 2 Description Protocol and Port Designations Icmp DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations Router Command Line Summaries Shortcuts CLI Summaries Show Command Summary Table D-1. Show Commands FunctionIntf-type intf-num .sub-intf-num Access Control and System Level Command Summary Table D-2. Access Control and System Level Commands Function CLI Command Summary Table D-3. CLI Commands 1Clear counters intf-type intf-num .sub-intf-num Dns-serverip-address Table D-3. CLI Commands 2 Encapsulation encapsulation-type encapsulation-protocol CLI Command Default Settings Connectors, Cables, and Pin Assignments Rear Panels Connectors, Cables, and Pin Assignments Model COM Port Connector Signal Direction Pin #Pin # Signal Direction COM Port for 9126 and 9128-II 25-Position COM Port-to-PC Cable Feature No -F2-550 COM Port for 9128-II Carrier MountCOM Port Non-Keyed Position Modular Plug DB9 Socket COM Port-to-Terminal/Printer Cable Feature No -F2-540 COM Port Non-KeyedPosition Modular Plug DB25 Plug COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin # COM Port AUX Port Signal DB25 Pin # DirectionCOM Port-to-Router Cables Cisco 2500 Series Router RJ45 Jack COM Port Console Port Signal DB25 Pin # Direction DB9 Pin # COM Port AUX Port Signal RJ45 Pin # Direction3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # Gender Adapter/Changer LAN Adapter Converter and CablePlug-to-Modular Jack Converter Com Port Position DB25 Plug DTR RTS DTE Port Connector Direction Pin Socket Standard V.35 Straight-through Cable Standard V.35 Crossover CableMM NN Pin DSX-1 Connector DSX-1 Adapter Feature No -F1-560Function Circuit Direction Pin Number Position DB15 Modular Plug Socket Unkeyed DSX-1 Port for 1-Slot 9128-II 15-Position T1 Network Cable Feature No -F1-500 T1 Mass Termination Cable Feature No -F1-500Function Circuit Line # Pin # Ethernet Port Connector Canadian T1 Line Interface Cable Feature No -F1-510Plug Unkeyed Modem Connector Isdn DBM ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Table F-1. NAM Technical Specifications 1 Criteria Physical DimensionsApprovals Physical Environment Table F-1. NAM Technical Specifications 2 Criteria Table F-1. NAM Technical Specifications 3 Criteria Isdn PRI DBM InterfaceB8ZS Ethernet Port Power Consumption Dissipation Isdn BRI DBM Interface BRI, NI-1Ethernet Port FrameSaver AC Power Requirements Typical Power ConsumptionHeat Dissipation Max Switch Compatibility Service SupportedSwitched Network Interface Standards Compliance Framing Format Coding FormatLine Build-Out LBO Model/Feature EquipmentDescription Number FrameSaver SLV Units Equipment List Isdn PRI DBM FrameSaver SLM Feature Set Upgrade Optional FeaturesPower Supplies NMS Products Series Access Carrier 9128-II NAM only Description Part Number Feature Number Cables Index IN-1 IN-2 BecnCLI IN-3 Dhcp IN-4 DBM IN-5 EEREIR IN-6 IN-7 LANIP SLV IN-8 LOFLOS IN-9 NMS IN-10 OID IN-11 Port IN-12 IN-13 IN-14 IN-15 IN-16