Logging On, Procedure | Paradyne 9128-II, CSU, DSU, 9126-II manual

2. User Interface and Basic Operation

Logging On

Start a session using one of the following methods:

Telnet session via:

—An in-band management channel through the frame relay network.

—A local in-band management channel configured on the DTE port between the FrameSaver unit and the router.

Dial-in connection using the internal modem.

Direct terminal connection over the COM port.

When logging on, the User Interface Idle screen appears.

If no security was set up or security was disabled, the Main Menu screen

Tappears (see Main Menu on page 2-4). You can begin your session.

If security was set up and is enabled, you are prompted for a login. Enter your login ID and password.

When the user interface has been idle, a session is automatically ended and the screen goes blank when the unit times out. Press Enter to reactivate the interface.

Procedure

To log in when security is being enforced:

1.Type your assigned Login ID and press Enter.

2.Type your Password and press Enter.

—Valid characters – All printable ASCII characters

—Number of characters – Up to 10 characters can be entered in the Login ID and Password fields

—Case-sensitive – Yes

An asterisk (*) appears in the password field for each character entered.

2-2

September 2002

9128-A2-GB20-80

Image 30

Paradyne 9128-II, CSU, DSU, 9126-II manual Logging On, Procedure

Contents

FrameSaver SLV Document Feedback Warranty, Sales, Service, and Training InformationCopyright 2002 Paradyne Corporation All rights reserved Trademarks Contents ConfigurationTProcedures Configuration OptionsSeptember Configuring the FrameSaver SLV Router Iii Security and Logins Operation and Maintenance Troubleshooting Lamp Test Menu HierarchyT Setting Up NetScout Manager Plus for FrameSaver DevicesSetting Up Network Health for FrameSaver Devices Vii Snmp MIBs and Traps, and Rmon Alarm Defaults Router CLI TCommands, Codes, and DesignationsViii Router Command Line Summaries and Shortcuts Connectors, Cables, and Pin Assignments Technical Specifications Equipment List Index Purpose and Intended Audience Document OrganizationSection Description Xii Section Description Product-Related Documents XiiiDocument Number Document Title Conventions Used Xiv About the FrameSaver SLV System Overview CSU/DSU-Specific Features Router-Specific Features About the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set FrameSaver SLV Feature Router Maximum Number of PVCs and Management PVCs SupportedThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaverTSLV 9126-II and 9128-II Features Additional FrameSaver SLV 9128-II Features FrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Procedure Logging On If your login was Hen Main Menu Select Screen Work Areas Screen Format Description Navigating the Screens Keyboard KeysPress Function Keys For the screen Select Function Press Enter to Switching Between Screen Areas Selecting from a Menu Screen Contents Selecting a FieldEntering Information Navigating the Router’s CLI CLI Keyboard Keys Configuration Procedures Basic Configuration Configuration Menu Isdn Configuration Option Areas Configuration Option Area Description Accessing and Displaying Configuration Options Main Menu → Configuration Changing Configuration Options Configuration → PVC Connections Saving Configuration Options Configuration Options Configuration Options Using the Easy Install Feature Main Menu → Easy InstallEasy Install Screen Example Using RIP with FrameSaver SLV CSU/DSUs Configuration → Data Ports→ Dlci Records Entering System Information and Setting the System Clock Main Menu → Control→ System InformationIf the selection is Enter Main Menu → Control→ Modem Call Directories Setting Up the ModemSetting Up Call Directories for Trap Dial-Out Valid characters include For Setting Up to Use the Modem PassThru Feature Setting Up Auto-Configuration Main Menu → Auto-ConfigurationAuto-Configuration Screen Example Discovery Mode Configuration Description Selecting a Frame Relay Discovery ModeMain Menu → Auto-Configuration→Frame Relay Discovery Mode Only applies to models with Discovery Mode Configuration Description Automatically Removing a Circuit Setting Up Dial Backup Setting Up the DBM Physical InterfaceMain Menu → Configuration → Isdn → Physical Setting Up Automatic Backup Configuration If you select Then Following prompt When Appears If you select From PVCs Remove AlternateDestinations Delete unused Main Menu → Configuration → Isdn → Link Profiles For Originating a Backup Call For Answering a Backup CallModifying Isdn Link Profiles Restricting Automatic Backup and Configuring Backup Timers Main Menu → Configuration → Auto-Backup Criteria Configuring the DBM Interface to Send Snmp Traps Assigning DLCIs to a Backup Group Changing Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Main Menu → Control→ Change Operating Mode Configuration Option Tables Main Menu → Configuration → System → Frame Relay and LMI Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs System Frame Relay and LMI Options 1 System Frame Relay and LMI Options 2 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Configuring Class of Service Definitions Field Setting After RfcCodePoints Selected Measure Latency & Availability Class of Service DefinitionsClass of Svc Name Code Points Assigned Code Pnt Code Point DefinitionsCode Point Definitions Name SLV Type Available Settings Standard, COS 1-COS Configuring Service Level Verification OptionsService Level Verification Options 1 SLV Sample Interval secs SLV Timeout Error Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Clearing Event Threshold Service Level Verification Options 3 SLV Latency Clearing Event ThresholdSLV Packet Size bytes Test Timeout Configuring General System OptionsMain Menu → Configuration → System→ General General System Options 1 General System Options 2 System Alarm Relay General System Options 3 Main Menu → Configuration → Network→ Physical Configuring Physical InterfacesConfiguring the Network Interface Network Physical Interface Options 1 Bit Stuffing Line Build Out LBO Possible Settings 0.0, -7.5, -15Network Physical Interface Options 2 Transmit Timing Network Initiated PLB Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Physical Interface Options 3 Ansi Performance Report Messages Network Physical Interface Options 4 Circuit Identifier Port Use Possible Settings Frame Relay, Synchronous Data Configuring a User Data Port CSU/DSUsMain Menu → Configuration → Data Ports→ Physical Data Port Physical Interface Options 1 Port Base Rate Kbps Data Port Physical Interface Options 2Max Port Rate Kbps Transmit Clock Source Data Port Physical Interface Options 3 Monitor RTS ControlMonitor DTR Data Port Physical Interface Options 4 Port DTE Initiated LoopbacksInvert Transmit and Receive Data Action on Network Yellow Alarm Data Port Physical Interface Options 5 DSX-1 Physical Interface Options 1 Configuring the DSX-1 InterfaceMain Menu → Configuration → DSX-1 Interface Status DSX-1 Physical Interface Options 2 Send All Ones on DSX-1 Failure Isdn BRI DBM Physical Interface Options Configuring the Isdn DBM InterfaceService Profile ID Spid 1 or Local Phone Number 1 or Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESS 10. Isdn PRI DBM Physical Interface Options 1Local Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 11. Isdn Link Profile Options 1 Setting Up Isdn Link ProfilesMain Menu → Configuration → Isdn → Isdn Link Profiles Link Name Inbound Calling ID 1 or 11. Isdn Link Profile Options 2Outbound Phone Number Maximum Link Rate Kbps Caller Identification Method Assigning Time Slots/Cross Connections11. Isdn Link Profile Options 3 Alternate Outbound Phone Number Assigning Frame Relay Time Slots to the Network Interface Frame Relay Network Time Slot Assignment Screen ExampleValue Meaning Assigning DSX-1 Time Slots to the Network Interface Time Slot Assignment RuleNtt DSX-1 to Network Time Slot Assignment Screen Example Ime Slot Assignment Rules DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Synchronous Data Port Assignment Screen Example Sync Data Port Assignment Clearing Assignments Physical Interface Options Configuring Frame Relay for an Interface 13. Interface Frame Relay Options 1LMI LMI Parameters 13. Interface Frame Relay Options 2Traffic Policing Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 3 Manually Configuring Dlci Records 14. Dlci Record Options 1Dlci Number 14. Dlci Record Options 2 CIR bpsCommitted Burst Size Bc Bits Dlci Priority 14. Dlci Record Options 3Excess Burst Size Bits Outbound Management Priority Backup Group Possible Settings A, B, C, . . . Z, None 14. Dlci Record Options 4 15. PVC Connection Options 1 Configuring PVC ConnectionsMain Menu → Configuration → PVC Connections Source Dlci Primary Destination Link 15. PVC Connection Options 2Source Edlci Primary Destination Dlci Alternate Destination Link 15. PVC Connection Options 3Primary Destination Edlci Alternate Destination Dlci 15. PVC Connection Options 4 Alternate Destination Edlci 16. IP Path List Configuring the IP Path ListMain Menu → Configuration → IP Path List Static Enter IP Address press ESC to abort ... FWD No Setting Up Management and Communication Options Configuring Node IP Information 17. Node IP Options 1 TS Access Management Link 17. Node IP Options 2 17. Node IP Options 3 TS Management Snmp Validation Configuring Management PVCs 18. Management PVC Options 1 18. Management PVC Options 2 Payload ManagedSet DE 18. Management PVC Options 3 Primary Dlci 18. Management PVC Options 4 Primary Edlci 18. Management PVC Options 5 Alternate DlciAlternate Edlci 18. Management PVC Options 6 Encapsulation 19. General Snmp Management Options 1 Configuring General Snmp ManagementName 1 Access Snmp Management Configuring Telnet and/or FTP Session Support Name 2 Access19. General Snmp Management Options 2 Telnet Login Required 20. Telnet and FTP Session Options 1Telnet Session 20. Telnet and FTP Session Options 2 NMS IP Validation Configuring Snmp NMS Security21. Snmp NMS Security Options 1 Number of Managers Configuring Snmp Traps and Trap Dial-Out 21. Snmp NMS Security Options 222. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 Link Traps Possible Settings Disable, Up, Down, Both 22. Snmp Traps and Trap Dial-Out Options 3Enterprise Specific Traps Dlci Traps on Interfaces Filter Selection Field Possible Settings Network, Ports, DBM, All, None22. Snmp Traps and Trap Dial-Out Options 4 Rmon Traps Trap Dial-Out Dial-Out Delay TIme Min22. Snmp Traps and Trap Dial-Out Options 5 Trap Disconnect Latency Traps 22. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory IP SLV Availability Traps Configuring Ethernet Management 23. Ethernet Management Options 1 23. Ethernet Management Options 2 Proxy ARP Configuring the Communication Port 24. Communication Port Options 1Character Length Parity Login Required24. Communication Port Options 2 Stop Bits 24. Communication Port Options 3 24. Communication Port Options 4 RIP 24. Communication Port Options 5 Configuring the Modem Port100 25. Modem Port Options 1 101 25. Modem Port Options 2 102 25. Modem Port Options 3 103 25. Modem Port Options 4 26. Auto Backup Criteria Options 1 Configuring the Criteria for Automatic BackupMain Menu → Configuration → Auto Backup Criteria 104 Backup Allowed Day From nnnn 26. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day To nnnn 106 Configuring the FrameSaver SLV Router FrameSaver SLV Router Overview Network InterfaceEthernet Address Resolution Protocol IP RoutingProxy ARP Interface Configuration Network Address Translation IP Options ProcessingApplications Supported by NAT NAT Configuration Example NAT Mapping Public IP Addresses Private IP Addresses Save exit Napt Configuration Example Network Address Port TranslationNapt Mapping Public IP Address Private IP Addresses Access-list 1 permit 10.1.3.0 Ip nat inside source list 1 interface se 0.x overloadInt ethernet 0 ip nat inside int serial 0.x ip nat outside NAT and Napt Configuration Example Ip nat inside source static 10.1.1.1 Dynamic Host Configuration Protocol Server Dhcp Server with NAT Configuration Example Public IP Addresses for NAT Private IP Addresses Dhcp Server at Remote Site Configuration Example Dhcp Relay Agent Router Security IP Router FilteringBridge Filtering Land Bug Prevention Provisioning the Router InterfaceIP Filtering Smurf Attack Prevention Configuring the Router Using Terminal Emulation Security and Logins Limiting Access Controlling Asynchronous Terminal Access Set the configuration option Limiting Dial-In Access via the Modem Port Controlling Isdn Access Disabling Isdn AccessIsdn Call Security Controlling Telnet or FTP Access Limiting Telnet Access Limiting FTP Access Has a Level-1 login and Level-2 telnet access has Controlling Snmp Access Disabling Snmp Access Assigning Snmp Community Names and Access Levels General Snmp Management → Snmp Management Enable Limiting Snmp Access Through IP AddressesMain Menu → Configuration → Management and Communication → Creating a Login Main Menu → Control→ Administer LoginsField Enter Modifying a Login Deleting a Login Controlling Router CLI Access Access Levels Command ModesLargo Enable password password Changing Access LevelsEnable End Security and Logins September Operation and Maintenance Operation and Maintenance Displaying System Information Main Menu → Status → IdentityView this field To find Viewing LEDs and Control Leads Isdn DBM FrameSaverTM SLV FrameSaver SLV 9126 LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads Display LEDs & Control Leads Screen for a FrameSaver SLV FrameSaver SLV 9128-II LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads Label Indiction Color What It Means LED DescriptionsGeneral Status LEDs 1 ALM Model General Status LEDs 2Contd 9128-II User Data Port LED CSU/DSUs Only Network, DSX, or PRI Interface LEDsLabel Indication Color What It Means Ethernet Port LED Routers Only Network Interface Control Lead DescriptionsAdditional Control Leads Label Indication What It Means User Data Port Seen at an FTP Device MessagesDevice Messages 1 What It Indicates What To Do Terminal Device Messages 2 What It Indicates What To Do See Changing Software on Device Messages 3 What It Indicates What To Do PVC Device Messages 4 What It Indicates What To Do FrameSaver SLV Reset COM Port usageDevice Messages 5 What It Indicates What To Do II only Device Messages 6 What It Indicates What To Do Status Information Status Menu Example Main Menu → Status → System and Test Status Last System Reset Date and TimeSystem and Test Status Messages Self-Test Results Messages Health and Status Messages 1 What It Indicates Change Operating ModeHealth and Status Messages Isdn PRI DBM only Health and Status Messages 2 What It Indicates Frame relay link 1,2FrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Health and Status Messages 4 What It Indicates Framerelaylink 1,2 PathIP Address Down Series Access Carrier onlyHealth and Status Messages 5 What It Indicates Nnnn, framerelaylink 1,2 Health and Status Messages 6 What It Indicates Configuration→ Time Slot Assignment → Frame Health and Status Messages 7 What It IndicatesRelay Network Assignments and an LMI failure is Dclb Active, framerelaylink 1 or Test Status MessagesTest Status Messages 1 What It Indicates Framerelaylink 1 ,3 Test Status Messages 2 What It Indicates Network LMI-Reported DLCIs Status Main Menu → Status→ LMI Reported DLCIsLMI-Reported DLCIs Status Screen Example Tframe relay network, or IP Path Connection Status Main Menu → Status→ IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates PVC Connection Status Main Menu → Status→ PVC Connection StatusPVC Connection Status Screen Example 12. PVC Connection Status 1 Field What It Indicates MgmtPVCNameEdlci 12. PVC Connection Status 2 Field Status What It Indicates Main Menu → Status→ Timeslot Assignment Status → Network Time Slot Assignment StatusDisplaying Network Time Slot Assignments Network Timeslot Assignment Status Screen Example Main Menu → Status→ Timeslot Assignment Status→ DSX-1 Cross Connect Status Field bottom IndicatesDisplaying DSX-1 Time Slot Assignments DSX-1 Timeslot Assignment Status Screen Example DBM Interface Status Main Menu → Status→ DBM Interface StatusDBM Interface Status Screen Example 13. DBM Interface Status 1 Field What It Indicates Invalid Call ID is displayed Awarded and Being Link Name Disabled13. DBM Interface Status 2 Field What It Indicates Delivered In Est Chnl-7 Being Delivered In Est 13. DBM Interface Status 3 Field What It IndicatesValue is Call Awarded Chnl-7 Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance IP Routing Table Screen Example IP Routing TableMain Menu → Status→ IP Routing Table 15. IP Routing Table Values 1 Column What It Indicates 15. IP Routing Table Values 2 Column What It Indicates TTL Performance Statistics Main Menu → Status→ Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics Service Level Verification Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Verification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over Service Definitions in , Configuration Options COS ID Size is changed, a new average is not available until a new Dlci Performance Statistics Main Menu → Status → Performance Statistics→ Dlci18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci For FrameSaver units with an Isdn DBM Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics→ Frame Relay 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Errors 20. Frame Relay Performance Statistics 2 What It Indicates 20. Frame Relay Performance Statistics 3 What It Indicates Frame Relay LMI Frame Relay Hdlc Errors 20. Frame Relay Performance Statistics 4 What It Indicates ESF Line Performance Statistics Main Menu → Status → Performance Statistics→ ESF LineTo select intervals You must enter an interval or time on ESF Line Performance Statistics Screen Example Lofc UAS Lofc DBM Call Performance Statistics 22. DBM Call Performance Statistics What It Indicates Ethernet Performance Statistics Main Menu → Status → Performance Statistics → Ethernet23. Ethernet Performance Statistics What It Indicates Trap Event Log Main Menu → Status → Trap Event LogTrap Event Log Screen Example Main Menu → Control→ Enable Modem PassThru to COM Activating the Modem PassThru FeatureCanceling Modem PassThru Operation Main Menu → Control→ Disable Modem PassThru to COM Manually Disconnecting the Modem Verifying Modem OperationMain Menu → Control→ Disconnect Modem Forcing Backup Disruptive Isdn DBM Operation Placing a Test Call Nondisruptive Main Menu→ Test→ Isdn Call/PVC TestsIf the Result is Then Verifying That Backup Can Take Place Verifying Isdn LinesSystem Operational should appear FTP File Transfers Command Definition Upgrading System Software If the message displayed is Then Upgrading Isdn BRI DBM Software Main Menu → Status→ Identity Determining Whether a Download Is Completed Changing SoftwareMain Menu → Control→ Select Software Release Transferring Collected Data If retrieving Hen Turning Off the System Alarm Relay Main Menu → Control→ System Alarm Relay Cut-Off Operation and Maintenance September Troubleshooting Operation and Maintenance Problem IndicatorsIndicators See Main Menu → Status → Display LEDs and Control LEDs Resetting the Unit and Restoring Communication Resetting the Unit from the Control MenuResetting the Unit By Cycling the Power Restoring Communication with an Improperly Configured Unit If selecting He following occurs Troubleshooting Management Link Feature LMI Packet Capture Utility Feature LMI Packet Capture Utility→ Display LMI Trace Log LMI Trace Log Example Alarms Alarm Conditions 1 What It Indicates What To DoMenu → Control → Reset Device Name Alarm Conditions 2 What It Indicates What To DoMain Menu → Configuration → Isdn → Link Profiles IPAddress LMI Down, frame relay Alarm Conditions 3 What It Indicates What To DoMenu→ Configuration→ Link Alarm Conditions 4 What It Indicates What To Do DTE Alarm Conditions 5 What It Indicates What To Do PathIP Address Alarm Conditions 6 What It Indicates What To Do Nnnn , frame relay Alarm Conditions 7 What It Indicates What To Do Device Problems 1 Symptom Possible Cause Solutions Troubleshooting TablesDevice Problems Viewing the Trap Event Log Device Problems 2 Symptom Possible Cause Solutions Improperly Configured Unit on Frame Relay PVC Problems Frame Relay PVC Problems Symptom Possible Cause Solutions Isdn DBM Problems Isdn DBM Problems Symptom Possible Cause SolutionsMain Menu → Status → DBM Interface Status Tests Available Test Menu Example Test Timeout Feature DBM Tests When the status of a test is Only command available is Starting and Stopping a Test Aborting All Tests PVC Tests PVC Tests Screen Example Main Menu → Test→ Data Port PVC Tests PVC LoopbackMain Menu → Test→ Network PVC Test Main Menu → Test→ Isdn Call/PVC Tests Network PVC Tests/Data Port PVC Tests Send PatternMonitor Pattern Isdn Call/PVC Tests Connectivity Test Call Physical Tests Physical Tests Screen Example Line Loopback Main Menu → Test→ Network Physical TestsLLB Payload Loopback PLB Repeater Loopback RLB AIS DSX DTE LoopbackMain Menu → Test→ Data Port Physical Tests Dtlb DTE Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Send Remote Line Loopback Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send and Monitor Pattern Tests Qrss IP Ping Test Ping Screen Example Ping Options 1 Target IP Address Source IP Address Inter-Ping DelayPing Options 2 Packet Size Response Timeout Ping Options 3Ping Responses Field Possible Values Description IP Ping Test Procedure Main Menu → Test→ IP Ping Lamp Test Main Menu → Test→ Lamp Test His chapter includes Setting Up the OpenLane SLM System OpenLane Support of FrameSaver Devices Setting Up FrameSaver Support Ordering SLM Feature Set Activations To Find Your License Key Number Activation Certificate Administering and Managing SLM Activations Entering an Activation Certificate Checking Activation Certificate Status Scheduling Activations Canceling Scheduled Activations Accessing and Printing the Certificate Summary ReportChecking the Status of Scheduled Activations 9128-A2-GB20-80 Setting Up NetScout Manager Plus for FrameSaver Devices 10-1 10-2 AlarmsPreparation Properties Configuring NetScout Manager Plus 10-3 10-4 Verifying Domains and Groups 10-5 Correcting Domains and Groups 10-6 Property Description Setting 10-7 Adding SLV Alarms Using a Template 10-8 Editing Alarms 10-9 10-10 Adding SLV Alarms Manually 10-11 10-12 Field Select or EnterParadyne Creating History Files 10-13 10-14 Change 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to Dvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh Installing the User-Defined History FilesDvuhist -f Dallas51 3 config 30 60 Dallas51k.udh 10-15 Monitoring a DLCI’s History Data 10-16 10-17 Monitoring the Agent Using NetScout Manager Plus 10-18 10-19 Statistical Windows Supported 10-20Traffic Statistics Protocol Statistics Setting Up Network Health for FrameSaver Devices 11-1 Installation and Setup of Network Health 11-2 Discovering FrameSaver Elements 11-3 Configuring the Discovered Elements 11-4 Grouping Elements for Reports 11-5 About At-a-Glance Reports About Service Level ReportsGenerating Reports for a Group 11-6 Printed Reports Reports Applicable to SLV DevicesAbout Trend Reports 11-7 11-8 11-9 FrameSaver SLV Plus At-a-Glance Report 11-10 Menu Hierarchy Menus Status Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults MIB Support Downloading MIBs and Snmp Traps FrameSaver Unit’s sysDescr system System Group mib-2Interfaces Group mib-2 FrameSaver Unit’s sysObjectID system Frame Relay Logical Layer NAM Profile Link Name FR Service T1 FR NAM NetScout Indexes to the Interface Table ifTableFR DTE T1 FR NAM Number Dlci number ALL Rmon Logical LayerIfName of the interface Number Dlci number DTE Standards Compliance for Snmp Traps Examples Table B-3. warmStart Trap What It Indicates Possible Cause Trap authenticationFailureTrap warmStart Variable-Binding Traps linkUp and linkDown MIB Physical SublayerPRI Strings BRI Logical Link Sublayer Traps enterprise-Specific Xxx.xxx.xxx.xxx , COS nn Nnnn ’ ‘Path xxx.xxx.xxx.xxx Up That the secondary clock source Traps RMON-Specific Trap dialControl Standard Dial Control MIB EventIndex EventDescription EventType EventCommunity Rmon Alarm and Event DefaultsEvent Defaults Dial Control Extension MIB Physical Interface Alarm Defaults Rising Event Operation Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults Dlci Alarm Defaults Paradyne Area MIB FR DTE MIB RFC Dlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order 6.1.2.1.16.12.2.1 6.1.2.1.2.2.16.1.2.1.2.10.32.2.1 MIB Rmon II RFC Dlci CIR 6.1.4.1.1795.2.24.26.1.4.1.1795.2.24.2.6.9.4 CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.4.2 6.1.4.1.1795.2.24.2.6.9.4.5.2.16.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.18.9.1 6.1.2.1.10.32.2.1 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 X.x CLI CommandsConvention Meaning Xxxxxxxxxxxx Router CLI Commands, Codes, and Designations Table C-1. Pager Command Pager CommandAccess Control Commands Table C-2. Access Control Commands Configure terminal factory Configuration CommandsTable C-3. Configuration Commands Example configure terminal Command Mode config, config-if, config-subif Interface CommandsTable C-4. Interface Commands 1 Example interface serial 132.53.4.2 Example ip address 132.53.4.2 Table C-4. Interface Commands 2Encapsulation encapsulation-type encapsulation-protocol Example encapsulation frame-relay ietf No frame-relay interface-dlci dlci-num Table C-4. Interface Commands 3No ip unnumbered null Example ip unnumbered No ip routing IP Routing CommandsTable C-5. IP Routing Commands No ip multicast-routing Bridge Commands Table C-6. Bridge Commands 1Example bridge crb 1 route ip No bridge-group bridge-group Table C-6. Bridge Commands 2Command Mode config-if, config-subif Example no bridge-group Arp timeout time No arp timeout time ARP CommandsTable C-7. ARP Commands Example arp timeout Example ip nat translation timeout NAT CommandsTable C-8. NAT Commands 1 No ip nat inside outside Netmask netmask prefix-length / prefix-length Table C-8. NAT Commands 2Ip nat pool pool-name start-ip-addr end-ip-addr No ip nat pool pool-namestart-ip-addr end-ip-addr Table C-8. NAT Commands 3 Clear ip nat translationFrom previous No service dhcp Dhcp Server CommandsTable C-9. Dhcp Server Commands 1 No ip dhcp pool pool-name Domain-name domain-name No domain-name domain-name Table C-9. Dhcp Server Commands 2Default-router ip-address No default-router ip-address Dns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 3 Network network-num No ip dhcp-server ip-address Dhcp Relay Agent CommandsTable C-10. Dhcp Relay Agent Commands Example ip dhcp relay max-clients Access-list access-list-num permit deny Filter access-list CommandsTable C-11. Filter Commands 1 No access-list access-list-numpermit deny Table C-11. Filter Commands 2 For Extended IP Access Lists Table C-11. Filter Commands 3 For Protocol Type Access ListsExample access-list 200 permit 0x200 range Table C-11. Filter Commands 4 No ip access-group access-list-1-199numin out Diagnostic Commands Table C-12. Diagnostic Commands 1 Table C-12. Diagnostic Commands 2 Traceroute protocol dest-ipsource source-ip length bytes Show configuration Show CommandsTable C-13. Show Commands 1 Show arp Show frame-relay map Table C-13. Show Commands 2Show configuration saved unsaved Show interface intf-type intf-num .sub-intf-num Show ip nat translations Table C-13. Show Commands 3Show ip dhcp binding ip-address Show ip route ip-address Table C-13. Show Commands 4 Show ip trafficShow spanning-tree Ethernet Type Codes Table C-14. Ethernet Type Codes Hex 1 Description Table C-14. Ethernet Type Codes Hex 2 Description Protocol and Port Designations Icmp DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations Router Command Line Summaries Shortcuts CLI Summaries Show Command Summary Table D-1. Show Commands FunctionIntf-type intf-num .sub-intf-num Access Control and System Level Command Summary Table D-2. Access Control and System Level Commands Function Clear counters intf-type intf-num .sub-intf-num CLI Command SummaryTable D-3. CLI Commands 1 Dns-serverip-address Table D-3. CLI Commands 2 Encapsulation encapsulation-type encapsulation-protocol CLI Command Default Settings Connectors, Cables, and Pin Assignments Rear Panels Connectors, Cables, and Pin Assignments Model Pin # Signal Direction COM Port ConnectorSignal Direction Pin # COM Port for 9126 and 9128-II 25-Position COM Port Non-Keyed Position COM Port-to-PC Cable Feature No -F2-550COM Port for 9128-II Carrier Mount Modular Plug DB9 Socket COM Port-to-Terminal/Printer Cable Feature No -F2-540 COM Port Non-KeyedPosition Modular Plug DB25 Plug COM Port-to-Router Cables COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port AUX Port Signal DB25 Pin # Direction Cisco 2500 Series Router RJ45 Jack COM Port Console Port Signal DB25 Pin # Direction DB9 Pin # COM Port AUX Port Signal RJ45 Pin # Direction3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # Plug-to-Modular Jack Converter Com Port Position DB25 Plug Gender Adapter/ChangerLAN Adapter Converter and Cable DTR RTS DTE Port Connector Direction Pin Socket MM NN Standard V.35 Straight-through CableStandard V.35 Crossover Cable Pin Function Circuit Direction Pin Number DSX-1 ConnectorDSX-1 Adapter Feature No -F1-560 Position DB15 Modular Plug Socket Unkeyed DSX-1 Port for 1-Slot 9128-II 15-Position T1 Network Cable Feature No -F1-500 T1 Mass Termination Cable Feature No -F1-500Function Circuit Line # Pin # Ethernet Port Connector Canadian T1 Line Interface Cable Feature No -F1-510Plug Unkeyed Modem Connector Isdn DBM ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Approvals Table F-1. NAM Technical Specifications 1 CriteriaPhysical Dimensions Physical Environment Table F-1. NAM Technical Specifications 2 Criteria B8ZS Table F-1. NAM Technical Specifications 3 CriteriaIsdn PRI DBM Interface Ethernet Port Power Consumption Dissipation Isdn BRI DBM Interface BRI, NI-1Ethernet Port FrameSaver AC Power Requirements Typical Power ConsumptionHeat Dissipation Max Switched Network Interface Switch CompatibilityService Supported Standards Compliance Framing Format Coding FormatLine Build-Out LBO Description Number Model/FeatureEquipment FrameSaver SLV Units Equipment List Isdn PRI DBM Power Supplies FrameSaver SLM Feature Set UpgradeOptional Features NMS Products Series Access Carrier 9128-II NAM only Description Part Number Feature Number Cables Index IN-1 IN-2 BecnCLI IN-3 Dhcp IN-4 DBM IN-5 EEREIR IN-6 IN-7 LANIP SLV IN-8 LOFLOS IN-9 NMS IN-10 OID IN-11 Port IN-12 IN-13 IN-14 IN-15 IN-16