Upgrading System Software

7. Operation and Maintenance

If you need to upgrade the FrameSaver unit’s program code, you must transfer the upgrade of the nam.ocd file in the system memory directory using the put command.

NOTE:

Upgrades can be performed through the network using a Management PVC, or through the COM port if Port Use is set to Net Link (see Table 4-23, Ethernet Management Options, in Chapter 4, Configuration Options).

Procedure

To download software:

1.Initiate an FTP session to the device that you are upgrading.

2.Type bin to enter binary transfer mode.

3.Type hash to enter hash mode if you want to monitor the progress of the upgrade, provided this function is supported by your equipment.

4.Type cd system to change to the system directory.

5.Perform a put of Rxxxxxx.ocd (xxxxxx being the software release number) to the nam.ocd file to start the upgrade.

If the message displayed is . . .	Then . . .

nam.ocd: File Transfer Complete	The download was successful. The file is loaded
	into system memory.

nam.ocd: File Transfer Failed –	The file is not valid for this FrameSaver unit.
Invalid file	A different Rxxxxxx.ocd file will need to be
	A different Rxxxxxx.ocd file will need to be
	downloaded. Repeat the step or end the FTP
	session.

NOTE:

During the download, a series of hash marks (#) appear. When the hash marks stop appearing, there is a pause of about 30 seconds before the nam.ocd: File Transfer Complete message appears. Please be patient. Do not exit from FTP at this time.

See Changing Software on page 7-79to activate the newly downloaded software.

9128-A2-GB20-80

September 2002

7-77

Page 259

Image 259

Paradyne CSU, DSU, 9126-II, 9128-II manual Upgrading System Software, If the message displayed is Then

Contents

FrameSaver SLV Trademarks Warranty, Sales, Service, and Training InformationCopyright 2002 Paradyne Corporation All rights reserved Document Feedback Contents Configuration Options ConfigurationTProceduresSeptember Iii Configuring the FrameSaver SLV Router Operation and Maintenance Security and Logins Troubleshooting Lamp Test Vii Setting Up NetScout Manager Plus for FrameSaver DevicesSetting Up Network Health for FrameSaver Devices Menu HierarchyT Router CLI TCommands, Codes, and Designations Snmp MIBs and Traps, and Rmon Alarm DefaultsViii Connectors, Cables, and Pin Assignments Router Command Line Summaries and Shortcuts Index Technical Specifications Equipment List Document Organization Purpose and Intended AudienceSection Description Section Description Xii Xiii Product-Related DocumentsDocument Number Document Title Xiv Conventions Used System Overview About the FrameSaver SLV Router-Specific Features CSU/DSU-Specific Features About the FrameSaver SLV FrameSaver Diagnostic and SLM Feature Sets FrameSaver Diagnostic Feature Set Maximum Number of PVCs and Management PVCs Supported FrameSaver SLV Feature RouterThrough 120 Connections PVCs Dedicated Management About the FrameSaver SLV About the FrameSaver SLV Additional FrameSaver SLV 9128-II Features Additional FrameSaverTSLV 9126-II and 9128-II Features FrameSaver SLM Feature Set OpenLane SLM System NetScout Manager Plus and NetScout Probes User Interface and Basic Operation Logging On Procedure If your login was Hen Select Main Menu Screen Format Description Screen Work Areas Keyboard Keys Navigating the ScreensPress For the screen Select Function Press Enter to Function Keys Selecting from a Menu Switching Between Screen Areas Selecting a Field Screen ContentsEntering Information CLI Keyboard Keys Navigating the Router’s CLI Basic Configuration Configuration Procedures Isdn Configuration Menu Configuration Option Area Description Configuration Option Areas Main Menu → Configuration Accessing and Displaying Configuration Options Configuration → PVC Connections Changing Configuration Options Saving Configuration Options Configuration Options Configuration Options Main Menu → Easy Install Using the Easy Install FeatureEasy Install Screen Example Configuration → Data Ports→ Dlci Records Using RIP with FrameSaver SLV CSU/DSUs Main Menu → Control→ System Information Entering System Information and Setting the System ClockIf the selection is Enter Valid characters include For Setting Up the ModemSetting Up Call Directories for Trap Dial-Out Main Menu → Control→ Modem Call Directories Setting Up to Use the Modem PassThru Feature Main Menu → Auto-Configuration Setting Up Auto-ConfigurationAuto-Configuration Screen Example Only applies to models with Selecting a Frame Relay Discovery ModeMain Menu → Auto-Configuration→Frame Relay Discovery Mode Discovery Mode Configuration Description Discovery Mode Configuration Description Automatically Removing a Circuit Setting Up the DBM Physical Interface Setting Up Dial BackupMain Menu → Configuration → Isdn → Physical If you select Then Setting Up Automatic Backup Configuration Following prompt When Appears If you select Delete unused Remove AlternateDestinations From PVCs For Originating a Backup Call For Answering a Backup Call Main Menu → Configuration → Isdn → Link ProfilesModifying Isdn Link Profiles Main Menu → Configuration → Auto-Backup Criteria Restricting Automatic Backup and Configuring Backup Timers Assigning DLCIs to a Backup Group Configuring the DBM Interface to Send Snmp Traps Main Menu → Control→ Change Operating Mode PVC Backup Over the Network InterfaceSetting Up Back-to-Back Operation Changing Operating Mode Configuration Option Tables System Frame Relay and LMI Options 1 Configuring the Overall SystemConfiguring Frame Relay and LMI for the System CSU/DSUs Main Menu → Configuration → System → Frame Relay and LMI System Frame Relay and LMI Options 2 LMI Heartbeat T1 Possible Settings 5, 10, 15, 20, 25 LMI Status Enquiry N1 Possible Settings 1, 2, 3, 4System Frame Relay and LMI Options 3 System Frame Relay and LMI Options 4 Field Setting After RfcCodePoints Selected Configuring Class of Service Definitions Code Points Assigned Class of Service DefinitionsClass of Svc Name Measure Latency & Availability Name Code Point DefinitionsCode Point Definitions Code Pnt SLV Sample Interval secs Configuring Service Level Verification OptionsService Level Verification Options 1 SLV Type Available Settings Standard, COS 1-COS SLV Timeout Clearing Event Threshold Service Level Verification Options 2Dlci Down on SLV Timeout SLV Timeout Error Event Threshold SLV Latency Clearing Event Threshold Service Level Verification Options 3SLV Packet Size bytes General System Options 1 Configuring General System OptionsMain Menu → Configuration → System→ General Test Timeout General System Options 2 General System Options 3 System Alarm Relay Network Physical Interface Options 1 Configuring Physical InterfacesConfiguring the Network Interface Main Menu → Configuration → Network→ Physical Transmit Timing Line Build Out LBO Possible Settings 0.0, -7.5, -15Network Physical Interface Options 2 Bit Stuffing Ansi Performance Report Messages Network Initiated Dclb Possible Settings Disable, V.54&ANSINetwork Physical Interface Options 3 Network Initiated PLB Circuit Identifier Network Physical Interface Options 4 Data Port Physical Interface Options 1 Configuring a User Data Port CSU/DSUsMain Menu → Configuration → Data Ports→ Physical Port Use Possible Settings Frame Relay, Synchronous Data Transmit Clock Source Data Port Physical Interface Options 2Max Port Rate Kbps Port Base Rate Kbps Monitor RTS Control Data Port Physical Interface Options 3Monitor DTR Port DTE Initiated Loopbacks Data Port Physical Interface Options 4Invert Transmit and Receive Data Data Port Physical Interface Options 5 Action on Network Yellow Alarm Interface Status Configuring the DSX-1 InterfaceMain Menu → Configuration → DSX-1 DSX-1 Physical Interface Options 1 Send All Ones on DSX-1 Failure DSX-1 Physical Interface Options 2 Local Phone Number 1 or Configuring the Isdn DBM InterfaceService Profile ID Spid 1 or Isdn BRI DBM Physical Interface Options 10. Isdn PRI DBM Physical Interface Options 1 Switch Type Possible Settings NI-2, ATT4ESS, ATT5ESSLocal Phone Number 10. Isdn PRI DBM Physical Interface Options 2 10. Isdn PRI DBM Physical Interface Options 3 Link Name Setting Up Isdn Link ProfilesMain Menu → Configuration → Isdn → Isdn Link Profiles 11. Isdn Link Profile Options 1 Maximum Link Rate Kbps 11. Isdn Link Profile Options 2Outbound Phone Number Inbound Calling ID 1 or Alternate Outbound Phone Number Assigning Time Slots/Cross Connections11. Isdn Link Profile Options 3 Caller Identification Method Frame Relay Network Time Slot Assignment Screen Example Assigning Frame Relay Time Slots to the Network InterfaceValue Meaning Time Slot Assignment Rule Assigning DSX-1 Time Slots to the Network InterfaceNtt Ime Slot Assignment Rules DSX-1 to Network Time Slot Assignment Screen Example DSX-1 Signaling Assignments and Trunk Conditioning RBS Idle PLAR3idle Sync Data Port Assignment Synchronous Data Port Assignment Screen Example Physical Interface Options Clearing Assignments 13. Interface Frame Relay Options 1 Configuring Frame Relay for an InterfaceLMI Frame Relay DS0s Base Rate 13. Interface Frame Relay Options 2Traffic Policing LMI Parameters 13. Interface Frame Relay Options 3 14. Dlci Record Options 1 Manually Configuring Dlci RecordsDlci Number CIR bps 14. Dlci Record Options 2Committed Burst Size Bc Bits Outbound Management Priority 14. Dlci Record Options 3Excess Burst Size Bits Dlci Priority 14. Dlci Record Options 4 Backup Group Possible Settings A, B, C, . . . Z, None Source Dlci Configuring PVC ConnectionsMain Menu → Configuration → PVC Connections 15. PVC Connection Options 1 Primary Destination Dlci 15. PVC Connection Options 2Source Edlci Primary Destination Link Alternate Destination Dlci 15. PVC Connection Options 3Primary Destination Edlci Alternate Destination Link Alternate Destination Edlci 15. PVC Connection Options 4 Enter IP Address press ESC to abort ... FWD No Configuring the IP Path ListMain Menu → Configuration → IP Path List Static 16. IP Path List Setting Up Management and Communication Options 17. Node IP Options 1 Configuring Node IP Information 17. Node IP Options 2 TS Access Management Link TS Management Snmp Validation 17. Node IP Options 3 18. Management PVC Options 1 Configuring Management PVCs Payload Managed 18. Management PVC Options 2Set DE Primary Dlci 18. Management PVC Options 3 Primary Edlci 18. Management PVC Options 4 Alternate Dlci 18. Management PVC Options 5Alternate Edlci Encapsulation 18. Management PVC Options 6 Snmp Management Configuring General Snmp ManagementName 1 Access 19. General Snmp Management Options 1 Name 2 Access Configuring Telnet and/or FTP Session Support19. General Snmp Management Options 2 20. Telnet and FTP Session Options 1 Telnet Login RequiredTelnet Session 20. Telnet and FTP Session Options 2 Number of Managers Configuring Snmp NMS Security21. Snmp NMS Security Options 1 NMS IP Validation 21. Snmp NMS Security Options 2 Configuring Snmp Traps and Trap Dial-Out22. Snmp Traps and Trap Dial-Out Options 1 22. Snmp Traps and Trap Dial-Out Options 2 22. Snmp Traps and Trap Dial-Out Options 3 Link Traps Possible Settings Disable, Up, Down, BothEnterprise Specific Traps Rmon Traps Possible Settings Network, Ports, DBM, All, None22. Snmp Traps and Trap Dial-Out Options 4 Dlci Traps on Interfaces Filter Selection Field Trap Disconnect Dial-Out Delay TIme Min22. Snmp Traps and Trap Dial-Out Options 5 Trap Dial-Out IP SLV Availability Traps 22. Snmp Traps and Trap Dial-Out Options 6Alternate Dial-Out Directory Latency Traps 23. Ethernet Management Options 1 Configuring Ethernet Management Proxy ARP 23. Ethernet Management Options 2 24. Communication Port Options 1 Configuring the Communication PortCharacter Length Stop Bits Login Required24. Communication Port Options 2 Parity 24. Communication Port Options 3 RIP 24. Communication Port Options 4 25. Modem Port Options 1 Configuring the Modem Port100 24. Communication Port Options 5 25. Modem Port Options 2 101 25. Modem Port Options 3 102 25. Modem Port Options 4 103 104 Configuring the Criteria for Automatic BackupMain Menu → Configuration → Auto Backup Criteria 26. Auto Backup Criteria Options 1 Backup Allowed Day To nnnn 26. Auto Backup Criteria Options 2When Auto Backup Allowed Backup Allowed Day From nnnn 106 Configuring the FrameSaver SLV Router Network Interface FrameSaver SLV Router OverviewEthernet IP Routing Address Resolution ProtocolProxy ARP Interface Configuration IP Options Processing Network Address TranslationApplications Supported by NAT NAT Mapping Public IP Addresses Private IP Addresses NAT Configuration Example Save exit Network Address Port Translation Napt Configuration ExampleNapt Mapping Public IP Address Private IP Addresses Ip nat inside source list 1 interface se 0.x overload Access-list 1 permit 10.1.3.0Int ethernet 0 ip nat inside int serial 0.x ip nat outside Ip nat inside source static 10.1.1.1 NAT and Napt Configuration Example Dynamic Host Configuration Protocol Server Public IP Addresses for NAT Private IP Addresses Dhcp Server with NAT Configuration Example Dhcp Relay Agent Dhcp Server at Remote Site Configuration Example IP Router Filtering Router SecurityBridge Filtering Smurf Attack Prevention Provisioning the Router InterfaceIP Filtering Land Bug Prevention Configuring the Router Using Terminal Emulation Security and Logins Controlling Asynchronous Terminal Access Limiting Access Set the configuration option Limiting Dial-In Access via the Modem Port Disabling Isdn Access Controlling Isdn AccessIsdn Call Security Limiting Telnet Access Controlling Telnet or FTP Access Limiting FTP Access Has a Level-1 login and Level-2 telnet access has Disabling Snmp Access Controlling Snmp Access Assigning Snmp Community Names and Access Levels Management and Communication → Limiting Snmp Access Through IP AddressesMain Menu → Configuration → General Snmp Management → Snmp Management Enable Main Menu → Control→ Administer Logins Creating a LoginField Enter Deleting a Login Modifying a Login Access Levels Command Modes Controlling Router CLI AccessLargo End Changing Access LevelsEnable Enable password password Security and Logins September Operation and Maintenance Operation and Maintenance Main Menu → Status → Identity Displaying System InformationView this field To find Isdn DBM Viewing LEDs and Control Leads FrameSaver SLV 9126 LEDs and Control Leads FrameSaverTM SLV Display LEDs & Control Leads Screen for a FrameSaver SLV Main Menu → Status → Display LEDs and Control Leads Main Menu → Status → Display LEDs and Control Leads FrameSaver SLV 9128-II LEDs and Control Leads ALM LED DescriptionsGeneral Status LEDs 1 Label Indiction Color What It Means 9128-II General Status LEDs 2Contd Model Ethernet Port LED Routers Only Network, DSX, or PRI Interface LEDsLabel Indication Color What It Means User Data Port LED CSU/DSUs Only User Data Port Control Lead DescriptionsAdditional Control Leads Label Indication What It Means Network Interface Terminal Device MessagesDevice Messages 1 What It Indicates What To Do Seen at an FTP See Changing Software on Device Messages 2 What It Indicates What To Do PVC Device Messages 3 What It Indicates What To Do Device Messages 4 What It Indicates What To Do II only Reset COM Port usageDevice Messages 5 What It Indicates What To Do FrameSaver SLV Device Messages 6 What It Indicates What To Do Status Menu Example Status Information Self-Test Results Messages Last System Reset Date and TimeSystem and Test Status Messages Main Menu → Status → System and Test Status Isdn PRI DBM only Change Operating ModeHealth and Status Messages Health and Status Messages 1 What It Indicates Frame relay link 1,2 Health and Status Messages 2 What It IndicatesFrameSaver SLV 9126-II or Health and Status Messages 3 What It Indicates Framerelaylink 1,2 Health and Status Messages 4 What It Indicates Nnnn, framerelaylink 1,2 Series Access Carrier onlyHealth and Status Messages 5 What It Indicates PathIP Address Down Health and Status Messages 6 What It Indicates Health and Status Messages 7 What It Indicates Configuration→ Time Slot Assignment → FrameRelay Network Assignments and an LMI failure is Framerelaylink 1 ,3 Test Status MessagesTest Status Messages 1 What It Indicates Dclb Active, framerelaylink 1 or Test Status Messages 2 What It Indicates Main Menu → Status→ LMI Reported DLCIs Network LMI-Reported DLCIs StatusLMI-Reported DLCIs Status Screen Example Tframe relay network, or Main Menu → Status→ IP Path Connection Status IP Path Connection StatusIP Path Connection Status Screen Example 11. IP Path Connection Status Field What It Indicates Main Menu → Status→ PVC Connection Status PVC Connection StatusPVC Connection Status Screen Example MgmtPVCName 12. PVC Connection Status 1 Field What It IndicatesEdlci Status What It Indicates 12. PVC Connection Status 2 Field Network Timeslot Assignment Status Screen Example Time Slot Assignment StatusDisplaying Network Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status → Network DSX-1 Timeslot Assignment Status Screen Example Cross Connect Status Field bottom IndicatesDisplaying DSX-1 Time Slot Assignments Main Menu → Status→ Timeslot Assignment Status→ DSX-1 Main Menu → Status→ DBM Interface Status DBM Interface StatusDBM Interface Status Screen Example Invalid Call ID is displayed 13. DBM Interface Status 1 Field What It Indicates Delivered In Est Chnl-7 Link Name Disabled13. DBM Interface Status 2 Field What It Indicates Awarded and Being Chnl-7 13. DBM Interface Status 3 Field What It IndicatesValue is Call Awarded Being Delivered In Est Most Recent and Previous Cause Value Messages Make sure the network is Operation and Maintenance Normal class applies for this Correct number Operation and Maintenance 15. IP Routing Table Values 1 Column What It Indicates IP Routing TableMain Menu → Status→ IP Routing Table IP Routing Table Screen Example TTL 15. IP Routing Table Values 2 Column What It Indicates Main Menu → Status→ Performance Statistics Performance StatisticsPerformance Statistics Menu Clearing Performance Statistics 17, SLV Performance Statistics for IP Enabled Dlci Service Level Verification Performance Statistics Verification Options, in , Configuration Options, must Verification Options, in , Configuration Options, over COS ID Service Definitions in , Configuration Options Size is changed, a new average is not available until a new Main Menu → Status → Performance Statistics→ Dlci Dlci Performance Statistics18. Dlci Performance Statistics 1 What It Indicates 18. Dlci Performance Statistics 2 What It Indicates Additional Performance Statistics for IP Enabled Dlci 20. Frame Relay Performance Statistics 1 What It Indicates Frame Relay Performance StatisticsMain Menu → Status → Performance Statistics→ Frame Relay For FrameSaver units with an Isdn DBM 20. Frame Relay Performance Statistics 2 What It Indicates Frame Relay Errors Frame Relay LMI 20. Frame Relay Performance Statistics 3 What It Indicates 20. Frame Relay Performance Statistics 4 What It Indicates Frame Relay Hdlc Errors Main Menu → Status → Performance Statistics→ ESF Line ESF Line Performance StatisticsTo select intervals You must enter an interval or time on Lofc ESF Line Performance Statistics Screen Example Lofc UAS 22. DBM Call Performance Statistics What It Indicates DBM Call Performance Statistics Main Menu → Status → Performance Statistics → Ethernet Ethernet Performance Statistics23. Ethernet Performance Statistics What It Indicates Main Menu → Status → Trap Event Log Trap Event LogTrap Event Log Screen Example Main Menu → Control→ Disable Modem PassThru to COM Activating the Modem PassThru FeatureCanceling Modem PassThru Operation Main Menu → Control→ Enable Modem PassThru to COM Verifying Modem Operation Manually Disconnecting the ModemMain Menu → Control→ Disconnect Modem Isdn DBM Operation Forcing Backup Disruptive Main Menu→ Test→ Isdn Call/PVC Tests Placing a Test Call NondisruptiveIf the Result is Then Verifying Isdn Lines Verifying That Backup Can Take PlaceSystem Operational should appear FTP File Transfers Command Definition If the message displayed is Then Upgrading System Software Main Menu → Status→ Identity Upgrading Isdn BRI DBM Software Changing Software Determining Whether a Download Is CompletedMain Menu → Control→ Select Software Release If retrieving Hen Transferring Collected Data Main Menu → Control→ System Alarm Relay Cut-Off Turning Off the System Alarm Relay Operation and Maintenance September Troubleshooting Main Menu → Status → Display LEDs and Control LEDs Problem IndicatorsIndicators See Operation and Maintenance Resetting the Unit from the Control Menu Resetting the Unit and Restoring CommunicationResetting the Unit By Cycling the Power If selecting He following occurs Restoring Communication with an Improperly Configured Unit LMI Packet Capture Utility Feature Troubleshooting Management Link Feature LMI Trace Log Example LMI Packet Capture Utility→ Display LMI Trace Log Alarm Conditions 1 What It Indicates What To Do AlarmsMenu → Control → Reset Device IPAddress Alarm Conditions 2 What It Indicates What To DoMain Menu → Configuration → Isdn → Link Profiles Name Link Alarm Conditions 3 What It Indicates What To DoMenu→ Configuration→ LMI Down, frame relay DTE Alarm Conditions 4 What It Indicates What To Do PathIP Address Alarm Conditions 5 What It Indicates What To Do Nnnn , frame relay Alarm Conditions 6 What It Indicates What To Do Alarm Conditions 7 What It Indicates What To Do Viewing the Trap Event Log Troubleshooting TablesDevice Problems Device Problems 1 Symptom Possible Cause Solutions Improperly Configured Unit on Device Problems 2 Symptom Possible Cause Solutions Frame Relay PVC Problems Symptom Possible Cause Solutions Frame Relay PVC Problems Isdn DBM Problems Symptom Possible Cause Solutions Isdn DBM ProblemsMain Menu → Status → DBM Interface Status Test Menu Example Tests Available DBM Tests Test Timeout Feature Starting and Stopping a Test When the status of a test is Only command available is Aborting All Tests PVC Tests Screen Example PVC Tests Main Menu → Test→ Isdn Call/PVC Tests PVC LoopbackMain Menu → Test→ Network PVC Test Main Menu → Test→ Data Port PVC Tests Isdn Call/PVC Tests Send PatternMonitor Pattern Network PVC Tests/Data Port PVC Tests Test Call Connectivity Physical Tests Screen Example Physical Tests Main Menu → Test→ Network Physical Tests Line LoopbackLLB PLB Payload Loopback RLB AIS Repeater Loopback Dtlb DTE DTE LoopbackMain Menu → Test→ Data Port Physical Tests DSX Send Line Loopback Data Channel Loopbacks on a Frame Relay Link Main Menu → Test→ Network Physical Tests/PRI Physical Tests Send Remote Line Loopback Qrss Send and Monitor Pattern Tests Ping Screen Example IP Ping Test Target IP Address Ping Options 1 Packet Size Inter-Ping DelayPing Options 2 Source IP Address Ping Options 3 Response TimeoutPing Responses Field Possible Values Description Main Menu → Test→ IP Ping IP Ping Test Procedure Main Menu → Test→ Lamp Test Lamp Test His chapter includes OpenLane Support of FrameSaver Devices Setting Up the OpenLane SLM System Setting Up FrameSaver Support To Find Your License Key Number Ordering SLM Feature Set Activations Activation Certificate Administering and Managing SLM Activations Checking Activation Certificate Status Entering an Activation Certificate Scheduling Activations Accessing and Printing the Certificate Summary Report Canceling Scheduled ActivationsChecking the Status of Scheduled Activations 9128-A2-GB20-80 10-1 Setting Up NetScout Manager Plus for FrameSaver Devices Properties AlarmsPreparation 10-2 10-3 Configuring NetScout Manager Plus 10-4 10-5 Verifying Domains and Groups 10-6 Correcting Domains and Groups 10-7 Property Description Setting 10-8 Adding SLV Alarms Using a Template 10-9 Editing Alarms 10-10 10-11 Adding SLV Alarms Manually Field Select or Enter 10-12Paradyne 10-13 Creating History Files Change 1.3.6.1.2.1.10.32.2.1.6.@IFN.@DLCI to 10-14 10-15 Installing the User-Defined History FilesDvuhist -f Dallas51 3 config 30 60 Dallas51k.udh Dvuhist -f Dallas51 301 3 config 30 60 Dallas301.udh 10-16 Monitoring a DLCI’s History Data 10-17 10-18 Monitoring the Agent Using NetScout Manager Plus 10-19 10-20 Statistical Windows SupportedTraffic Statistics Protocol Statistics 11-1 Setting Up Network Health for FrameSaver Devices 11-2 Installation and Setup of Network Health 11-3 Discovering FrameSaver Elements 11-4 Configuring the Discovered Elements 11-5 Grouping Elements for Reports 11-6 About Service Level ReportsGenerating Reports for a Group About At-a-Glance Reports 11-7 Reports Applicable to SLV DevicesAbout Trend Reports Printed Reports 11-8 FrameSaver SLV Plus At-a-Glance Report 11-9 11-10 Menus Menu Hierarchy Status Easy Install Menu Hierarchy September Snmp MIBs and Traps, and Rmon Alarm Defaults Downloading MIBs and Snmp Traps MIB Support FrameSaver Unit’s sysObjectID system System Group mib-2Interfaces Group mib-2 FrameSaver Unit’s sysDescr system Frame Relay Logical Layer Profile Link Name NAM NetScout Indexes to the Interface Table ifTable FR Service T1 FR NAMFR DTE T1 FR NAM Number Dlci number DTE Rmon Logical LayerIfName of the interface Number Dlci number ALL Examples Standards Compliance for Snmp Traps Variable-Binding Trap authenticationFailureTrap warmStart Table B-3. warmStart Trap What It Indicates Possible Cause Traps linkUp and linkDown Strings Physical SublayerPRI MIB Logical Link Sublayer BRI Xxx.xxx.xxx.xxx , COS nn Traps enterprise-Specific ‘Path xxx.xxx.xxx.xxx Up Nnnn ’ That the secondary clock source Traps RMON-Specific Standard Dial Control MIB Trap dialControl Dial Control Extension MIB Rmon Alarm and Event DefaultsEvent Defaults EventIndex EventDescription EventType EventCommunity Rising Event Operation Physical Interface Alarm Defaults Frame Relay Link Alarm Defaults Snmp MIBs and Traps, and Rmon Alarm Defaults MIB FR DTE MIB RFC Dlci Alarm Defaults Paradyne Area Dlci Alarm Defaults NetScout Area OID Rx Dlci Link Object ID Cross-References Numeric Order MIB Rmon II RFC 6.1.2.1.2.2.16.1.2.1.2.10.32.2.1 6.1.2.1.16.12.2.1 CIR 6.1.4.1.1795.2.24.26.1.4.1.1795.2.24.2.6.9.4 Dlci CIR Dlci EIR 6.1.4.1.1795.2.24.2.6.9.4.5.2.1 6.1.4.1.1795.2.24.2.6.9.4.4.26.1.4.1.1795.2.24.2.6.9.4.7.1 6.1.4.1.1795.2.24.2.6.9.4.10.3.1 6.1.2.1.10.32.2.1 6.1.2.1.10.18.9.1 6.1.4.1.1795.2.24.2.6.9.4 6.1.4.1.1795.2.24.2.6.9.4 Xxxxxxxxxxxx CLI CommandsConvention Meaning X.x Router CLI Commands, Codes, and Designations Table C-2. Access Control Commands Pager CommandAccess Control Commands Table C-1. Pager Command Example configure terminal Configuration CommandsTable C-3. Configuration Commands Configure terminal factory Example interface serial 132.53.4.2 Interface CommandsTable C-4. Interface Commands 1 Command Mode config, config-if, config-subif Example encapsulation frame-relay ietf Table C-4. Interface Commands 2Encapsulation encapsulation-type encapsulation-protocol Example ip address 132.53.4.2 Example ip unnumbered Table C-4. Interface Commands 3No ip unnumbered null No frame-relay interface-dlci dlci-num No ip multicast-routing IP Routing CommandsTable C-5. IP Routing Commands No ip routing Table C-6. Bridge Commands 1 Bridge CommandsExample bridge crb 1 route ip Example no bridge-group Table C-6. Bridge Commands 2Command Mode config-if, config-subif No bridge-group bridge-group Example arp timeout ARP CommandsTable C-7. ARP Commands Arp timeout time No arp timeout time No ip nat inside outside NAT CommandsTable C-8. NAT Commands 1 Example ip nat translation timeout No ip nat pool pool-namestart-ip-addr end-ip-addr Table C-8. NAT Commands 2Ip nat pool pool-name start-ip-addr end-ip-addr Netmask netmask prefix-length / prefix-length Clear ip nat translation Table C-8. NAT Commands 3From previous No ip dhcp pool pool-name Dhcp Server CommandsTable C-9. Dhcp Server Commands 1 No service dhcp Dns-server ip-address No dns-server ip-address Table C-9. Dhcp Server Commands 2Default-router ip-address No default-router ip-address Domain-name domain-name No domain-name domain-name Network network-num Table C-9. Dhcp Server Commands 3 Example ip dhcp relay max-clients Dhcp Relay Agent CommandsTable C-10. Dhcp Relay Agent Commands No ip dhcp-server ip-address No access-list access-list-numpermit deny Filter access-list CommandsTable C-11. Filter Commands 1 Access-list access-list-num permit deny For Extended IP Access Lists Table C-11. Filter Commands 2 For Protocol Type Access Lists Table C-11. Filter Commands 3Example access-list 200 permit 0x200 range No ip access-group access-list-1-199numin out Table C-11. Filter Commands 4 Table C-12. Diagnostic Commands 1 Diagnostic Commands Traceroute protocol dest-ipsource source-ip length bytes Table C-12. Diagnostic Commands 2 Show arp Show CommandsTable C-13. Show Commands 1 Show configuration Show interface intf-type intf-num .sub-intf-num Table C-13. Show Commands 2Show configuration saved unsaved Show frame-relay map Show ip route ip-address Table C-13. Show Commands 3Show ip dhcp binding ip-address Show ip nat translations Show ip traffic Table C-13. Show Commands 4Show spanning-tree Table C-14. Ethernet Type Codes Hex 1 Description Ethernet Type Codes Table C-14. Ethernet Type Codes Hex 2 Description Icmp Designations Protocol and Port DesignationsAll 3 n = Destination unreachable All 5 n = All redirects TCP Port Designations UDP Port Designations CLI Summaries Router Command Line Summaries Shortcuts Table D-1. Show Commands Function Show Command SummaryIntf-type intf-num .sub-intf-num Table D-2. Access Control and System Level Commands Function Access Control and System Level Command Summary Dns-serverip-address CLI Command SummaryTable D-3. CLI Commands 1 Clear counters intf-type intf-num .sub-intf-num Encapsulation encapsulation-type encapsulation-protocol Table D-3. CLI Commands 2 CLI Command Default Settings Rear Panels Connectors, Cables, and Pin Assignments Connectors, Cables, and Pin Assignments Model COM Port for 9126 and 9128-II 25-Position COM Port ConnectorSignal Direction Pin # Pin # Signal Direction Modular Plug DB9 Socket COM Port-to-PC Cable Feature No -F2-550COM Port for 9128-II Carrier Mount COM Port Non-Keyed Position COM Port Non-Keyed COM Port-to-Terminal/Printer Cable Feature No -F2-540Position Modular Plug DB25 Plug Cisco 2500 Series Router RJ45 Jack COM Port AUX Port Signal DB25 Pin # Direction RJ45 Pin #COM Port AUX Port Signal DB25 Pin # Direction COM Port-to-Router Cables COM Port AUX Port Signal RJ45 Pin # Direction COM Port Console Port Signal DB25 Pin # Direction DB9 Pin #3COM Router DB9 Socket COM Port AUX Port Signal RJ45 Pin # Direction DB25 Pin # DTR RTS Gender Adapter/ChangerLAN Adapter Converter and Cable Plug-to-Modular Jack Converter Com Port Position DB25 Plug Direction Pin Socket DTE Port Connector Pin Standard V.35 Straight-through CableStandard V.35 Crossover Cable MM NN Position DB15 Modular Plug Socket Unkeyed DSX-1 ConnectorDSX-1 Adapter Feature No -F1-560 Function Circuit Direction Pin Number DSX-1 Port for 1-Slot 9128-II 15-Position T1 Mass Termination Cable Feature No -F1-500 T1 Network Cable Feature No -F1-500Function Circuit Line # Pin # Canadian T1 Line Interface Cable Feature No -F1-510 Ethernet Port ConnectorPlug Unkeyed Isdn DBM Connector Modem ConnectorIsdn Modular Cable Connectors, Cables, and Pin Assignments September Physical Environment Table F-1. NAM Technical Specifications 1 CriteriaPhysical Dimensions Approvals Table F-1. NAM Technical Specifications 2 Criteria Ethernet Port Table F-1. NAM Technical Specifications 3 CriteriaIsdn PRI DBM Interface B8ZS Power Consumption Dissipation BRI, NI-1 Isdn BRI DBM InterfaceEthernet Port FrameSaver Typical Power Consumption AC Power RequirementsHeat Dissipation Max Standards Compliance Switch CompatibilityService Supported Switched Network Interface Coding Format Framing FormatLine Build-Out LBO FrameSaver SLV Units Model/FeatureEquipment Description Number Equipment List Isdn PRI DBM NMS Products FrameSaver SLM Feature Set UpgradeOptional Features Power Supplies Series Access Carrier 9128-II NAM only Cables Description Part Number Feature Number IN-1 Index Becn IN-2CLI Dhcp IN-3 DBM IN-4 EER IN-5EIR IN-6 LAN IN-7IP SLV LOF IN-8LOS NMS IN-9 OID IN-10 Port IN-11 IN-12 IN-13 IN-14 IN-15 IN-16

Paradyne CSU, DSU, 9126-II, 9128-II Upgrading System Software, If the message displayed is Then

Models: CSU, DSU 9126 9126-II 9128-II

7. Operation and Maintenance

Upgrading System Software

Procedure

If the message displayed is . . .

Then . . .