116 | Printronix P7000 instruction

Chapter 4 NETWORK SETUP MENU

ASCII Data Port

This option sets the port number for ASCII print jobs. The data port number needs to match your host system setting.

•9100 (default)

•1023 - 65535

IPDS Data Port

This option allows you to set the port number for IPDS print jobs only if the IPDS option is installed.

The range is 1023 - 65535, and the factory default is 5001.

Keep Alive Timer

This is the time that the Keep Alive Timer will run. With the Keep Alive Timer on, the tcp connection will stay connected even after the print job has terminated.

•3 Minutes (default)

•2 - 10 Minutes

Ethernet Speed

This menu option only appears if a 10/100Base-T network interface card (NIC) is installed. The Ethernet Speed menu allows compatibility with different systems and networks. The factory default is Auto Select.

•Auto Select. (default) This setting tells the 10/100Base-T NIC to perform an auto detection scheme and configure itself to be 10 Half Duplex, 10 Full Duplex, 100 Half Duplex, or 100 Full Duplex.

•10 Half Duplex. Tells the 10/100Base-T NIC to communicate at 10 Megabits per second using half duplex.

•10 Full Duplex. Tells the 10/100Base-T NIC to communicate at 10 Megabits per second using full duplex.

116

Image 116

Printronix P7000 user manual 116

Contents

P7000 User’s Manual Software License Agreement User’s Manual Trademark Acknowledgements Copyright 1997, 2005 PRINTRONIX, INCPage Trademark Acknowledgements Table of Contents Configuration Menus Wlan Kerberos Wlan Leap Advanced User DiagnosticsPrinter Control 353 Table of Contents Printer Overview P7000 Series PSA3 Printer Stacker Printer OverviewPrintronix P7000 Printers Integrated Print Management System Integrated Print Management SystemOutput Darkness Ribbon Log Ribbon FlippingLoading a Used Ribbon Graphics Enhancements Taking Care Of Your PrinterConsumable Monitoring With PrintNet Enterprise Graphics Enhancements LCD Conventions In This ManualConventions In This Manual Related Documents Related Documents Printronix Customer Support Center Americas Europe, Middle East, and Africa Asia Pacific Power Requirements Before You Begin Select a Site Select a Site Printer Dimensions Printer Dimensions Printer Dimensions Cabinet Model with Paper Stacker Printer Dimensions Pedestal Model Printer Component Locations Printer Component Locations Powering On The Printer Operating Modes Online PGL Ribbon Life = 100% Control PanelControl Panel Control Panel Keys Control Panel Keys Cancel UP or Down = or UP + Down = + Control Panel Prev or Next or Prev + Next += + on Line Ipds Emulation only = + Paper Advance Ipds Emulation only Ribbon Life Indicator Control Panel Keys = + View Ipds Emulation only Operational Procedures Operational ProceduresReload Paper Cabinet Models Pedestal Models Reload Paper Loading New Paper into the Printer Setting the Platen Lever Paper Slots on the Printers Loading Paper on the Left Tractor Positioning the Left Tractor to Avoid Damage Loading Paper onto the Sprockets Cabinet Model Cabinet models Aligning the Perforation with the TOF Indicator Adjusting the Platen Lever Unload Paper Unload Paper Removing Stacked Paper from the Printer Completely Removing the Paper Integrated Print Management System Lighter Or Darker Print Changing Ribbons Changing Ribbons Loading the Barcoded Ribbon Threading the Ribbon Around the Ribbon Guide Cancel a Print Job Configuration Menus Configuration Overview Configuration Overview Changing Parameter SettingsSaving Parameter Settings Default And Custom Configurations Default And Custom Configurations Navigating The Menus On LINE/CLEAR Enter @ BOF Changing Parameters ExampleChanging Parameters Example Step Press LCD Enter Switch Locked Auto Save Configuration On LINE/CLEAR17A.ENTER Online Saving Your New Configuration Saving Your New Configuration Configuration Overview Example Enter Offline CONFIG. Control Enter Switch Locked On LINE/CLEAR Online Saving Your New Configuration Example Offline CONFIG. Control Enter Switch Unlocked Quick Setup Chapter Until TES Until Test Optimizing Print Quality LP+, IGP/PGL, and IGP/VGL Emulations Optimizing Print Speed Optimizing Print Speed Main Menu PGL SfccIGP/PGL IGP/VGL Main Menu Ipds LG 1 PCL-II Main Menu Ipds Dhcp WlanDhcp Emul IGP/PGL* IGP/VGL PGL Sfcc VGL Sfcc Quick Setup Sfcc Adapter Address Host InterfaceDevice ID Ethernet Address Wlan Address Active IGP Emulation Printer ProtocolForm Length Form Width Select CPI Select LPISeries Sfcc Margins Vert Forms Horiz Forms Length RepMax Line Width Ribbon End Point Save Config Power Up Config Load Config CONFIG. Control Print Config Delete ConfigPower-Up Config Protect Configs Name Configs Reset Cfg Names Host Interface Host Interface Auto Switching SubmenuAuto Switching Auto Switching Auto Switching SubmenuPort Type Trickle Time Timeout Ieee 1284 Parallel Bidirectional SubmenuReport Status Ieee Prime Signal TOF ActionBuffer Size in K Auto Trickle Offline Process Centronics Parallel Submenu Data BitCentronics Parallel Submenu Centronics PI Ignored Data PolarityResp. Polarity Busy On Strobe Prime Signal Dataproducts Standard Submenu Dataproducts Dataproducts Standard Submenu Prime Signal Dataproducts Standard Submenu Serial Submenu Serial Serial Submenu Interface TypeData Protocol 100 Series1 1 Char Response Characters Printer State Series1 2 Char Response Characters Printer State Baud Rate Word LengthStop Bits Parity Data Term Ready Request To Send Idle Response Poll CharacterPoll Response Framing Errors One Char Enquiry Net Adapter Submenu Net Adapter Ethernet Ethernet SubmenuEthernet Submenu Network Setup Menu IP Address Subnet MaskGateway Address MAC Address Ascii EnableNDS NetBIOS Protocol Auto Sensing default Ethernet SnapNovell Protocol Nest Serv Type Keep Alive Timer Ascii Data PortIpds Data Port Ethernet Speed Job Control Ethernet Address 114 Ethernet Params 116 Wlan Address 118 Wlan Params 120 Wlan Kerberos Kerberos Reset Kerberos Password Wlan Leap Reset Leap User Active IGP Emul IGP/PGL IGP/VGL IGP/PGL Emulation FeaturesIGP/PGL Emulation IGP/PGL Emulation Configuring The Emulation With Control Panel IGP/PGL Submenu IGP/PGL SubmenuCPI MVP 130 UPC IGP/PGL Submenu with PCL-IIIGP/PGL Submenu with PCL-II IGP/PGL Submenu with LG Autowrap Define CR Carriage Return CodeDefine LF Line Feed Code PI Slew Range CR EditSelect Font Slash Auto Uppercase Skip Cmd PrefixForms Handling 10.0 Power On IGP/PGL Ext Execute CopyBarcode Options X2 DPD Optimized Ratio Barcode OptionsUPC Descenders Select SO Char IGP/PGL Emulation 5 SelectionAI 00 Spaces IGP/PGL Submenu User-Def Ratio Var Form AdjustHost Form Length Ignore Mode Var Form TypeCompressed CPI Ignore Char Expanded Font L150 P3000 P6000 P9000 Scalable Size True Form SlewPrinter PI Line Pmode Trunc Dyn Data Power-on S-ModePrint Quality Error Report IGP/PGL Font Set Menu Select FontMS DOS CP710 MS DOS CP720 CP 858 Euro IGP/VGL Emulation IGP/VGL Emulation Configuring The Emulation With The Control Panel IGP/VGL Submenu IGP/VGL SfccVGL Sfcc 5E LPI IGP/VGL Submenu Graphics Options IGP/VGL Submenu with PCL-II ISO IGP/VGL Submenu with PCL-II IGP/VGL Submenu with LG 153 Power Up Power Up FPower Up PY Sfcc & Pwrup Graphics Options Rot. Char Size IGP/VGL Emulation True Vert 1/10Absorb After PY IGP/VGL Submenu Ignore Spaces Midline PY includes PNPrint Quality Expanded Font LP+ Font IGP/VGL Emulation MSI Check Digit I25 Selection Height Param Max. Width IGP/VGL Submenu Width LimitWidth Limit Table IGP/VGL Emulation Absorb After PN IGP110 CompatblAuto FF at PN Ignore Lxx Cmd Error Handling Error MsgsError Markers Offpage Errors Ignore / DB8 Setup Ignore CharsIgnore CH#1 Ignore CH#2 Font Set PI ControlIGP/VGL Submenu Data Bit Printer PI Max PI Prt To EmulateIGP/VGL Emulation Host PI IGP/VGL Font Set Menu Font Set CTHI1 ANSI1 IGP/PGL1 IGP/VGL1 IPDS1 PCL-II Coax/Twinax Cthi Emulation Coax/Twinax Cthi EmulationStandard Simple Prot Conv Coax Emulation Coax EmulationPA1 PA2 IGP/DCU Char Set Select OCR aOCR B Compatibility Char Set Select Translation TblActive Char Set Prt Partial Line Buffer Reprint Early Print Cmpl Cancel IGP/DCU SCS Buffer CntrlPTX Transparent Lead-in Chars Change Case Set Text OrientnCoax/Twinax Cthi Emulation Usr Defined Htrn Start Code 1 5F Start Code 2 5F Stop Code 5B Alt. Set 80-9F Image Buf Size Intervention ReqCompatibility Op CR At MPP+1 Coax/Twinax Cthi Emulation Position Aft FF 4234 only Last Char = FFNull Suppression FF Validity CR, EM, and NL 3287 only Coax Emulation Auto Skip At EndFF After Job Format Control Translate TableHost Override Max. Print Width Buffer Print Twinax Params LAC Twinax Params Device Address World Trade User Defined Usr Defined Htrn LAC Option Graphic Chek ErrGraphic Chek Cod Control By Host default Left to Right Right to Left LAC Approx 186 3270 Params ParamsParams 188 Primary Sets default Secondary Sets 190 Not Send To Host Dual Case default Mono CaseLeft to Right default 192 Params Last Char = FF Coax/Twinax Cthi Emulation Auto Skip At End Inches default 5250 Params 1144 Euro Ital 0893 Secondary Set default Primary Set Params Usr Defined Htrn 40 F4 Printer Width the maximum width of the printer 201 SPC Coax Params Logical Buf SizeHtrn SPC Column 132 Wrap Usr Defined HtrnSPC Coax Params Start Code 1 5F Start Code 2 5F Stop Code 5B SPC Null Supp Online SPC Space Supp NL At MPP+1 Mode IBM SPC Twx ParamsMode IGP/VGL IGP/PGL SPC Type Evfu SPC Char Set CPI/LPI LinePrinter Plus EmulationLinePrinter Plus Emulation Printer Protocol Font AttributesOCR-A OCR-B Barcode Format LinePrinter Plus Emulation with PCL-II LinePrinter Plus Emulation with PCL-II NLQ OCR-A OCR-B Host CommandCPI/LPI Select Font Attributes Typeface Prop. Spacing Proportional Spacing LinePrinter Plus Emulation with PCL-II Bold Print Italic PrintSlashed Zero Text Position Format Print Char. Set Barcode X-Offset Reset Cmd CFG LdSet Substitution Series Emulation Series EmulationSeries LF = LF Series Emulation with PCL-II Elongated default Backspace Series Emulation with LGControl Code Series Emulation with LG Define CR Code Auto LFOverstrike Define LF Code Alt. Set 80-9F Control Code default PrintableVFU Select Sfcc d Command Character SetPSeries Dbl High FF Valid at TOF Series Character Set Menu Character Set Series Character Set Menu with PCL-II Ascii USA From = Factory Default Series Character Set Menu with LG Series XQ Emulation ETX Series XQ Emulation HS Print High Speed Print Compressed PrintElong/Alt. Font Slew Relative Lines defaultUpr. Case Select Serial Matrix Emulation Serial Matrix Serial Matrix Emulation ESC d command Printer Select = Factory Default Arabic Sets Serial Matrix Character Set Menu Proprinter XL Emulation Proprinter Proprinter XL Emulation Alt. Char Set CPI Condensed Proprinter XL Character Set Menu Proprinter XL Character Set Menu with PCL-II Proprinter XL Character Set Menu with LG Epson FX Epson FX EmulationEpson FX Emulation 242 Character Set Epson FX Character Set Menu 245 Epson FX Character Set Menu with PCL-II Epson FX Character Set Menu with LG Ansi Emulation Ansi Emulation Character Set from Format USA Choose a typeface from the available options Ansi Emulation Slashed Zero Characters Define CR Code ESC c Sequence Private Mode Received CRReceived DEL Pos. on BC/OvrSz PUM Default Barcode DarkmodeTruncate PI Slew Immediate Afterprint Ipds Emulation Ipds Emulation Ocra Ocrb PSM Ipds EmulationDraft Barcode Quality Font SizeGraphics Quality Early Print Comp Complete Barcode SpeedBarcode Size Default Code Pag Graphics ScalingGraphic CharSize 5 Checksum Default Font Hexdump ModeCode Page Subset VPA Check PCL II Emulation PCL-II Emulation Secondary Char. Set PCL II EmulationPrimary Primary Char. Set Second Char. Set Face CPI Delay Graphics Density Perforation SkipDisplay Functions Line Terminator L./Lines LPI AdjustPTX Linefeed L./Inches Config PrintSymbol Set Print LG Emulation LG Emulation 270 Font 272 LG Emulation Print Mode Opt Unsolicited Rpt Plot Mode Opt 5 Guard Bars Printer Control @BOF Eject Function Darker +1 through Darker +6 Lighter -1 through Lighter Open Platen @ BOF Bottom of Form Unidirectional Bar Code QualityTear Bar Dist. Distance Display Language Accented Char Advanced User Advanced User PTX Setup OptionHex Dump Mode Downloaded Fonts Power-Up StatePMD Paper Motion Detection Fault Auto Locking Power StackerAuto Elevator File System Set Sharing Slow Paper Slew Shuttle TimeoutAlarm Pwr Save Control Power Saver TimeCancel Key Set Lock Key Ribbon Action Dram Ink Saver ModeTest Width Diagnostics Printer Tests Paper Out Dots System Memory Flash Avail Print StatisticsDram Avail Optional Host Interfaces OverviewStandard Host Interfaces Dataproducts Parallel Interface Dataproducts Parallel Interface Dataproducts Parallel Interface Signals Dataproducts Parallel Interface Signals Centronics Parallel Interface Centronics Parallel Interface Centronics Parallel Interface Signals Centronics Parallel Interface Signals Compatibility Mode Nibble ModeByte Mode Ieee 1284 Parallel Interface Signals SignalsPage Signals Terminating Resistor Configurations Resistor Locations Removal And Installation Terminating Resistor Configurations RS-232 And RS-422 Serial Interfaces RS-232 And RS-422 Serial Interfaces RS-232 RS-232 RS-422 How To Program The Security Key Reprogramming The Security Key Reprogramming The Security Key NEW SPX Detected Press EnterPROGRAMMING. Please Wait Remove Used SPX then Press Enter How To Program The Security Key 310 Cleaning Requirements Exterior Cleaning Interior Cleaning Cleaning Requirements Interior Cleaning Bar Code Verification Diagnosing ProblemsDiagnosing Problems Printing a Hex Dump Printing a Hex Dump Fault Messages Fault Messages Requiring Field Service Attention Timeout Host RequestHold Print 5V PWR Fail Access Null Paper JAMPlaten Open Ribbon Stall Fault Messages Displayed Message Can User Explanation Solution Correct? B19 Error DC Download ModePrinter Reset B22 Error B23 Error B40 Error Sdram DimmB41 Error DIM B42 Error B43 Error B44 ErrorB45 Error B46 Error B49 Error B50 ErrorB51 Error SDA Sdram # Logical Barcode DamagedBuffer Overrun Clear Paper JAM Diagnostic Do not PowerClearing Program from Error DC Error Dram ATError EC NET Test Error Flash did Error FlashError Locked Error no Dram Error Error ProgramError Security Error Short AT Error Writing Error WrongTo Flash Checksum Framing Error Exhaust FAN FLTFirmware FM Header GRF CHK Error HB not InstalldFreeform OFF Freeform on Intake FAN Fault HMR Bank FANFLT ILL EXT BUS ACC Invalid Command InterruptUnused Vector Invalid Activate Program Into NEW SPXPress Enter NON Volatile CU Timed OUT PAP BAD TablePAP BSY TOO LNG PAP Fifo Overfl Parity Error PAP not SchedPAP NT AT Speed PAP Unexp INT Reset Power SaverPower Supply Please Wait Restoring Boot ProtectedInstr PWR Supp Volt SCS Command RIB Invld StateRibbon Drive Ribbon Under 2% Security KEY SendingTo EC Processor Cycle Power EnabledShuttle Stall Software Stacker Fault Stacker FullStacker JAM Table Mismatch Undef UndfnedOpcode Unknown RBN1 344 Specialty Ribbons Ribbon SpecificationsStandard Ribbons Part Number Paper Specifications Appendix a Paper Specifications Paper Specifications Labels Printer Weight And Dimensions Environmental Characteristics Electrical Characteristics Acoustic Noise LevelEnergy Star Acoustic Noise Levels Cabinet Models Pedestal Per ISO Electrical Characteristics Interfaces Printing Rates Appendix a Printing Rates Ascii Character Set Appendix B Communication Appendix C Notices Page Energy Star Product Recycling and Disposal Appendix C Communication Statements Communication StatementsFederal Communications Commission FCC Statement European Union EU Conformity Statement Industry Canada Compliance Statement Handbuchtexte FCC class a entspricht Emvg Klasse a China Declaration Taiwan Lithium Battery Warning Korea Software License Agreement Appendix C Software License AgreementObject Code License Source Code No Warranty Conflicting Terms S. Government Users Red Hat Statement with regards to eCos Software 370 Index Index B30 Status Initializing B35 Waiting for EC Status B47 Error Sdram Larger than Index Cancel PRT ConfigClear JOB Select Index Dhcp Error Security KEY not Ethernet Adapter Being Host Request Hold Print Timeout B23 Error Decompress Barcode Missing B40 Error Sdramee Prom Close PlatenB41 Error DIM Memory not CTL Volt Fail Diagnostic Passed Error Program Needs More ILL EXT BUS ACC Error Program Needs More Incompat E-NETError Program not Interrupt Unused Compatible Error Short AT Address Load Paper Power Index Index PGL Sfcc Index Index Menu Index Index Index Index Horiz Forms Host Interface Margins Max Line Width Length Rep Index VGL Sfcc Index Index Index 400 Page 178660-001