Toshiba dk14, DK40I, DK424I manual Programming for ISDN PRI LDN Type Call, Isdn

			ISDN
		Guidelines for Programming ISDN Calling Features
Table 7-3 ISDN PRI DNIS Type Call Programming (continued)
Program	Program Data	Description
Number
71-1	000 XXXX	This tells the system to route the incoming DNIS call that was route to DNIS
		address 000 to Station Port XXXX.

Programming for ISDN PRI LDN Type Call

The following table shows the minimum programming needed to make Listed Directory Number (LDN)-type ISDN PRI calls work in the Strata DK System.

Table 7-4 ISDN PRI LDN Type Call Programming
Program	Program Data	Description
Number
03	XX 79	“XX” is the DK slot where the RPTU PCB is placed.	ISDN
10-4	LED 9 On	LDN registration will route the unknown number or call type in numbering
		plan.
*16	XX 2	This tells the system that trunk group XX is an ISDN PRI Trunk Group.
		This tells the system to make the ISDN PRI Span the Primary Clocking
*42	1 XX 1	Source for the DK System. XX equals the slot in the DK system where the
		RPTU PCB is placed, and to look at circuit (1).
*43-1	1 24	This tells the system that the D-Channel on the 1st ISDN PRI Span is the
		24th channel on the PRI Span.
*63-2	04	This tells the system how long to wait to collect digits from station users
		making a ISDN PRI Call before sending it to the network.
*64	1 LED 01 Off	This tells the system to except the incoming calls on the PRI Span as LDN
		type calls.
*65	1 CO LEDs 001-023	This tells the system that there are 23 bearer channels on the first Channel
	On	Group, and that they will appear on CO lines 001~023.
*66-1	01 1	This tells the system that Trunk Group 01 is assigned to PRI Channel Group
		1.
	01 LEDs 01-02, 11-12	This tells the system that Operator Calls, Carrier Access, 1+10 Digit Dialing,
	On	and Ring Back Tone to the outside caller are allowed.
	01 LED 13 On	This tells the system when interfaced with DMS XXX to send the progress
*66-3		descriptor 81 or 83.
	LED 14 On	When connecting to a DMS XXX with NI1 protocol.
	LED 15 On	Set up message for outgoing call. When connecting to a DMS XXX. LED 11
		must be Off in Program *66-3 when this LED is On.
*66-5	1 01 XXX-XXXX	XXX-XXXX tells the system what the LDN number is that the network will be
		sending for the LDN Type Call for Trunk Group 01.
	1 01 CO LEDs	This tells the system to ring CO appearances 001~023 for incoming LDN
*66-6		calls that match the LDN number that was entered in Program *66-5 for that
	001~023 On
		Trunk Group.
*67-1	01 3	This tells the system that the PRI Span is for both-way calling.
*67-2	01 LEDs 01~04 On	This tells the system to accept Speech, 3.1K Analog, 56K, and 64K type calls
		on the ISDN PRI Span.
*68-1	01 LEDs 011~03 On	This tells the system to accept and send Calling Party Number on ISDN PRI
		Calls.
*68-2	01 XXX-XXX-XXXX	XXX-XXX-XXXX is the number you want the system to send out on an
		outbound call for Caller Number Identification.

Strata DK Programming 5/00 7-9