Toshiba MMU-AP0091H service manual Timer Operation, Timer operation, Cancel of timer operation

Floor Standing Type

Adjustment of air Flow direction upwards/downwards

[In Cooling operation]

In cooling operation, move the louver with your hands so that the horizontal air outlet points in a direction so that the cold air diffuses the entire room.

[In Heating operation]

In heating operation, move the louver with your hands so that the horizon- tal air outlet points in a downward direction, towards the floor.

Adjustment of air Flow direction rightwards/leftwards

[In case of using unsymmetrical air directions]

Lift up the vertical louver lightly and direct it towards the desired 2 direction once completed lower the louver back down.

In this case, do not use the Swing function. 1

3-10. Timer Operation

The type of timer operation can be selected from the following three types.

OFF timer	: The operation stops when the time on the timer has reached the set time.
Repeat OFF timer	: The unit will stop, every time the set time period has elapsed.
ON timer	: The unit will start when the time on the timer has reached the set time.
Timer operation
		TEMP.		ON / OFF
	1	TIMER SET	FAN	MODE
		TIME	SWING/FIX	VENT
		FILTER		2
		RESET TEST SET CL	UNIT

[In case of automatic swing]

1 Push the SWING/FIX button during operation.

• [SWING	] is displayed and the air direc-
tion will automatically change rightwards/
leftwards.
In cases where one remote controller
controls multiple indoor units, it is possible to

In this case, do not use the swing function.

TEMP. ON / OFF

3 4

42

set each indoor unit individually, so that the

air flow direction can be altered.

2 Push the SWING/FIX button again whilst the vertical louver is moving will allow you to stop the louver in the desired posi- tion.

3 Swing button UNIT

• To set up the air flow the direction individu- ally, push the UNIT button to display each

	TIMER SET
	TIME
FILTER
RESET TEST	SET CL

1, 2

FAN MODE

SWING/FIX VENT

UNIT

3

1	Push the TIMER SET button.
					OFF			OFF		ON
	• The timer display (type) changes for every
	push of the button.			(OFF timer)		(Repeat OFF timer)			(ON timer)
	• SET TIME and timer time displays flash.						No display
2	Push the	TIME	buttons to select the “SET TIME”.

For every push of the button, the set time increases in the unit of 0.5 hr (30 minutes). The maximum set time is 72.0 hr.

For every push of the button, the set time decreases in the unit of 0.5 hr (30 minutes). The minimum set time is 0.5 hr.

indoor unit No. in a group control. Then set up the air flow direction to the desired indoor unit.

•If there is no display, all the indoor units can be operated collectively.

• Every push of the UNIT button, will change the display as shown in the figure.

No display Unit No. 1-1 Unit No. 1-2

Unit No. 1-4 Unit No. 1-3

3 Push the SET button.

•The SETTING display disappears and the timer time display goes on.

(When the ON timer is activated, the chosen time period will be displayed. Once the time has been reached, all displays except the ON light will disappear.)

Cancel of timer operation

4 Push the CL button.

INFORMATION

•If cooling operation is performed with downward air outlet, dew may form on the surface of the cabinet or the horizontal louver, resulting in possible dripping of water.

•If heating operation is performed with the horizontal air outlet actively moving, unevenness of the tem- perature may increase within the room.

•Do not move the louver directly with your hands during swing operation; otherwise a fault may be caused. The vertical louver does not stop immediately even if the SWING/FIX button is pushed.

To adjust the stop position, push the SWING/FIX button.

• TIMER display will disappear.

NOTICE

• When the unit stops after the timer has reached the preset time, the Repeat OFF timer will resume the operation. However by pushing the ON / OFF button the repeat function will stop once the time on the timer has again reached its set time.