Toshiba MMU-AP0091H service manual Description At shipment, HEAT, Heat → Cool

Table: Function selecting item code (DN)

(Items necessary to perform the applied control at the local site are described.)

DN	Item			Description				At shipment
01	Filter display delay	0000	: None		0001	: 150H	According to type
	timer	0002	: 2500H		0003	: 5000H
		0004	: 10000H
02	Dirty state of filter	0000	: Standard				0000	: Standard
		0001	: High degree of dirt (Half of standard time)
03	Central control	0001	: No.1 unit	to	0064	: No.64 unit	0099	: Unfixed
	address	0099	: Unfixed
04	Specific indoor unit	0000	: No priority		0001	: Priority	0000	: No priority
	priority
06	Heating temp shift	0000	: No shift		0001	: +1°C	0002	: +2°C
		0002	: +2°C	to	0010	: +10°C	(Floor type 0000: 0°C)
						(Up to +6 recommended)
0d	Existence of [AUTO]	0000	: Provided				0001	: Not provided
	mode	0001	: Not provided (Automatic selection from connected outdoor unit)
0E	Follows operation	0000	: Does not follow				0000	: Not provided
	mode of the header	0001	: Follows
	unit
0F	Cooling only	0000	: Heat pump				0000	: Heat pump
		0001	: Cooling only (No display of [AUTO] [HEAT])
10	Type	0000	: (1-way air discharge cassette)				According to model type
		0001	: (4-way air discharge cassette) to 0037
11	Indoor unit capacity	0000	: Unfixed		0001 to 0034		According to capacity type
12	Line address	0001	: No.1 unit	to	0030	: No.30 unit	0099	: Unfixed
13	Indoor unit address	0001	: No.1 unit	to	0064	: No.64 unit	0099	: Unfixed
14	Group address	0000	: Individual		0001 : Header unit of group		0099	: Unfixed
		0002	: Follower unit of group
19	Louver type	0000	: Not provided		0001	: Swing only	According to type
	(Adjustment of air	0004	: [4-way Air Discharge Cassette type] and [Under Ceiling type]
	direction)
1E	Temp difference of	0000	: 0 deg	to	0010	: 10 deg	0003	: 3 deg
	[AUTO] mode	(For setup temperature, reversal of COOL/HEAT by ± (Data value)/2)						(Ts±1.5)
	selection COOL →
	HEAT, HEAT → COOL
28	Automatic restart of	0000	: None		0001	: Restart	0000	: None
	power failure
29	Operation condition	0000	: Usual		0001	: Condition ignored	0000	: Usual
	of humidifier	(Detection control for heat exchanger temperature)
2A	Selection of option/	0000	: Filter input		0001	: Alarm input (Air washer, etc.)	0002	: None
	error input (CN70)	0002	: None
2E	HA terminal (CN61)	0000	: Usual		0001	: Leaving-ON prevention control	0000	: Usual
	select							(HA terminal)
30	Automatic elevating	0000	: Unavailable		0001	: Available	0000	: Unavailable
	grille
31	Ventilating fan	0000	: Unavailable		0001	: Available	0000	: Unavailable
	control
32	TA sensor selection	0000	: Body TA sensor		0001	: Remote controller sensor	0000	: Body TA sensor
33	Temperature unit	0000	: °C (at factory shipment)				0000	: °C
	select	0001	: °F
40	Drain pump control	0000	: None		0001	: Pump ON	0003	: Pump OFF
		0002	: None		0003	: Pump OFF
5d	High ceiling selection	[4-way Air Discharge Cassette type] and [Under Ceiling type]					0000	: Standard
	(Air volume selection)	0000	: Standard filter		0001	: Super-long life filter
		0003	: High efficiency filter
		[Concealed Duct Standard type]
		0000	: Standard static pressure (40Pa)
		0001	: High static pressure 1 (70Pa)
		0003	: High static pressure 2 (100Pa)
		0005	: Correspond to quiet sound
		0006	: Low static pressure (20Pa)
60	Timer set	0000	: Available (Operable)				0000	: Available
	(Wired remote	0001	: Unavailable (Operation prohibited)
	controller)
62	Anti-ceiling	0000	: Clear				4- way Air Discharge
	smudging control						Cassette type only

72