Sharp MX-FX13 appendix 101, OWN Passcode SET, Speaker Volume, TX/RX END Sound Length

SYSTEM SETTINGS

OWN PASSCODE SET

Use this setting to program the fax number of the machine and the name of the user. The programmed name and number are printed at the top of each fax page you send. The number is also used as a passcode when performing polling reception "USING THE POLLING FUNCTION" (page 36).

You can check your programmed name and number by printing out the "SYSTEM SET LIST". (Page 99)

•A maximum of 20 digits can be stored for the fax number.

•A maximum of 18 letters can be stored for the name.

1	Follow steps 1 through 6 of "INITIAL
	PROCEDURE" (page 98).
2	Select "INITIAL SETTING" with the [ ] or
	[	] key and then press the [OK] key.
3	Select "OWN PASSCODE SET" with the
	[	] or [ ] key and then press the [OK]
	key.
4	Select "STORE" with the [ ] or [ ] key
	and then press the [OK] key.
5	Enter your fax number with the numeric
	keys and then press the [OK] key.

•If you make a mistake, press the [C] key and re-enter the number.

•To enter "+", press the key.

6 Enter your name and then press the [START] key ( ).

See "ENTERING CHARACTERS" (page 86) for the procedure for entering letters.

Note	To clear the programmed fax number and
	name, follow these steps:

(1)Select "DELETE" in step 4 and then press the [OK] key.

(2)Select "DELETE" with the [ ] or [ ] key and then press the [OK] key.

SPEAKER VOLUME

This setting is used to adjust the on-hook volume, the ringing volume, the line monitor volume, the TX/RX end sound volume, the original scanning end sound volume, and the tone output volume. All volume settings are initially set to "MIDDLE".

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key.

3 Select "SPEAKER VOLUME" with the [ ] or [ ] key and then press the [OK] key.

4 Select name of the volume that you wish to adjust with the [ ] or [ ] key and then press the [OK] key.

5 Select the desired volume level with the

[ ] or [ ] key and then press the [OK] key.

•"HIGH", "MIDDLE" or "LOW" can be selected for the on hook volume.

•"HIGH", "MIDDLE", "LOW" or "OFF" can be selected for volumes other than the on hook volume.

TX/RX END SOUND

This setting is used to select the beep pattern that signals the end of transmission or reception. "PATTERN 1", "PATTERN 2" or "PATTERN 3" can be selected.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "INITIAL SETTING" with the [ ] or [ ] key and then press the [OK] key.

3 Select "TX/RX END SOUND" with the [ ] or [ ] key and then press the [OK] key.

4 Select "SEND" or "RECEIVE" with the [ ] or [ ] key and then press the [OK] key.

5 Select "PATTERN 1", "PATTERN 2", or "PATTERN 3" with the [ ] or [ ] key and then press the [OK] key.

Before pressing the [OK] key to store your selection, you can press the key to listen to the selected pattern.

TX/RX END SOUND LENGTH

This setting is used to select the length of the end sound in seconds. Selections are "2.0 sec", "2.5 sec", "3.0 sec", "3.5 sec", and "4.0 sec". "3.0 sec" is normally selected.

1	Follow steps 1 through 6 of "INITIAL
	PROCEDURE" (page 98).
2
	Select "INITIAL SETTING" with the [ ] or		8
	[ ] key and then press the [OK] key.
3	Select "TX/RX END SOUND LENGTH" with
	the [	] or [ ] key and then press the [OK]
	key.
4	Select the number of seconds with the [ ]
	or [	] key and then press the [OK] key.

101