Sharp MX-FX13 appendix Polling Security, 111, Enter Junk FAX #, Polling Passcode # Mode

SYSTEM SETTINGS

ENTER JUNK FAX #

This setting is used to program fax numbers from which you wish to block reception. Up to 50 fax numbers can be stored (maximum of 20 digits each). To block reception from the programmed fax numbers, the "ANTI JUNK FAX" setting must be enabled.

1	Follow steps 1 through 6 of "INITIAL
	PROCEDURE" (page 98).
2	Select "RCV. FUNCTION" with the [	] or
	[ ] key and then press the [OK] key.
3	Select "ENTER JUNK FAX #" with the [ ]
	or [ ] key and then press the [OK] key.
4	Select "ENTER" with the [ ] or [	] key
	and then press the [OK] key.
5	Enter a 2-digit control number from 01 to
	50 with the numeric keys to identify the fax
	number that will be entered in the next
	step, and then press the [OK] key.
6	Enter the fax number that you wish to
	block with the numeric keys, and then

press the [OK] key.

To delete a number, follow these steps: Note Before deleting a number, use the "LIST

PRINT" setting on (page 99) to check the control number that identifies the fax number (01 to 50) that you wish to delete. The control number must be entered to delete the fax number. (The fax number will not appear in the display. If the wrong control number is accidentally entered, a fax number other than the fax number that you wish to delete will be deleted.)

(1)Select "DELETE" in step 4 and then press the [OK] key.

(2)Select the 2-digit control number (01 to 50) that identifies the fax number that you wish to delete with the [ ] or [ ] key and then press the [OK] key.

(3)Select "DELETE" with the [ ] or [ ] key and then press the [OK] key.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "POLLING SECURITY" with the [ ] or [ ] key and then press the [OK] key.

3 Select "POLLING SECURITY" with the [ ] or [ ] key and then press the [OK] key.

•The setting is enabled and a checkmark appears in the checkbox.

•If this procedure is performed when the setting is enabled, the checkmark will be cleared and the setting disabled.

POLLING PASSCODE # MODE

When "POLLING SECURITY" is enabled, use this setting to program (or delete) the fax numbers of the machines that are allowed to poll your machine. Programmed fax numbers are called passcodes. Up to 10 fax numbers can be programmed. To check the programmed numbers, print the "SYSTEM SET LIST" (page 99).

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "POLLING SECURITY" with the [ ] or [ ] key and then press the [OK] key.

3 Select "POLLING PASSCODE # MODE" with the [ ] or [ ] key and then press the [OK] key.

4	Select "ENTER" with the [ ] or [ ] key
	and then press the [OK] key.
5	Enter a 2-digit control number from 01 to 10

with the numeric keys to identify the passcode that will be entered in the next step, and then press the [OK] key.

If you make a mistake, move the cursor to the mistake with the [ ] or [ ] keys and enter the correct number.

POLLING SECURITY

These settings are used for the public box for regular polling memory. Note that they do not apply to F-code polling memory. (See "USING POLLING MEMORY" page 38.)

POLLING SECURITY

When performing polling memory (see "Polling security" on page 40), this setting is used to select whether any machine will be allowed to poll your machine, or only machines that have been programmed in your machine. Normally this setting is enabled.

6 Enter the passcode number (up to 20	8
digits) and then press the [OK] key.
If you make a mistake, press the [C] key and then

re-enter the correct number.

To clear a passcode number, follow these

Note steps:

(1)Select "DELETE" in step 4 and then press the [OK] key.

(2)Enter the control number that identifies the number you wish to clear, and then press the [OK] key.

(3)Select "DELETE" with the [ ] or [ ] key and then press the [OK] key.

111