Sharp MX-FX13 appendix 107, Recall SET ERR, Ring Timeout in Auto TX

	SYSTEM SETTINGS
5 Enter the recall interval (01 to 15)* with the	7 Enter the number of recall attempts with the
numeric keys and then press the [OK] key.	numeric keys and then press the [OK] key.

•The recall interval can be set from 1 to 15* minutes.

•After finishing step 5, if you do not wish to change the number of recall attempts, press the [BACK] key to exit.

*Varies depending on country and region.

•If you do not wish to have recalling take place, set the number of attempts to "0".

•If the recall interval is set to "0", the machine will immediately call again after the connection is broken due to the line error.

6	Select "RECALL TIMES" with the [ ] or
	[ ] key and then press the [OK] key.
7	Enter the number of recall attempts with the
	numeric keys and then press the [OK] key.

•If you do not wish to have recalling take place, set the number of attempts to "0".

• If you made a mistake in step 5 or step 7,

Note move the cursor to the mistake with the [ ] or [ ] key and enter the correct number.

•Even if this setting is enabled, the machine will not re-attempt the call when a fax is sent by manual transmission.

RECALL SET (ERR)

When sending a fax, this setting is used to select whether or not the machine will automatically re-attempt the call if the transmission fails due to a line error. Normally the machine is set to make 1* recall attempt at intervals of 1* minute.

If you do not wish to have recalling take place, set the number of attempts to "0" (steps 6 and 7).

* Varies depending on country and region.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "SENDING FUNCTION" with the [ ] or [ ] key and then press the [OK] key.

3 Select "RECALL SET(ERR)" with the [ ] or [ ] key and then press the [OK] key.

If you do not wish to change the recall interval setting, go to step 6.

• If you made a mistake in step 5, move the

Note cursor to the mistake with the [ ] or [ ] keys and enter the correct number.

•Even if this setting is enabled, the machine will not re-attempt the call when a fax is sent by manual transmission.

RING TIMEOUT IN AUTO TX

When sending a fax by automatic transmission (see "Storing transmission jobs (memory transmission)" on page 23), this setting lets you select the amount of time that the machine waits before breaking the connection when the other machine does not answer your machine's call. If the other machine does not respond within this set time, your machine will automatically break the connection.

Time selections are "30 SEC.", "45 SEC." and "60 SEC.". Normally "45 SEC." is selected.*

* Varies depending on country and region.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "SENDING FUNCTION" with the [ ] or [ ] key and then press the [OK] key.

3 Select "RING TIMEOUT IN AUTO TX" with the [ ] or [ ] key and then press the [OK] key.

4 Select the time with the [ ] or [ ] key and then press the [OK] key.

Selections for the call time are "30 SEC.", "45 SEC.", "60 SEC.".*

* Varies depending on country and region.

4

5

Select "RECALL INTERVAL" with the [ ]	8
or [ ] key and then press the [OK] key.
Enter the recall interval (00 to 15) with the

numeric keys and then press the [OK] key.

•The recall interval can be set from 0 to 15 minutes.

•After finishing step 5, if you do not wish to change the number of recall attempts, press the [BACK] key to exit.

6 Select "RECALL TIMES" with the [ ] or [ ] key and then press the [OK] key.

107