Sharp MX-FX13 110, FW. RX Data, Received Data FW. Station SET, Earlier Output, Anti Junk FAX

SYSTEM SETTINGS

FW. RX DATA

This setting is used to select whether or not received faxes are forwarded to a fax machine programmed as explained in "RECEIVED DATA FW. STATION SET" (page 110) in the event that the machine cannot print the faxes. The setting is initially disabled.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2	Select "RCV. FUNCTION" with the [	] or
	[ ] key and then press the [OK] key.
3	Select "FW. RX DATA" with the [	] or [ ]
	key and then press the [OK] key.

•The setting is enabled and a checkmark appears in the checkbox.

•If the procedure is performed when the setting is enabled, the checkmark will be cleared and the setting disabled.

This setting only operates when the fax Note number of the machine that is to receive the

forwarded faxes is programmed.

RECEIVED DATA FW. STATION SET

When a problem prevents the machine from printing a received fax, the fax forwarding function (page 49) can be used to forward the received fax to another fax machine. Use this setting to program the fax number of the destination fax machine. Only one fax number can be programmed (maximum of 50 digits).

To specify an F-code confidential box in the destination fax machine, enter the sub-address and passcode after the fax number in steps 6 and 7 below.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "RCV. FUNCTION" with the [ ] or [ ] key and then press the [OK] key.

3 Select "RECEIVED DATA FW. STATION SET" with the [ ] or [ ] key and then press the [OK] key.

4 Select "STORE" with the [ ] or [ ] key and then press the [OK] key.

5 Enter the forwarding fax number with the numeric keys and then press the [OK] key.

6 Enter the sub-address with the numeric keys and then press the [OK] key.

If you do not need to specify an F-code confidential box in the destination fax machine, press the [OK] key without entering anything.

7 Enter the passcode with the numeric keys and then press the [OK] key.

If you do not need to specify an F-code confidential box in the destination fax machine, press the [OK] key without entering anything.

To delete the number, follow these steps: Note (1) Select "DELETE" in step 4 and then

press the [OK] key.

(2)Select "DELETE" with the [ ] or [ ] key and then press the [OK] key.

EARLIER OUTPUT

When a received fax cannot be printed because the machine is out of appropriate paper and a fax is subsequently received that can be printed, this setting determines whether the subsequent fax is printed before the fax that cannot be printed. The setting is initially enabled (the subsequent fax is printed first).

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "RCV. FUNCTION" with the [ ] or [ ] key and then press the [OK] key.

3 Select "EARLIER OUTPUT" with the [ ] or [ ] key and then press the [OK] key.

•The setting is enabled (the subsequent fax is printed first) and a checkmark appears in the checkbox.

•If the procedure is performed when the setting is enabled, the checkmark will be cleared and the setting disabled.

ANTI JUNK FAX

When this setting is enabled, reception from fax numbers programmed using the "ENTER JUNK FAX #" program will be blocked.

This program is normally disabled.

1 Follow steps 1 through 6 of "INITIAL PROCEDURE" (page 98).

2 Select "RCV. FUNCTION" with the [ ] or [ ] key and then press the [OK] key.

3 Select "ANTI JUNK FAX" with the [ ] or

[ ] key and then press the [OK] key.

•The setting is enabled and a checkmark appears in the checkbox.

•If this procedure is performed when the setting is enabled, the checkmark will be cleared and the setting disabled.

110