HP 132A, 53131A manual On OFF Once

Chapter 2 Command Summary

HP 53131A/132A Command Summary

Table 2-2. HP 53131A/132A SCPI Command Summary (Continued)

Keyword/Syntax	Parameter Form				Std/	Comments
					New
[:SENSe] (Cont.)					Std	Subtree. Selects the <sensor function> to
:FUNCtion
						be sensed by the instrument.
[:ON]	<sensor_function> (See below)				Std	Sets the <sensor function> to be sensed by
						the instrument.
	“[:][XNONe:]DCYCle	[1] ”			New	(Positive) duty cycle on channel 1.
	“[:][XNONe:]PDUTycycle			[1] ”	New	(Positive) duty cycle on channel 1.
	“[:][XNONe:]FALL:TIME			[1] ”	New	Fall Time on channel 1.
	“[:][XNONe:]FTIMe [1] ”				New	Fall Time on channel 1.
	“[:][XNONe:]FREQuency			[1 2 3] ”	Std	Frequency on channel 1, 2, or 3.
	“[:][XNONe:]FREQuency:RATio				Std	1Frequency Ratio 1 to 2, 1 to 3, 2 to 1, or 3
	[1,2 1,3 2,1 3,1] ”					to 1.
	“[:][XNONe:]NWIDth	[1] ”			New	Negative Pulse Width on channel 1.
	“[:][XNONe:]PERiod	[1 2 3] ”			Std	Period on channel 1, 2, or 3.
	“[:][XNONe:]PHASe	[1,2] ”			Std	Phase of channel 1 relative to channel 2.
	“[:][XNONe:]PWIDth	[1] ”			New	Positive Pulse Width on channel 1.
	“[:][XNONe:]RISE:TIME [1] ”				New	Rise Time on channel 1.
	“[:][XNONe:]RTIMe [1] ”				New	Rise Time on channel 1.
	“[:][XNONe:]TINTerval		[1,2] ”		New	Time Interval channel 1 to channel 2.
	“[:][XNONe:]TOTalize		[1] ”		Std	Totalize on channel 1.
	“[:][XNONe:]VOLTage:MAXimum [1 2] ”				Std	Voltage Maximum on channel 1 or 2.
	“[:][XNONe:]VOLTage:MINimum [1 2] ”				New	Voltage Minimum on channel 1 or 2.
	“[:]{XNONe:]VOLTage:PTPeak [1 2]				New	Voltage Peak to Peak on Channel 1 or 2.
:PHASe					New	Subtree. Controls the phase measuring
					New	capabilities of the instrument.
:ARM						Subtree.
[:STARt]					New	Subtree. Synchronizes Phase start arm with
	POSitive NEGative				New	events.
:SLOPe						Sets the slope of the external start arm
						signal used in external arming phase
						measurements. Only applies when
						[:SENS]:PHAS:ARM[:STAR]:SOUR EXT is
	IMMediate EXTernal				New	selected.
:SOURce						Sets the start arm for phase
:ROSCillator					Std	measurements.
:EXTernal					Std	Subtree. Controls the Reference
:CHECk	ON OFF ONCE				New	OSCillator.
					Std	Subtree.
:FREQuency?						Set the enable for checking the validity and
						presence of the external reference.
						Query only. Returns the frequency value of
						the external reference oscillator.
	______________________________
	1For HP 53131A firmware revision s below 3335, only Ratio 1 to 2 and Ratio 1 to 3 were offered.

2-34 Programming Guide