Scs, Fcs, FrY | Schneider Electric 61 instruction

Configuration saving and switching

Function parameters

Code		Description

SCS	Parameter name:	Save configuration

	Logic address:	8001 = 16#1F41	Type:	WORD (listing)
	CANopen index:	2032/2	Read/write:	R/WS
	INTERBUS index:	5FBC/9A
	DeviceNet path:	9C/01/9A

	0 = No save
	1 = Save to configuration no. 0
	2 = Save to configuration no. 1
	3 = Save to configuration no. 2

FCS	Parameter name:	Restore configuration

	Logic address:	8002 = 16#1F42	Type:	WORD (listing)
	CANopen index:	2032/3	Read/write:	R/WS
	INTERBUS index:	5FBC/9B
	DeviceNet path:	9C/01/9B

	0 = No restore
	1 = Restore configuration no. 0
	2 = Restore configuration no. 1
	3 = Restore configuration no. 2
	64 = Factory setting

FrY	Parameter name:	Parameter groups
	Terminal display:	[PARAMETER GROUP LIST]

	Logic address:	3022 = 16#OBCE	Type:	WORD (bit register)
	CANopen index:	2000/17	Read/write:	R/WS
	INTERBUS index:	5FBC/06	Factory setting:	0
	DeviceNet path:	70/01/17

	Selection of menus to be loaded
	bit 0: = 1: [All] (ALL): All parameters
	bit 1: = 1: [Drive menu] (drM): The [1 DRIVE MENU] menu without [1.9 COMMUNICATION] and [1.14 CONTROL
	INSIDE MENU]. In the [7 DISPLAY CONFIG.] menu, [Return std name] returns to [No]
	bit 2: = 1: [Settings] (SEt): The [1.3 SETTINGS] menu without the [IR compensation] (UFr), [Slip compensation] (SLP)
	and [Mot. therm. current] (ItH) parameters
	bit 3: = 1: [Motor param] (MOt): Motor parameters:
	[Rated motor power] (nPr) - [Rated motor volt.] (UnS) - [Rated mot. current] (nCr) - [Rated motor freq.] (FrS) -
	[Rated motor speed] (nSP) - [Auto tuning] (tUn) - [Auto tuning state] (tUS) - [U0] (U0) to [U5] (U5) - [F1] (F1) to
	[F5] (F5) - [V. constant power] (UCP) - [Freq. Const Power] (FCP) - [Nominal I sync.] (nCrS) - [Nom motor
	spdsync] (nSPS) - [Pole pairs] (PPnS) - [Syn. EMF constant] (PHS) - [Autotune L d-axis] (LdS) - [Autotune L q-
	axis] (LqS) - [Cust. stator R syn] (rSAS) - [IR compensation] (UFr) - [Slip compensation] (SLP) - the motor
	parameters that can be accessed in [Expert] mode
	The following options can only be accessed if [Config. Source] (FCSI) = [Macro-Conf](InI):
	bit 4: = 1: [Comm. menu] (COM): The [1.9 COMMUNICATION] menu without either [Scan. IN1 address] (nMA1) to
	[Scan. IN8 address] (nMA8) or [Scan.Out1 address] (nCA1) to [Scan.Out8 address] (nCA8)
	bit 5: = 1: [Control Inside menu] (PLC): The [1.14 CONTROL INSIDE MENU] menu
	bit 6: = 1: [Monitor config.] (MOn): The [6 MONITORING CONFIG.] menu
	bit 7: = 1: [Display config.] (dIS): The [7 DISPLAY CONFIG.] menu
	bits 8 to 15: Reserved (= 0 or 1)

66

Image 66

Schneider Electric 61 user manual Scs, Fcs, FrY

Contents

Altivar Page Contents Contents Programming manual Installation ManualDocument structure and directions for use Communication Parameters Manual Presentation Interbus Presentation Enhancements made to version V1.2 in comparison to Factory settingSoftware enhancements Enhancements made to version V1.4 in comparison to Enhancements made to version V1.5 in comparison to Enhancements made to version V1.6 in comparison to Notations Description of parametersDrive terminal displays What is a profile? Profiles CiA402 profile Functional profiles supported by Altivar 61 drivesProfile Odva profile Command CtL Profile Chcf Profile IO ProfileDefinition Controller Inside control word Control word run on state 2 wire 2C Fixed assignments Control word run on edge 3 wire 3C Status word ETA Bit CiA402 profile Functional description Power section line supply present CiA402 state chartPower section line supply present or absent Fault Examples Description of states Quick stop active Fault reaction activeFault Summary Bit Assignable Final state Example value Fault Enable QuickControl word CMD Transition Bit Stop commands Assigning control word bits Status Ready to Starting sequence Drive Bus or network Enable Sequence for a drive with separate control section Shutdown Switch on Power section line supply Terminal display Status word Enable Sequence for a drive with line contactor control Shutdown Switch on Enable Command/reference switching Channel commands and referencesChannels Command CtL Profile Chcf Not separ. SIM Not separate modeSeparate mode Command CtL Profile Chcf Separate SEP Switching in not separate mode Switching in separate mode Command channel configuration Channel switchingReference channel configuration Terminals tEr Terminals Switches Reference switching principle AI1 Command switching principle Profile or CiA402 profile separate modeCiA402 profile not separate mode Assigning control word bits Example Run on state command 2 wire 2C Run on edge command 3 wire 3C LI1 Copy on switching Forced local mode Forced local mode and reference switching AI3C AI4C Forced local mode and command switching CiA402 profile separate modeRun Stop Forward Reverse AI1 Priority stops Priority stops on the graphic display terminalPriority stops via the terminals or the network Freewheel stop ass Channel Run on state command Run on edge commandOperation enabled DC injection assign Communication monitoring PrincipleNetwork monitoring criteria CANopen com. COF for CANopen Behavior in the event of a network faultFast stop FSt Fast stop Ignore nO Detailed operation Monitoring of communication channels Enabling of communication channels Special case involving Modbus TCP/IP Ethernet card Assignment of references from a network Reference parameters SA2, SA3, dA2, dA3 Without PID regulatorFr1, Fr1b, Fr2 MA2, MA3 Fr2, FPI With PID regulatorFr1, Fr1b Key Configuration saving and switching Saving the configuration Modbus CANopen Network Set to Restore configuration CFG Configuration switching via control word ConfigurationsCnF1 ConfigurationsCnF2 Cnfs CNF2 Function parametersCNF1 Cnfs Description/Condition Configuration switching by selection CFG SCS FCSFrY CHA2 Parameter set switchingCHA1 Cfps CHA1 and CHA2 assignment values AD03 AD01AD02 AD04 S203 S201S202 S204 Load parameter set command Load the configuration ProcedureSaving the reference configuration Loading drive parameters Inconsistency examples Example Cmd value Command parametersControl word Freewheel stop Freewheel stop ass. nSt Code Extended control word LFR Setpoint parametersLfrd Frequency ref Pisp AIU1 Status parameters ETA Possible values in CiA402 profile ETI Extended status wordLRS1 LRS2 LRS3 LRS4 LRS5 LRS6 LRS7 LRS8 CRCActive reference channel Active command channel CCC RFr Output value parametersOutput values speed Output frequency Output torque Output values torqueOtr Motor torque UOP Output values motorLCr OPr Reference parameters References speed RPF References regulatorRPC RPE ULn Measurement parametersInput measurements IPr THr Thermal statesTHd THb Time Total process operating time Format of Date and Time parametersPEt Proc. Operat. Time Logic input map ParametersLogic I/O OL1r AI2C Analog inputsAI1C AI3C AO1C Analog outputsAI4C AO2C AO3C EncoderAO2r AO3r Fault parameters CiA402 fault codeErrd 101 LFt PowerSuite com External fault comApplication fault Power removal CIC APFCnF ILF2 FDR faultILF1 Fdrd Fault counter Fnb ULP0 Description of last fault logLog parameters LCP0 DCC0 IP0CMP0 DrC0 CrPO RtP0 110 Log of the following faults EP3 ULP3LCP3 IP3 EP5 ULP5LCP5 IP5 EP7 ULP7LCP7 IP7 Ucal Identification parametersNCVr InV PAn2 PAn0PAn1 PAn3 PAn7 PAn6Device name characters 13 Device name characters 15 Smal CiA402 standard configuration and adjustment parametersSmil Spal Deceleration DEC SPAtSPdL SPdt SPFd SPFnSpeed setpoint factor numerator Speed setpoint factor denominator Qstd Disable operation option codeDotd Quick stop option code DECd Odva standard configuration and adjustment parametersACCd LSPd Index of parameter codes Code Name CMP6 EP0 EP7 LCP3 PUC SCS ULP0 Atv61parametersenv4 2008-03