Log of the following faults | Schneider Electric 61 instruction

Log parameters

Log of the following faults

The log shown for the first fault can be used to review the last 8 faults. All codes and addresses are summarized in the tables below.

Fault n-1

Log	Code	Logic address:	CANopen	INTERBUS	DeviceNet
			index:	index:	path:

Fault code	dP1	7201 = 16#1C21	202A/2	5FB9/5A	85/01/02

Power supply voltage	ULP1	7271 = 16#1C67	202A/48	5FB9/99	85/01/48

Motor current	LCP1	7241 = 16#1C49	202A/2A	5FB9/7E	85/01/2A

Output frequency	rFP1	7251 = 16#1C53	202A/34	5FB9/87	85/01/34

Motor thermal state	tHP1	7281 = 16#1C71	202A/52	5FB9/A2	85/01/52

Status word	EP1	7211 = 16#1C2B	202A/C	5FB9/63	85/01/0C

Extended status word	IP1	7221 = 16#1C35	202A/16	5FB9/6C	85/01/16

Command word	CMP1	7231 = 16#1C3F	202A/20	5FB9/75	85/01/20

Active command channel	dCC1	64301 = 16#FB2D		5FBA/22

Active reference channel	drC1	64311 = 16#FB37		5FBA/2B

Active channels	CrP1	7291 = 16#1C7B	202A/5C	5FB9/AB	85/01/5C

Motor operating time	rtP1	7261 = 16#1C5D	202A/3E	5FB9/90	85/01/3E

Date	Md1	7301 = 16#1C85	202B/2	5FB9/B4	85/01/66

Time	dM1	7311 = 16#1C8F	202B/C	5FB9/BD	85/01/70

Fault n-2

Log	Code	Logic address:	CANopen	INTERBUS	DeviceNet
			index:	index:	path:

Fault code	dP2	7202 = 16#1C22	202A/3	5FB9/5B	85/01/03

Power supply voltage	ULP2	7272 = 16#1C68	202A/49	5FB9/9A	85/01/49

Motor current	LCP2	7242 = 16#1C4A	202A/2B	5FB9/7F	85/01/2B

Output frequency	rFP2	7252 = 16#1C54	202A/35	5FB9/88	85/01/35

Motor thermal state	tHP2	7282 = 16#1C72	202A/53	5FB9/A3	85/01/53

Status word	EP2	7212 = 16#1C2C	202A/D	5FB9/64	85/01/0D

Extended status word	IP2	7222 = 16#1C36	202A/17	5FB9/6D	85/01/17

Command word	CMP2	7232 = 16#1C40	202A/21	5FB9/76	85/01/21

Active command channel	dCC2	64302 = 16#FB2E		5FBA/23

Active reference channel	drC2	64312 = 16#FB38		5FBA/2C

Active channels	CrP2	7292 = 16#1C7C	202A/5D	5FB9/AC	85/01/5D

Motor operating time	rtP2	7262 = 16#1C5E	202A/3F	5FB9/91	85/01/3F

Date	Md2	7302 = 16#1C86	202B/3	5FB9/B5	85/01/67

Time	dM2	7312 = 16#1C90	202B/D	5FB9/BE	85/01/71

111

Image 111

Schneider Electric 61 user manual Log of the following faults

Contents

Altivar Page Contents Contents Communication Parameters Manual Installation ManualDocument structure and directions for use Programming manual Interbus Presentation Presentation Enhancements made to version V1.4 in comparison to Factory settingSoftware enhancements Enhancements made to version V1.2 in comparison to Enhancements made to version V1.6 in comparison to Enhancements made to version V1.5 in comparison to Notations Description of parametersDrive terminal displays Profiles What is a profile? Odva profile Functional profiles supported by Altivar 61 drivesProfile CiA402 profile Command CtL Profile Chcf Profile IO ProfileDefinition Controller Inside control word Fixed assignments Control word run on state 2 wire 2C Control word run on edge 3 wire 3C Bit Status word ETA Functional description CiA402 profile Examples CiA402 state chartPower section line supply present or absent Fault Power section line supply present Description of states Summary Fault reaction activeFault Quick stop active Transition Bit Final state Example value Fault Enable QuickControl word CMD Bit Assignable Assigning control word bits Stop commands Ready to Status Drive Starting sequence Bus or network Enable Shutdown Sequence for a drive with separate control section Power section line supply Terminal display Status word Switch on Enable Shutdown Sequence for a drive with line contactor control Switch on Enable Command/reference switching Channel commands and referencesChannels Command CtL Profile Chcf Separate SEP Not separate modeSeparate mode Command CtL Profile Chcf Not separ. SIM Switching in separate mode Switching in not separate mode Terminals tEr Terminals Channel switchingReference channel configuration Command channel configuration Switches AI1 Reference switching principle Command switching principle Profile or CiA402 profile separate modeCiA402 profile not separate mode Example Assigning control word bits Run on edge command 3 wire 3C Run on state command 2 wire 2C LI1 Copy on switching Forced local mode AI3C AI4C Forced local mode and reference switching Forced local mode and command switching CiA402 profile separate modeRun Stop Forward Reverse AI1 Priority stops Priority stops on the graphic display terminalPriority stops via the terminals or the network DC injection assign Channel Run on state command Run on edge commandOperation enabled Freewheel stop ass Communication monitoring PrincipleNetwork monitoring criteria Ignore nO Behavior in the event of a network faultFast stop FSt Fast stop CANopen com. COF for CANopen Monitoring of communication channels Detailed operation Special case involving Modbus TCP/IP Ethernet card Enabling of communication channels Reference parameters Assignment of references from a network MA2, MA3 Without PID regulatorFr1, Fr1b, Fr2 SA2, SA3, dA2, dA3 Key With PID regulatorFr1, Fr1b Fr2, FPI Saving the configuration Configuration saving and switching Modbus CANopen Network Set to CFG Restore configuration ConfigurationsCnF1 ConfigurationsCnF2 Configuration switching via control word Cnfs Cnfs Function parametersCNF1 CNF2 Description/Condition CFG Configuration switching by selection SCS FCSFrY Cfps Parameter set switchingCHA1 CHA2 CHA1 and CHA2 assignment values AD04 AD01AD02 AD03 S204 S201S202 S203 Load parameter set command Loading drive parameters ProcedureSaving the reference configuration Load the configuration Example Inconsistency examples Freewheel stop Freewheel stop ass. nSt Command parametersControl word Cmd value Code Extended control word Frequency ref Setpoint parametersLfrd LFR AIU1 Pisp ETA Status parameters Possible values in CiA402 profile ETI Extended status wordLRS1 LRS3 LRS2 LRS5 LRS4 LRS7 LRS6 LRS8 CRCActive reference channel CCC Active command channel Output frequency Output value parametersOutput values speed RFr Motor torque Output values torqueOtr Output torque OPr Output values motorLCr UOP References speed Reference parameters RPE References regulatorRPC RPF IPr Measurement parametersInput measurements ULn THb Thermal statesTHd THr Time Proc. Operat. Time Format of Date and Time parametersPEt Total process operating time OL1r ParametersLogic I/O Logic input map AI3C Analog inputsAI1C AI2C AO2C Analog outputsAI4C AO1C AO3r EncoderAO2r AO3C Fault parameters CiA402 fault codeErrd 101 LFt Power removal External fault comApplication fault PowerSuite com CIC APFCnF Fdrd FDR faultILF1 ILF2 Fnb Fault counter LCP0 Description of last fault logLog parameters ULP0 DrC0 IP0CMP0 DCC0 RtP0 CrPO 110 Log of the following faults IP3 ULP3LCP3 EP3 IP5 ULP5LCP5 EP5 IP7 ULP7LCP7 EP7 InV Identification parametersNCVr Ucal PAn3 PAn0PAn1 PAn2 Device name characters 15 PAn6Device name characters 13 PAn7 Spal CiA402 standard configuration and adjustment parametersSmil Smal SPdt SPAtSPdL Deceleration DEC Speed setpoint factor denominator SPFnSpeed setpoint factor numerator SPFd Quick stop option code Disable operation option codeDotd Qstd LSPd Odva standard configuration and adjustment parametersACCd DECd Code Name Index of parameter codes CMP6 EP0 EP7 LCP3 PUC SCS ULP0 Atv61parametersenv4 2008-03