Client Associations, Name Ssid | USRobotics Instant802 APSDK

Professional Access Point

Administrator Guide

This page provides basic information about the current access point and a real-time display of the transmit and receive statistics for this access point as described in the table below. All transmit and receive statistics shown are totals accumulated since the access point was last started. If the access point is rebooted, these figures indicate transmit/receive totals since the reboot.

Field

Description

IP Address	IP Address for the access point.

MAC Address	Media Access Control (MAC) address for the specified interface.
	The Professional Access Point has a unique MAC address for each interface.

VLAN ID	Virtual LAN (VLAN) ID.
	A VLAN is a software-based, logical grouping of devices on a network that
	allow them to act as if they are connected to a single physical network, even
	though they may not be.
	VLANs can be used to establish internal and guest networks on the same
	access point.

Name (SSID)	Wireless network name. Also known as the SSID, this alphanumeric key
	uniquely identifies a wireless local area network.
	The SSID is set on the Basic Settings tab. (See “Provide Administrator Pass-
	word and Wireless Network Name” on page 38.)

Transmit and Receive Information

Total Packets	The total count of packets sent (in the Transmit table) or received (in the
	Received table) by this access point.

Total Bytes	The total count of bytes sent (in the Transmit table) or received (in the Received
	table) by this access point.

Errors	The total count of errors related to sending and receiving data on this access
	point.

Client Associations

To view the client stations associated with a particular access point, navigate to the

Status menu’s Client Associations on the Web User Interface for the access point that you want to monitor.

Client Associations - 83

Image 83

USRobotics Instant802 APSDK manual Client Associations, Name Ssid, Total Packets, Total Bytes, Errors

Contents

R46.1224.00 rev 2.0 07/06 Professional Access Point Administrator GuidePage USA Professional Access Point Administrator Guide Professional Access Point Administrator Guide Contents Support Information Class Structure, Commands, and ExamplesAdvanced Class and Field Reference Robotics Corporation Two 2 Year Limited Warranty Viii Online Help Features Administrator Audience Typographical Conventions Recommended Settings, Notes and Cautions Getting Started Security Features Features and BenefitsIeee Standards Support and Wi-Fi Compliance Wireless Features Networking Guest InterfaceClustering and Auto-Management Maintainability What’s Next?Snmp Support Professional Access Point Option Default Settings Related Information Default Settings for the Professional Access Point Authentication Type Ieee 802.11 ModeTransmit Power Security Mode None Required Software or Component Description Administrator’s ComputerWhat the Access Point Does Not Provide Required Component Description Wireless Client Computers Required Component How Does the Access Point Obtain an IP Address at Startup?Dynamic IP Addressing Static IP Addressing Recovering an IP Address Professional Access Point Administrator Guide What’s inside the Access Point? Unpack the access pointAccess Point Hardware and Ports Connect the access point to network and power UK Users Hardware Connections for a Guest Vlan Professional Access Point Administrator Guide Professional Access Point Administrator Guide Professional Access Point Administrator Guide Username Viewing Basic Settings for Access PointsField Default Setting Log on to the Web User Interface Configure Basic Settings and start the wireless network Default Configuration Make Sure the Access Point is Connected to the LAN Wall Mounting the Access Point Test LAN Connectivity with Wireless Clients Web User Interface Navigating to Basic Settings Firmware Version Review / Describe the Access PointField Description MAC Address Wireless Network Name Ssid Provide Administrator Password and Wireless Network NameAdministrator Password Administrator Password again Field Set Configuration Policy for New Access PointsNew Access Points Summary of Settings Update Basic Settings Icon Description Basic Settings for a Standalone Access PointYour Network at a Glance Understanding Indicator Icons Professional Access Point Administrator Guide Cluster Access Points Understanding Clustering Navigating to Access Points Management What Kinds of APs Can Cluster? What is a Cluster?How Many APs Can a Cluster Support? Settings Not Shared by the Cluster Cluster Formation Cluster ModeStandalone Mode Intra-Cluster Security Understanding Access Point SettingsAuto-Synchronization of Cluster Configuration Cluster Size and Membership Modifying the Location Description Removing an Access Point from the Cluster Http//IPAddressOfAccessPoint Adding an Access Point to a Cluster Professional Access Point Administrator Guide Professional Access Point Administrator Guide User Management Adding a User Navigating to User Management for Clustered Access PointsViewing User Accounts Real Name Editing a User AccountEnabling and Disabling User Accounts Enabling a User Account Disabling a User Account Restoring a User Database from a Backup FileRemoving a User Account Backing Up and Restoring a User Database Professional Access Point Administrator Guide Professional Access Point Administrator Guide Navigating to Session Monitoring Sessions User AP Location User MAC Idle Rate Understanding Session Monitoring Information Refreshing Session Information Viewing Session Information for Access PointsSignal Utilization Rx Total Tx Total Error Rate Sorting Session Information Professional Access Point Administrator Guide Channel Management Overlapping Channels Background Information Navigating to Channel ManagementUnderstanding Channel Management How it Works Overview Example a Network before and after Channel Management Configuring and Viewing Channel Management Settings Stopping/Starting Automatic Channel Assignment IP Address Current Proposed Viewing Current Channel Assignments and Setting LocksViewing Last Proposed Set of Changes IP Address Band Current Locked Determine if there is better set of channels every Use these channels when applying channel assignmentsAdvanced Change channels if interference is reduced by at least Apply channel modifications even when the network is busy Professional Access Point Administrator Guide Wireless Neighborhood Understanding Wireless Neighbourhood Information Navigating to Wireless Neighborhood Cluster Viewing Wireless NeighborhoodDisplay neighboring APs Neighbors Details for a Cluster Member AP Viewing Details for a Cluster Member Beacon Age SignalChannel Interfaces Status Wireless Settings Ethernet Wired Settings Log Relay Host for Kernel Messages Events Tmp/APsyslog Setting Up the Log Relay HostUnderstanding Remote Logging SYSLOGD=-r Relay Host Log Relay Host EnabledEnabled Etc/init.d/sysklogd restart Events Log Transmit/Receive Statistics Total Packets ErrorsClient Associations Name Ssid Link Integrity Monitoring What is the Difference Between an Association and a Session? Select AP Detection Enabled Neighboring Access Points Privacy Beacon IntType Rates # of BeaconsLast Beacon Professional Access Point Administrator Guide Advanced Ethernet Wired Settings Navigating to Ethernet Wired Settings Enabling and Disabling Guest Access Setting the DNS NameManaging Guest Access Configuring an Internal LAN and a Guest Network Specifying a Virtual Guest Network Guest AccessFor Guest access, use Virtual Wireless Networks Configuring Internal Interface Ethernet Settings DNS Nameservers Default GatewayStatic IP Address Subnet Configuring Guest Interface Ethernet Wired SettingsUpdating Settings Professional Access Point Administrator Guide Navigating to Wireless Settings Wireless Settings 802.11d Regulatory Domain Support Configuring 802.11d Regulatory Domain Support Mode Channel Configuring the Radio InterfaceConfiguring Internal LAN Wireless Settings Read-only field Configuring Guest Network Wireless Settings Security Understanding Security Issues on Wireless NetworksHow Do I Know Which Security Mode to Use? When to Use No Security Encryption Algorithm User AuthenticationKey Management Encryption Algorithms When to Use WPA/WPA2 Enterprise Radius How Does Station Isolation Protect the Network? Does Prohibiting the Broadcast of Ssid Enhance Security? Broadcast SSID, Station Isolation, and Security Mode Navigating to Security SettingsConfiguring Security Settings Static WEP None Professional Access Point Administrator Guide Key Type Transfer Key IndexKey Length Bits Open System Shared Key Both Authentication Algorithm Example of Using Static WEP Static WEP with Transfer KEY Indexes on Client Devices Ieee Radius IP Authentication ServerEnable Radius Accounting WPA/WPA2 Personal PSK Cipher Suites WPA Versions Key WPA/WPA2 Enterprise Radius Improving the security of the network Enable pre-authentication Enter the Radius IP Professional Access Point Administrator Guide Configuring a Guest Network on a Virtual LAN Guest LoginConfiguring Guest Access Using Virtual LANs DSL/T1 Using the Guest Network Configuring the Welcome Screen Captive Portal Configuring a Guest Network on a Dedicated Access Point Configuring Guest Access without Virtual LANs Navigating to Virtual Wireless Network Settings Virtual Wireless Networks Two Configuring VLANsVirtual Wireless Network One Ton Professional Access Point Administrator Guide Radio Understanding Radio Settings Status On/Off Navigating to Radio SettingsConfiguring Radio Settings Super G ModeIeee 802.11b Maximum Stations Broadcast a subset of its supported rate sets Rate Sets Professional Access Point Administrator Guide MAC Filtering Navigating to MAC Filtering Settings Filter Using MAC Filtering Stations List Professional Access Point Administrator Guide Specifying Limits for Utilization and Client Associations Load BalancingUnderstanding Load Balancing Load Balancing and QoS Navigating to Load Balancing SettingsConfiguring Load Balancing Tion Utilization for No New AssociationsUtilization for Disassociation Stations Threshold for Disassocia To apply your changes, click Update Settings 802.11e and WMM Standards Support Quality of ServiceUnderstanding QoS QoS and Load Balancing QoS Queues and Parameters to Coordinate Traffic Flow Professional Access Point Administrator Guide Random Backoff and Minimum / Maximum Contention Windows Configuring QoS Queues Navigating to QoS Settings Configuring AP Edca Parameters Enabling/Disabling Wi-Fi Multimedia Data 0 Voice Configuring Station Edca Parameters Transmission Opportunity Limit Txop Limit Professional Access Point Administrator Guide Using WDS to Bridge Distant Wired LANs Wireless Distribution SystemUnderstanding the Wireless Distribution System LAN Segment Backup Links and Unwanted Loops in WDS Bridges Security Considerations Related to WDS Bridges Navigating to WDS Settings Configuring WDS Settings Internal Network Local AddressRemote Address Bridge with WEP Key Example of Configuring a WDS LinkDisabled Local Address Professional Access Point Administrator Guide Time Protocol Navigating to Time Protocol Settings Enabling and Disabling a Network Time Protocol NTP Server NTP Server Professional Access Point Administrator Guide Understanding Snmp Snmp Navigating to Simple Network Management Protocol Read-write community name for per Enable SnmpRead-only Community Name entire Allow Snmp SET Requests Source hostname or subnet Configuring Your Network Management SystemRebooting and Upgrading Your Access Point Using Snmp Ftp//192.168.1.100/54531.1.24.tar Rebooting Your Access Point Using SnmpUpgrading your Access Point Ftp//testuser1testuser1@192.168.1.9922/54531.1.23.tar Professional Access Point Administrator Guide Reset Configuration Reboot Upgrade Professional Access Point Administrator Guide Navigating to Backup and Restore Settings Backup/Restore Restoring Access Point Settings to a Previous Configuration Backing up Configuration Setting for an Access Point Professional Access Point Administrator Guide Command Line Interface Professional Access Point Administrator Guide Basic Settings Yes Described in Backup/Restore on USR5453-AP login admin Password Enter help for help How to Access the CLI for an Access PointTelnet Connection to the Access Point USR5453-AP login Password Status Down SSH2 Connection to the Access PointTelnet Function Telnet Command Status USR5453-AP# Login as Set ssh Status Quick View of Commands and How to Get HelpCommands and Syntax SSH Function SSH Command Get bss wlan0bssInternal CommandGet log Get log-entry Add radius-user wally Command Description Remove radius-user wally Getting Help on Commands at the CLI Ready to Get Started? Command Usage and Configuration Examples Professional Access Point Administrator Guide Vlan1234 Understanding Interfaces as Presented in the CLIInterface Description Wlan0vwn1 Get interface vlan1234 role Saving Configuration ChangesGet interface vlanVLANID role Basic Setting Example Get Both the IP Address and MAC Address Get the MAC Address for an Access Point Wlan0wds1 Wds Down Wlan0wds2 Wlan0wds3 USR5453-AP# Get the Current Password Get the Firmware Version for the Access PointGet the Location of the Access Point Set the Location for an Access Point User Accounts Access Point and Cluster SettingsCluster Command Example Get MAC Addresses for all Access Points in the Cluster USR5453-AP#get radius-user all name name User Account Command ExampleGet All User Accounts USR5453-AP#add radius-user samantha username samantha USR5453-AP#set radius-user samantha password westportUSR5453-AP#set radius-user samantha disabled Add Users Larry samantha endora darren Status Command ExampleRemove a User Account USR5453-AP#remove radius-user wally USR5453-AP#get interface br0 Get Current Wireless Radio Settings Get Current Settings for the Ethernet Wired Guest Interface Priority Daemon USR5453-AP# get radio wlan0 detailGet Status on Events USR5453-AP# get log-entry USR5453-AP#set log relay-enabled USR5453-AP# get log USR5453-AP#set log relay-hostUSR5453-AP#set log relay-host myserver USR5453-AP#set log relay-port Get Client Associations Get neighbouring Access PointsGet Transmit / Receive Statistics USR5453-AP# get detected-ap USR5453-AP#get detected-ap Wired Interface Command Example Ethernet Wired Interface Get Summary View of Internal and Guest Interfaces Get Wired Internal Interface SettingsGet Wired Guest Interface Settings Set Up Guest Access USR5453-AP# get bss USR5453-AP#get interface brguest status downUSR5453-AP#remove bridge-port br0 interface eth0 USR5453-AP#get bridge-port br0 Name Interface USR5453-AP# get interface brguestUSR5453-AP#get interface brguest status up USR5453-AP#get bridge-port brguest USR5453-AP#get interface br0 detail Get/Change the Connection Type Dhcp or Static IPUSR5453-AP#get dhcp-client status up USR5453-AP#set dhcp-client status up USR5453-AP#get interface br0 static-mask Re-Configure Static IP Addressing ValuesUSR5453-AP#get interface br0 static-ip USR5453-AP#set interface br0 static-ip Security Wireless Interface USR5453-AP#get interface wlan0 security none Security Command ExampleGet the Current Security Mode Get Detailed Description of Current Security Settings Set the Broadcast Ssid Allow or Prohibit Enable / Disable Station Isolation USR5453-AP#set interface wlan0 security static-wep Set Security to NoneUSR5453-AP#set interface wlan0 security none Set Security to Static WEP USR5453-AP#set interface wlan0 wep-key-ascii yes Set bss wlan0bssInternal open-system-authentication onSet bss wlan0bssInternal shared-key-authentication off Set bss wlan0bssInternal shared-key-authentication on USR5453-AP#get interface wlan0 detail USR5453-AP#set bss wlan0bssInternal radius-ip Set Security to IeeeUSR5453-AP#set interface wlan0 security dot1x Radius Option Example USR5453-AP#get interface wlan0 security dot1x USR5453-AP#set bss wlan0bssInternal radius-key secretSet Bss USR5453-AP#set bss wlan0bssInternal radius-accounting off WPA Option Example Set Security to WPA/WPA2 Personal PSKUSR5453-AP#set interface wlan0 security wpa-personal Set bss wlan0bssInternal wpa-cipher-tkip off Cipher Suite Option ExampleSet bss wlan0bssInternal wpa-cipher-tkip on Set bss wlan0bssInternal wpa-cipher-ccmp off Set Security to WPA/WPA2 Enterprise Radius USR5453-AP#get interface wlan0 security wpa-personal USR5453-AP#set interface wlan0 security wpa-enterprise Enable Pre-Authentication USR5453-AP#set bss wlan0bssInternal radius-key KeepSecret Cipher Suite Option USR5453-AP#get interface wlan0 security wpa-enterprise USR5453-AP#set bss wlan0bssInternal radius-accounting on Set Guest Welcome Page Text Enable/Configure Guest Login WelcomeView Guest Login Settings Enable/Disable the Guest Welcome Set interface wlan0vwn1 security wpa-enterprise Configuring Multiple BSSIDs on Virtual Wireless NetworksReview Guest Login Settings Configuring Virtual Wireless Network One on Radio One Creating VWN Two on Radio One with WPA security Radio SettingsRadio Setting Command Example Get Ieee 802.11 Radio Mode Get Radio Channel Get Basic Radio SettingsGet All Radio Settings Get Basic Rate Set Configure Radio SettingsGet Supported Rate Set USR5453-AP#get supported-rate USR5453-AP#get bss wlan0bssInternal dtim-period USR5453-AP#set radio wlan0 mode gUSR5453-AP#set radio wlan0 beacon-interval USR5453-AP#set bss wlan0bssInternal dtim-period USR5453-AP#add supported-rate wlan0 rate USR5453-AP#set radio wlan0 fragmentation-thresholdUSR5453-AP#set radio wlan0 rts-threshold USR5453-AP#add basic-rate wlan0 rate USR5453-AP#get supported-rate wlan0 rate MAC Filtering Add MAC Addresses of Client Stations to the Filtering List Specify an Accept or Deny ListSet bss wlan0bssGuest mac-acl-name Guest USR5453-AP#get bss wlan0bssGuest mac-acl-mode accept-list Get Current MAC Filtering SettingsUSR5453-AP#remove mac-acl Guest mac Get bss interface mac-acl-mode Load Balancing Quality of ServiceQoS Command Enable/Disable Wi-Fi Multimedia QoS Command Example Data Access Point Station About Access Point and Station Edca ParametersUnderstanding the Queues for Access Point and Station Set Arbirtation Interframe Spaces Aifs Get QoS Settings on the Access PointGet QoS Settings on the Client Station USR5453-AP#get wme-queue USR5453-AP#set wme-queue wlan0 with queue vo to aifs Setting Minimum and Maximum Contention Windows cwmin, cwmaxSet wme-queue wlan0 with queue QueueName to aifs AIFSValue Set tx-queue wlan0 with queue QueueName to burst burstValue Set the Maximum Burst Length burst on the Access PointUSR5453-AP#set wme-queue wlan0 with queue vi cwmin 7 cwmax USR5453-AP#set wme-queue wlan0 with queue vo to txop-limit USR5453-AP#set tx-queue wlan0 with queue data2 to burst USR5453-AP#set interface wlan0wds0 remote-mac 00E0B8761B14 Wireless Distribution SystemConfiguring a WDS Link Getting Details on a WDS Configuration USR5453-AP#get ntp detail Time ProtocolSet ntp server ntp.instant802.com Keyboard Shortcuts and Tab Completion Help Reboot the Access PointReset the Access Point to Factory Defaults USR5453-AP#factory-reset Action on CLI Keyboard Shortcut Keyboard ShortcutsTab Completion and Help USR5453-AP#get system v USR5453-AP#get system version USR5453-AP# set mac-acl CLI Class and Field Overview Has name? \ # of instances? One Multiple Field Reference on CLI Class Relationships Class Description Class IndexAssociation Station AuthenticatedField Index Interface Bridge-port Basic-rate Priority BssPath-cost Beacon-interface StatusDescription Radio Ignore-broadcast-ssid MacDtim-period Max-stations Cluster-member Open-system-authenticationChannel-planner Cluster Debug ConfigDefault No-external-updates Field Description Detected-ap Capability Beacon-interval Type Last-beacon Dhcp-clientErp Beacons Dot11d Dot11Host Debug Static-domain Dns-12Domain Static-dns-12 Mask Interface Static-mask Rx-errorsType Static-ip Tx-packets Tx-errorsRx-compressed Rx-multicast Ip-route Gateway JvmKickstartd Log Time Log-entryDepth Number Server Mac-aclNtp Message Welcome-screen-text PortalWelcome-screen Max-bss Mode Tx-powerMax-bss Channel-policy Load-balance-disassociation-utilization WmewifinoacktestRts-threshold Fragmentation-threshold Ro-community Radius-userSerial Snmp Rw-community SshSupported-rate System Telnet PasswordEncrypted-password Password-initialized Queue Tx-queueCommunity Wme-queue Web-ui Possible Solution Professional Access Point Detection Utility does not find Cannot access the Web User Interface Access point My wireless device cannot find the wireless network Possible Solution Am experiencing poor wireless link quality Wireless Distribution System WDS Problems and Solutions Reboot or Reset Access Point Cluster Recovery Click Stop Clustering Stop Clustering and Reset Each Access Point in the Cluster Professional Access Point Administrator Guide Country Webmail Voice Support Information UAE Radio and Television Interference Declaration of ConformityDetachable Antenna Information FCC Radiation Exposure Statement UL Listing/CUL Listing For Canadian UsersIndustry Canada IC Declaration of Conformity CE Compliance EU Detachable Antenna Information Regulatory Channel FrequencyEU Health Protection Professional Access Point Administrator Guide Professional Access Point Administrator Guide Robotics Corporation Two 2 Year Limited Warranty Obtaining Warranty Service Limitations Disclaimer 802.3 802802.1x 802.2 802.11f 802.11b802.11d 802.11e AES Broadcast Address BeaconBridge Broadcast CSMA/CA BssidCcmp CGI DOM DCFDhcp DNS Ethernet EAPEdcf ESS Http FrameGateway Html Intrusion Detection Infrastructure ModeIbss Ieee Latency IPSecISP Jitter MAC LANLdap LLC OSI NATNIC NTP PID PacketPacket Loss PHY PSK PPP RTP RadiusRC4 Rssi STP SnmpSsid Tkip Supported Rate SetTCP TCP/IP Vlan UDPUnicast URL Wins WANWDS WEP XML WMM WPAWPA2 Wrap Index DCF Ieee Snmp WDS Index-328