FcShowNames, FcTxDisable port, FcTxEnable port | ADIC Scalar 1000

SNC 5100

0	0	0	0	ADIC 0338 00000060450d0080
8	2	3	0	OEM OEM	DCHS04X	6363	6820837B
9	2	4	0	OEM OEM	DCHS04X	6363	682076AC

value = 6 = 0x6 SN60023 >

fcShowNames

The fcShowNames command displays the node and port names (addresses) of the Fibre Channels.

Ctlr Id	Indicates the Channel Number for the interface
PCI Addr	The PCI address of the interface, showing bus,
	device id, and function number.
ISPType	The type of Fibre Channel Controller, ISP2300.
Node Name	The Fibre Channel node name for the SNC 5100.
Port Name	The Fibre Channel port name for the interface.

fcTxDisable [port]

The fcTxDisable command disables a Fibre Channel port transmitter.

Parameter	Value	Meaning


Port	1	The SNC 5100 connection labeled FC1

	2	The SNC 5100 connection labeled FC2

SN60023 > fcTxDisable 1 value = 0 = 0x0 SN60023 >

fcTxEnable [port]

The fcTxEnable command enables or re-enables a Fibre Channel port transmitter.

130 Commands

6-00020-02

Image 138

ADIC Scalar 1000, SNC 5100 manual FcShowNames, FcTxDisable port, FcTxEnable port

Contents

User Guide Copyright Notice Copyright Notice Europe Introduction Install the SNC Maintenance Action Plans Removal and Replacement Procedures Connecting to the Service Port Service Port Command ReferenceDiagnostic Command Reference Startup Message Reference Post Error CodesWarranty and Eula Glossary Safety Notices Safety InspectionWelcome Safety Label Remove AC PowerSafety Label Check External Machine Check Lithium Battery Fusing RequirementsLaser Safety Environmental Notices and Statements Regulatory Notices General RestrictionsUsage Restrictions Electronic Emission Statements Industry Canada Compliance Statement European Community Compliance Statement SNC CE Notice Documentation Configuration Overview Overview Configuration Support Address MappingInterface Protocol Awareness Fibre Channel Connections Hardware Product Description and FeaturesFibre Channel Interfaces Gbic speed Cable Type Distance Ultra2 Scsi I/O Interfaces Scsi Command Support Service PortEthernet LED Indicators LEDs Supported Platforms Scsi Operating Specifications Supported DevicesOperating Environment Power Consumption Power Requirements SNC Operating Specifications 00020-02 Pre-installation Procedure Pre-Installation ChecklistStep Actions Comments and References Installation Procedure Installation Checklist Installation Checklist See the setHost port,OS Host Utility Software Host Utility Software Attaching Scsi Devices Post-InstallationOther Installation Issues Maximum Number of LUNs Transfer Rates Ultra, Fast, and Asynchronous Wide and Narrow Scsi Buses Max Bus Endorsed Terminology Max. Bus Speed Lengths Table of Scsi Terminology and LimitationsScsi Trade Association Terminology MB/Sec Devices Problems on the Scsi Bus Scsi Bus Termination Excessive termination Bent pins in a Scsi connectorMissing terminator at the end of a Scsi bus Multiple devices at the same ID Inadequate cables Host Bus Adapter SetupFuses Mixed cable types Installing the SAN Explorer Installing the Host Registration ServicePower-Up and Boot Sequence Guidelines SNC SNC Other Installation Issues 00020-02 Maintenance Action Plans Troubleshooting Table Component Subsystem Go To Event Codes and Actions Check Event LogReview all visual observations and Event Codes against on Description Event Viewing Default Action2Event Codes and Actions Code Level1 Threshold Event Viewing Default Action Code Level Threshold Description Code Level1 Threshold LIP Event Codes and Actions Health Check Event Descriptions Heartbeat Event Descriptions Action Reference Table Action Reference TableAction Number Event Viewing Levels Event Code or Obvious SymptomStart MAP Event Viewing Levels Visually Inspect LEDs Check Host Versions Check for Problems on Attached DevicesCheck SNC 5100 Product Versions Adic Management Console version Firmware version Hardware version Stop all I/O Remove the Ethernet cable if installed Quick Component CheckPerform Health Check Database Full MAP Check the Host Event Log Device Access MAP Check Fibre Channel Port Status Check Scsi Channel Devices Check Channel Zoning Settings Scsi Channel MAPGet Scsi Information for the SNC Check Attached Scsi Devices from the Service Port Compare Listed versus Physical Devices Compare Listed versus Supported Devices Check Scsi Bus Termination Check for Multiple Scsi IDs Type Improper Device Type Examine Scsi Cables Examine Scsi Connectors Scsi Health Check Scsi Loop Back Test Testing Scsi Cables Isolating Scsi devices Restore Scsi Setup Fibre Channel MAP Verify Fibre Channel Connections Test Gbic Examine Cables Fibre Channel Loop Back Test Testing Fibre Channel Optical Cable Replace Fibre Channel Cable Replace Fibre Channel Device Temperature MAP MAP for the SNCObserve Operational LED Behavior Notification of Problems in Temperature Subsystem Temperature Warnings or Alarms Received Power MAP Fan Speed is in Warning or Alarm Range Ethernet MAP Ethernet Port on Faceplate SNC Example SN60023 ifShow SNC Display of failed Ping test Step From the service terminal, enter the diagBoot commandFrom the service port, enter the elTest command Verify that the diagmode prompt is displayed Service Port MAP If both addresses are the same, go to step Check Connection with Boot Messages Check the RS-232 Cable Virtual Private SAN Scalar Firewall Manager Settings MAP Check Scalar Firewall Manager Access SettingsPerform these steps if SFM devices are unavailable Verify Host Access to Devices SNC Page Removal and Replacement Procedures Handling Electrostatic Discharge-Sensitive Parts Removing the Gbic Removing and Replacing the GbicBefore Removing or Replacing the Unit Replacing the Gbic Removing and Replacing the Unit Removing the SNC Final Diagnostic Tests Replacing the SNCFinal Test Preparation Fibre Channel Tests Test Fibre Channel Port Ethernet Test Test Scsi Port 1Test Scsi Port 3 Network Setup for the SNC For more information, see Network Setup for the SNC For more information, see the hostNameSet command on , Pre-Installation Checklist, onEnter the hostNameSet command to set the Host name Ethernet Port Foster ethAddrSet 10.0.0.2 Checklist Updating the SNC Post-Repair Checklist Post-Repair Checklist Start the Adic FcShowDevs SNC Post-Repair Checklist 00020-02 Service Port Connections DB-9 RS-232 Connector Pin Assignments Lists the null modem cable connections Connecting the Service TerminalHardware Required Null Modem Cable Connections Initial Setup of HyperTerminal Verifying the Connection Updating Firmware and Configurations Updating SNC 5100 Firmware Saving a Configuration File Loading a Configuration File Zmodem Status Code Table Zmodem Status CodesStatus Description Code Setting the Time and Date Setting the Real Time Clock For more information, see the tzSet timezone command on Adding a Host System Running Timeserver For more information, see the setTimeHost command on Disabling the Timeserver Host For more information, see the rtcSetCurrent command on Synchronizing the Real Time Clock with a Timeserver Command or Command Description Group Command and Control CommandsCommands Listed Alphabetically byFunction Managing the SNC Environmental Sensors Command or Command Description GroupDiagnostics Ethernet Network Event Logging Fibre Channel Flash File System Health CheckHelp Product Data Scalar Firewall Manager Scsi Startup ArptabShow ClearReservationdevIdParameter Value CleShowAll CleHelpCleShow LUN CsClearLogFile DateSetFromRTC DiagBootDiagHelp command displays a list of the diagnostic commands DiagHelp DisableCC option number Option EnableCC EnvMonShowChannel Name Description EnvMonRangeShow EthAddrGet EthAddrSet FcConnTypeGet portParameter Value Meaning FcConnTypeSet port,connection FcFibreSpeedGet port FcFibreSpeedSet port,speed FcGbicShow port GBIC. Specifying the port number is optional Finisar Corp Value Port Mode FcPortModeGet port FcPortModeSet port,mode FcRestart port FcShow level Level Meaning Ctlr Id FcShowDevs Ext. Fifo FcTxDisable port FcTxEnable portFcShowNames GateAddrGet GateAddrSet Help command displays a list of the shell commands TerminalHelp Commands 133 00020-02 HlthChkHelp HlthChkIntervalGetHlthChkIntervalSet HlthChkNow HlthChkLevelGetHlthChkLevelSet Host add,hostname,ipAddress Following is an example of host file contents WhereHost delete,hostname Host list HostTypeShow HostNameSetHostShow IcmpstatShow IfShow InetstatShow InitializeBox IpstatShow LicenseShowLoggerDump number File are displayed starting with the most recent events SN600393LoggerDumpCurrent level Ls or ll MacShow Ethernet interface MapCompressDatabase MapHelp MapRebuildDatabase MapShowDatabase MapShowDevs SNA MapWinnowDatabase MapWinnowDatabaseLun dev IDMbufShow Administrator NetHelp NormalBoot Rdate timeserver ReserveShow level RebootReset ReserveShow Viewing Levels RestartScsi channel Ridtag valueOn original equipment, the RID tag will be blank Route Route add,destination,gateway Route list command lists the existing routes Route delete,destination,gatewayRoute list String RtcSetCurrent ScsiAltIdGet channel ScsiAltIdSet channel,id ScsiHostChanGet channel ScsiHostChanSet channel,mode ScsiHostIdGet channel ScsiHostIdSet channel,idScsiRescan channel ScsiResetDisableGet channel ScsiResetDisableSet channel,mode ScsiShow LUN ScsiTermGet channel ScsiTermSet channel,terminationSetFcFrameSize channel,size SetFcHardId channel,id SetHost port,OS SetNettime value Value Meaning SfmAccessApply SetSnaCCLun newLUNSetTimeHost Access Value SfmAccessClear disable codeSfmAccessSet hostindex,Starting LUN,Ending LUN,Access SfmActiveSet If SFM is already active, the following is displayed SfmFeatureEnable license key stringFollowing command example shows SFM information for host Id SfmConnectionSet hostindex,host connection string SfmInactiveSet If SFM is already inactive, the following is displayedSfmNameSet hostindex,name string SfmShow hostIndex Hostindex Meaning SfmSparseAccessSethostindex,LUN string,Access SfmTypeSet hostIndex,OS type stringShellLock ShowBox ShowVersions SncFeatureEnable licensekeystring SnmpCommunitiesShow SnmpHelp command displays a list of the snmp commands SnmpHelp SnmpTrapCommunitySet string,view SnmpReadCommunityAdd string ,viewSnmpReadCommunityRemove string SnmpWriteCommunityAdd string,view SysConfigShow SysNodeNameModeSet ModeSnmpWriteCommunityRemove string Mode Definition SysNodeNameModeShowSysVpdShow or sysVpdShowAll OEM Adic Data for the Fibre Channel Gbic IBM Gbic NV RAM CPU Sz filename Targets TcpstatShow TrapDestAdd ipAddress TrapDestRemove ipAddress TrapDestShow TzSet timezoneUdpstatShow Uptime UserAdd username,passwordUserDelete username,password User UserHelp UserHelp command displays a list of the user commandsUserList Version SNC Boot Modes Entering Diagnostic Mode Health Check Special ProceduresRestoring Normal Mode Manual Health Check Retrieving the Code 43 Dump File Event Log Dump SNC Boot Mode Commands Diagnostic Commands ElTest FcSlotTest ScsiChannelTest x,y Unsuccessful Fibre Test Unsuccessful Scsi Test cable not plugged ShowBox also lists the cabling requirements for each slot SupportDump EnvMonShow dmva reserveShow Post Boot Behavior ROM Init Simple Access Test Initial Post Bitwalk Test Memory SizePattern Test Identify and Execute bootrom Secondary PostAddress Test Post Service Menu Start of Bootrom Button may be depressed any time during the memory tests Cold boot from Alternate bootromCold Boot from primary bootrom After completing the memory tests Post will display Error Displays Receive new boot image from serial portFull Version information SNC Post Service Menu 00020-02 Bootrom Messages See the sample code below LIC Initialization Messages Final Startup Messages SNC Bootrom Messages 00020-02 Basic Input/Output System Dynamic Random Access MemoryMaintenance Action Plan Differential Ended Synchronous Dynamic Random Access Memory Power-On Self testReplacement Identification SAN Replication Services Warranty and Eula Adic Limited Product Warranty Adic Limited Product Warranty 00020-02 Adic End User License Agreement Adic End User License Agreement 00020-02 Adic End User License Agreement 215 00020-02 SNC Bootrom 110, 171 Index Post MAP SNC 220 00020-02