Verifying Site Requirements | Nortel Networks AN/DC specification

Installing the ANH-8/DC

Verifying Site Requirements

Verify that your installation meet the requirements listed in this section.

•Space Requirements

•Electrical Requirements

•Environmental Requirements

Note: The AN/DC should be installed only in dedicated equipment rooms where access is limited to qualified service personnel.

Space Requirements

The installation site must provide a certain amount of free space around the ANH-8/DC to dissipate heat. Install the ANH-8/DC in a space that meets these specifications:

•Width: 19.25 in. (48.9 cm)

•Minimum depth: 17.25 in. (43.8 cm)

•Depth for servicing: 26.25 in. (66.7 cm)

Electrical Requirements

The installation site must provide an isolated power source that meets these electrical specifications:

•Input voltage of -48.0 or -60.0 volts DC

•1.5 amperes (A) input current under full load at -38.0 VDC input

•Reinforced insulation from the main AC power

We recommend the use of #16 AWG cables between the AN/DC and the power source to minimize voltage drop. When measuring the cable run, be certain to include both the input and return cables.

312410-A Rev 00

2-5

Image 47

Nortel Networks AN/DC manual Verifying Site Requirements

Contents

Installing and Operating AN/DC and ANH-8/DC Systems USA Requirements Only Copyright 2000 Nortel NetworksTrademarks Statement of Conditions Canada Requirements Only Japan/Nippon Requirements OnlyTaiwan Requirements Canada CS-03 -- Règles et règlements FCC Part 68 Compliance Statement Nortel Networks NA Inc. Software License Agreement Vii Page Contents Chapter Installing the ANH-8/DC Chapter Starting the AN/DC and ANH-8/DC Appendix B Using Local Boot the Quick-Start Procedure Figures 10. Verifying Directed Netboot Configuration Tables Table D-7 Before You Begin Preface Text Conventions This guide uses the following acronyms Acronyms Ieee Technical Solutions Center Telephone Hard-Copy Technical Manuals How to Get HelpPage Verifying Shipment Contents Chapter Installing the AN/DCPreparing for Installation Mounting Hardware Cables Supplying Tools and EquipmentTools Mounting Hardware Service ConsoleVerifying Site Requirements Environmental Requirements Space RequirementsElectrical Requirements Positioning the AN/DC on a Flat Surface Installing the AN/DCInstalling the AN/DC in a Rack Tighten each cagenut screw with a Phillips screwdriver Installing the AN/DC in a Rack Mounting the AN/DC on a Wall Mounting the AN/DC on a Wall Plugging Cables into the AN/DC Connecting Communications Cables Connecting a Terminal Console Connecting a Management Console or Modem Parameter Value Console Parameters Connecting a Terminal Console Connecting a PC Console Power Source Modem Parameters Connecting a ModemModem Signal/Parameter Value Modem Parameters 11. AN/DC Power Switch and DC Terminals Connecting to the DC Power Source 12. Attaching AN/DC Power Input Cables If connecting to the grounding stud, use a #6 ring terminal Chapter Installing the ANH-8/DC Inspect all items for shipping damage Accessories in the ANH-8/DC Shipping Container Sample Cagenuts and Screws for Unthreaded Rack Rails Verifying Site Requirements Positioning the ANH-8/DC on a Flat Surface Installing the ANH-8/DC Installing the ANH-8/DC in a Rack Attaching Flange Brackets to Rack-Mount the ANH-8/DC Installing the ANH-8/DC in an Electronic Enclosure Rack Attaching Flange Brackets to Wall-Mount the ANH-8/DC Mounting the ANH-8/DC on a Wall Mounting the ANH-8/DC on a Wall Connecting an AUI Cable Connecting an AUI Cable Using the MDI/MDI-X Switch Connecting Ethernet Repeater Port UTP Cables ANH-8/DC Front-Panel MDI-X/MDI Switch Connecting the ANH-8/DC to Other Repeaters/Hubs 10. Linking ANH-8/DC Systems 11. Linking Hubs 12. Connecting a Second Ethernet Interface Cable Connecting a Second Ethernet Interface UTP Cable 13. Connecting Synchronous Cables to COM1, COM2, or COM3 Connecting Synchronous Cables 14. Connecting an Isdn BRI Cable Connecting an Isdn Cable Connecting a Management Console or Modem 15. Attaching the Null Modem Adapter Console is now connected to the ANH-8/DC 17. Connecting a PC Console to the ANH-8/DC Complete the following steps 18. Connecting a Modem to the ANH-8/DC To connect the ANH-8/DC to the power source 20. Attaching the ANH-8/DC Power Input Cables 21. Attaching the ANH-8/DC Earth Ground Cable Chapter Starting the AN/DC and ANH-8/DC About Software Installation Summary of Initial Startup Options Boot Options Flash Memory Card Installing the Flash Memory Card Gently push the card until it fits snugly into place Using EZ Install Logging In to the Diagnostic Monitor Using Netboot, Directed Netboot, or Local Boot Running Diagnostics Manager Logging In to the Diagnostic Monitor Getcfg Continuing with NetbootIfconfig Andiag ifconfig xcvr1 192.32.37.125 Reset Verifying the Interface Configuration Netboot Specifying the Source for Directed Netboot Continuing with Directed Netboot 10. Verifying Directed Netboot Configuration 11. Directed Netboot Bconfig config local Continuing with Local Boot 12. Local Boot Run install.bat Logout Chapter Operating the AN/DC and ANH-8/DC AN/DC Front-Panel LEDs Ensuring a Successful Installation Operating the AN/DC and ANH-8/DC Meaning AN/DC LED DescriptionsFront-Panel LEDs Front-Panel LEDs Synchronous interfaces COM1 and COM2 Back-Panel LEDsBack-Panel LEDs Meaning Ethernet/Second Ethernet interface Xcvr or UTP LED Label Color Meaning ANH-8/DC LED Descriptions ANH-8/DC Front-Panel LEDs Color Meaning Ethernet UTP2 interface Powering On and Off AN/DC Power Switch Resetting the AN/DC or ANH-8/DC ANH-8/DC Reset Switch AN/DC Reset Switch AN/DC Flash Memory Card Eject Button Removing a Flash Memory Card Protecting Memory Card Files 10. Memory Card Read-Write Protect Switch Installing and Operating AN/DC and ANH-8/DC Systems Using the ifconfig Command Appendix a Configuring Netboot and Directed Netboot Fr -annexd -annexa -lmi -intclk Configuring a Synchronous IP Interface for Netbooting Intclk Configuring an Ethernet Interface for Netbooting Ifconfig -disable interface ifconfig -enable interface Enabling and Disabling Interfaces with ifconfigUsing the bconfig Command Table A-3 Bconfig Command Options Installing and Operating AN/DC and ANH-8/DC Systems Appendix B Using Local Boot the Quick-Start Procedure Fill out the Global Information Worksheet completely Filling Out the Quick-Start Worksheets Step Requested Information Options Your Response Global Information WorksheetGlobal Information Worksheet Enter the IP address for the COM Requested Information Options Your Response Router Protocol WorksheetsRIP Worksheet Ospf Worksheet Broadcast Ospf Worksheet Requested Information Options Your Information Static Route to Site Manager Worksheet Frame Relay Worksheet Wide Area Protocol WorksheetsNortel Networks Proprietary PPP Worksheet PPP Standard Worksheet PPP Standard Worksheet To Do the Following Action Details Using the Quick-Start CommandsTable B-1 Quick-Start Commands Smds Worksheet Running the Quick-Start Script Installing and Operating AN/DC and ANH-8/DC Systems ANH-8/DC Physical Specifications Appendix C Technical SpecificationsAN/DC Physical Specifications AN/DC Hardware Communications Options Power Supply Specifications Network Interface Description Table C-1 AN/DC Network Interfaces ANH-8/DC Hardware Communications Options Table C-2 ANH-8/DC Network Interfaces Connector Pinouts Table C-3 Pin Assignment Pin No Signal NameAttachment Unit Interface AUI Ports AUI Port Pin Assignments Table C-4 RJ-45 Jacks Pin Assignments 10Base-T Repeater Ports ANH-8/DC only Synchronous Interfaces Table C-5 Synchronous Port Pin Assignments Pin Assignment Pin No. Signal Name Local Console Connections Table C-6. Isdn Connector PinoutsPin Assignment Pin No Signal Isdn BRI Ports Pin Assignment Pin No Signal Name Direction Table C-7. Service Console Port DB-9 Pin Assignments Installing and Operating AN/DC and ANH-8/DC Systems 28, X.21 TNV at Selv levels ANH-8/DC Safety StatusAppendix D Requirements for European Operation Port Location Port Description Type of Circuit Table D-5 Safety Status Order Nos , 50025, and 24001-S AN/DC Safety StatusSafety Status Third Synchronous Interface Module Table D-6 Nortel Networks Termination Remote Termination Pin SignalSynchronous Cabling Requirements WAN Interface Order No Table D-6 WAN Interface Order No Table D-7 Interface Order No Local Wire Connections Pin 41 Pin 28 Pin 14 Voltage Power RequirementsTable D-9. Isdn BRI Power Requirements Isdn BRI Requirements Figure D-4. Isdn BRI Clearances and Creepage Distances Isdn BRI Clearances and Creepage Distances Clearance Creepage Y Host or expansion card Isdn BRI Upgrade Module Safety StatusTable D-10 Isdn BRI Clearances and Creepage Distances Voltage used or generated by other parts Pin Signal Isdn BRI Connector PinoutsTable D-12 Isdn Connector Pinouts Numbers Index Index-2 Index-3 Index-4 Index-5 Index-6