![](/images/new-backgrounds/1125774/125774233x1.webp)
4. Set value recording sheet
Memorize set values in the column of "Set value" for efficient servicing when the memory trouble occurs and the EEPROm is replaced. Make a copy of this sheet and use with the service sheet.
Purpose/kind | Section |
|
|
| Contents | |
|
|
|
|
| ||
|
| Main code | Sub code | Set value | Description | |
|
|
|
|
|
|
|
| Paper feed section | 51 | 02 |
| Adjustment value of contact pressure of the paper on the main | |
|
|
|
| body resist roller | ||
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| 50 | 01 |
| Copy paper lead edge void amount adjustment | |
|
|
|
|
| (Resist adjustment A) | |
|
|
|
|
|
|
|
|
|
|
|
| Copy paper lead edge void amount adjustment | |
|
|
|
|
| (Resist adjustment B) | |
|
|
|
|
|
|
|
|
|
|
|
| Copy paper lead edge void amount adjustment | |
|
|
|
|
| (Lead edge void adjustment ) | |
|
|
|
|
|
|
|
|
|
|
|
| Copy paper lead edge void amount adjustment | |
|
|
|
|
| (Rear edge void adjustment) | |
|
|
|
|
|
| |
|
| 46 | 01 |
| Adjustment value of copy density (exposure level) in each copy | |
|
|
|
|
| mode and of copy density gradient (exposure gradient) | |
|
|
|
|
|
|
|
|
|
|
|
| Manual copy mode density level 1 | |
Adjustment |
|
|
|
|
|
|
Optical unit |
|
|
| Manual copy mode density level 5 | ||
|
|
|
| |||
|
|
|
|
|
| |
|
|
|
|
| Manual copy mode density level 1 (Toner save mode) | |
|
|
|
|
|
|
|
|
|
|
|
| Manual copy mode density level 5 (Toner save mode) | |
|
|
|
|
|
|
|
|
|
|
|
| Auto copy mode density level 1 (Not toner save mode) | |
|
|
|
|
|
|
|
|
|
|
|
| Auto copy mode density level 5 (Not toner save mode) | |
|
|
|
|
|
|
|
|
|
|
|
| Auto copy mode density level 1 (Toner save mode) | |
|
|
|
|
|
|
|
|
|
|
|
| Auto copy mode density level 5 (Toner save mode) | |
|
|
|
|
|
| |
|
|
|
|
| Photo copy mode density level 1 (Not toner save mode) | |
|
|
|
|
|
|
|
|
|
|
|
| Photo copy mode density level 5 (Not toner save mode) | |
|
|
|
|
|
| |
|
| 47 |
|
| The AE sensor and the optical section characteristics memory | |
|
|
|
|
| data for the change in the copy lamp application voltage | |
|
|
|
|
|
| |
|
| 48 | 01 |
| The vertical copy magnification ratio adjustment value | |
|
|
|
|
|
| |
|
|
| 02 |
| The horizontal copy magnification ratio adjustment value (when | |
|
|
|
|
| the document table is used) | |
|
|
|
|
|
| |
| Developing unit | 25 | 02 |
| Toner density initial set value | |
|
|
|
|
|
| |
| Specifications | 26 | 06 |
| Destination specifications | |
|
|
|
|
|
| |
Setting | Fuser unit | 26 | 13 |
| Setting of the main motor operation mode in warming up | |
|
|
|
|
| ||
43 | 01 |
| The set value of fusing temperature | |||
|
|
| ||||
|
|
|
|
|
| |
| Maintenance counter | 21 | 01 |
| Setting of the maintenance cycle | |
|
|
|
|
|
| |
|
| 22 | 06 |
| The developer count of the installed developer unit can be | |
Counter | Developing unit |
|
|
| checked. | |
|
|
|
|
| ||
| 07 |
| The developer replacement cycle of the installed developer unit | |||
|
|
|
| |||
|
|
|
|
| can be checked. | |
|
|
|
|
|
|
|
10 – 3