Rf In/Out, SA Trig Output | Agilent Technologies E8285A instruction

Chapter 2, Description of Connectors

Connectors

RF IN/OUT

The RF IN/OUT port allows full-duplex interaction, or the RF IN portion can be used with the DUPLEX OUT port, which provides increased output power.

Operating Considerations

When testing CDMA mobile stations, it is important to enter an RF Level Offset for the selected input and output ports. Refer to “Calibrating the Test Set” chapter in the Agilent Technologies E8285A Application Guide.

•Type-N

•This port must be used when measuring transmitter (RF) power.

•This port can be selected in the CONFIGURE, CDMA REVERSE CHANNEL SPECTRUM, analog TX TEST, DUPLEX TEST, RF ANALYZER, or SPECTRUM ANALYZER screens.

•Signals ≤ 60 mW can be input to the ANT IN connector for all RF measurements except transmitter power.

Over-Power Damage. Refer to the Test Set's front panel for maximum input power level. Exceeding this level can cause permanent instrument damage.

CAUTION:If the RF power at the RF IN/OUT port exceeds allowable limits, a loud warning signal sounds and a message appears at the top of the screen.

If this occurs, disconnect the RF power, press the Meas reset key, and allow the Test Set to cool off for approximately 2 minutes before making any other measurements on this port.

SA TRIG OUTPUT

This connector provides a trigger signal for measuring a mobile station’s time response to open loop power control using an external spectrum analyzer.

Test Sets with firmware revisions A.04.50 and higher include a measurement that automatically triggers a power versus time measurement at the correct time relative to the Test Set’s output level change and displays a graph showing the mobile station’s time response to open loop power control. See "Measuring Time Response of Open Loop Power Control" in chapter 5 in the Application Guide.

Operating Considerations

•BNC

•Trigger occurs 180 microseconds before the RF power changes

•Trigger rise time is negligible (approximately 600 ns).

76

S:\agilent\e8285\REFGUIDE\MANUAL\connectr.chp

Image 76

Agilent Technologies E8285A manual Rf In/Out, SA Trig Output

Contents

Reference Guide Copyright License under the clause at Dfars 52.227-7013 APR Manufacturer’s Declaration Herstellerbescheinigung General Safety Considerations for this Instrument Product Markings Mobile Station Test Set Duration of Warranty 1 year E8285A Cdma \agilent\e8285\REFGUIDE\MANUAL\frntmt.fb Declaration of Conformity Agilent Technologies E8285A Support Contacts Regional Sales and Service Offices Testing Testing and for analog testingThis Book Technologies E8285A Documentation Map Specifications 5968-8839E Instrument Basic User’s Handbook E2083-90000 Contents 101 100102 104 105106 108 144 148 Cmax Dsat ESN Contents MS FER Rand Randu SID MSB System ID 418 System Type Call Control Contents Description of Keys Keys are listed in alphabetical order Agilent Technologies E8285A Front Panel Keys AddressAnswer This sets the Test Set’s Gpib address to Assign AverageSee Also Programming Average Output 714MEASAFRDISTNAVERSTAT on Call/Page CancelEEX Ibasic reset End/ReleaseEnter Hold This queries the increment value for the RF Gen Freq field Increment ÷10, Increment set, IncrementProgramming Increment set Output 714RFGFREQINCRMODE LOG Increment value from 10 MHz to 1 MHz FrequencyProgramming Increment÷10 Programming Increment ×10 K1 K5, & K1’- K3’Cannot be changed Puts the device at address 14 in local mode LocalLow limit, High limit Programming Local Output 714MEASAFRDISTNHLIMSTAT? Used to display the high and low measurement limit values Analyzer FM deviation measurementDeviation measurement HLIMitEXCeeded? and LLIMitEXCeeded? commands to detect if a YESViation measurement have been exceeded To Detect If a Measurement Limit Has Been Exceeded. Use This resets all of the active measurements in the Test Set Meas resetProgramming Meas reset Programming Meter MeterTo Turn the Meter on and OFF To Set the Number of Intervals on the Meter To Query the State of the MeterTo Query the Number of Intervals on the Meter Endpoint to 10 watts for the TX power measurement Meter for the TX power measurementGraph meter high endpoint and low endpoint To Set the Meter High End and Low End Points To Set the Meter High End and Low End Point Display Units Graph meter for the TX power measurement to dBmTo Query the Meter High End and Low End Point Display Units Power PresetNo Ratio W On/Off This recalls the instrument state saved in the file SETUP1 See Also Print Configure Screen onPrint Recall Ref set Programming Ref set Commands to query a measurement reference point Set a measurement reference point Measurement to dBm This saves the instrument state to a file named SETUP1 RegisterRelease Save Shift Yes On/Off To 9, decimal point ., +/-, and a to F Symbol Keys BackspaceDown-Arrow, Up-Arrow E8285A User’s Guide Units-of-Measure Keys Front Panel Knobs Miscellaneous HardwareCursor Control Knob Programmable Front-Panel Keys for Screens Key Name Screen Displayed Gpib Example Non-Programmable Front-Panel Keys and Functions Guidelines for Using Measurement Data Functions Data Functions Keys Guidelines for Using Numeric Entry Field Data Functions User Keys Description of Connectors Connectors are listed in alphabetical order Description of Connectors Agilent Technologies E8285A Rear Panel Antenna ConnectorsOperating Considerations Audio in LOW, High Audio output is used to output signals from AF Generators 1 Audio OUTAUD Monitor Output See Also Scope To field description, on Cell SITE/TRIGGERS Cdma Clock MUX Output Composite Video Even SEC Input Duplex OUTSee Also Cdma Clock MUX Output field description, on Gpib EXT REF InputSee Also Gpib Adrs field description, on Modulation Input Pin assignments for this connector are as followsPaging Channel Logging DCS2 Parallel Port Protocol Serial RF IN/OUT SA Trig Output Serial Port Serial Port 16X Chip Output Traffic Channel Logging DCS1See Also Cell SITE/TRIGGERS on MHz Output See Also EXT REF Input on Description of Screens These screens are listed in alphabetical order Adjacent Channel Power Screen Adjacent Channel Power Screen How the Test Set Measures Adjacent Channel Power ACP AF Analyzer Screen AF Analyzer Block Diagram onAF Analyzer Screen AF Analyzer Block Diagram AF Analyzer Functional Block Diagram Call Control Screens Call Control Screen Call Control Screens Analog Meas Analog Meas Screen Requirements for Using The Analog Meas Screen How To Program The Analog Meas Screen Call Control Screens Authentication Authentication Screen Call Control Screens Call BIT Call BIT Screen Using the Call BIT Screen General Syntax Example of Querying a Single Field Call BIT Screen Signaling Message NamesExample Printout General Syntax’ Printed Test Set Response MessageExample of Modifying Multiple Fields With One Output Call Control Screens Call Configure Call Configure Screen Call Control Screens Call Data Call Data Screen Messages which can be viewed are Reading the Call Data Screen Message Fields Aword Querying a Single Field Example of Querying a Single Field Querying Multiple Fields With Single OUTPUT/ENTER Cdma Authentication Screen Cdma Authentication Screen Cdma Call Control Screen Cdma Call Control Screen Cdma Cell Site Configuration Screen Cdma Cell Site Configuration Screen Cdma Cellular Mobile Receiver Test Screen Cdma Cellular Mobile Receiver Block Diagram onCdma Cellular Mobile Receiver Test Screen Cdma Cellular Mobile Receiver Block Diagram OUT Cdma Cellular Mobile Transmitter Test Screen Cdma Cellular Mobile Transmitter Test Screen Cdma Gated Power Screen Cdma Gated Power Screen Cdma Generator Control Screen Cdma Generator Control Block Diagram onCdma Generator Control Screen Cdma Generator Control Block Diagram Lator Cdma Mobile Reported FER Screen Cdma Mobile Reported FER Screen Cdma Mobile Reported Pilot Strength Screen Cdma Mobile Reported Pilot Strength Screen Cdma Open Loop Time Response Screen Cdma Open Loop Time Response Order Screen Cdma Reverse Channel Spectrum Screen Cdma Reverse Channel Spectrum Screen Cdma Short Message Service Screen Cdma Short Message Service Screen Cdma Swept Power Measurement Screen Cdma Swept Power Measurement Screen Cdma Transmitter Power Range Test Screen Cdma Transmitter Power Range Screen Configure Screen Configure Screen Duplex Test Screen Duplex Test Block Diagram onDuplex Test Screen Duplex Test Block Diagram Duplex Test Functional Block Diagram Help Screens I/O Configure Screen Message Screen Oscilloscope Screens Oscilloscope Screen and Menus Using the Scope To Field Oscilloscope Input IndicatorSelecting the Oscilloscope’s Input Print Configure Screen Printer Configurations Screen RF Analyzer Screen RF Analyzer Block Diagram onRF Analyzer Screen RF Analyzer Block Diagram RF Analyzer Functional Block diagram RF Generator Screen RF Generator Block Diagram onRF Generator Screen RF Generator Functional Block Diagram 2II RX Test Screen RX Test Block Diagram onRX Test Screen RX Test Block Diagram RX Test Fields and Their Functions Service Screen Select Service from the To Screen menu Menus are accessed using the Controls field To access the functions without having to change menusSpectrum Analyzer Screens Spectrum Analyzer Screen and Menus Setting Resolution Bandwidth and Sweep Rate Using the Spectrum AnalyzerAutomatic Calibration Description of the Tests Subsystem Tests ScreensTests Main Menu Screen Or SET UP Test SET lists Tests Main Menu This screen displays the channel frequencies to be tested Tests Channel InformationTests Channel Information Screen Tests Test Parameters Tests Test Parameters Screen Tests Order of Tests Tests Order of Tests Screen Tests Pass/Fail Limits Tests Pass/Fail Limits Screen Tests Save/Delete Procedure Tests Save/Delete Procedure Screen Tests Executions Conditions Tests Execution Conditions Screen Tests External Devices Tests External Devices Screen Tests Printer Setup screen determines how tests are run Tests Printer SetupTests Printer Setup Screen Tests Ibasic Controller Tests Ibasic Controller Screen TX Test Screen TX Test Block Diagram onTX Test Screen TX Test Block Diagram TX Test Functional Block Diagram 146 Description of Fields Field descriptions are listed in alphabetical order Access annunciator Screens Where Field is PresentFields Abort Print Avg Power Selects the Access Probe Power measurementAcc Prb Pwr Acc Prb Pwr 150 Access Probe annunciator AC Level Active Active annunciator ACP MeasTurned on Base station is not active Add Intcpt AddrEnters 8 in the Add Intcpt field Tests External Devices AF Anl AF Cnt Gate AF Freq AFGen1 Freq AFGen1 Lvl AFGen2 Freq AFGen1 ToThis field has two fields AFGen2 To Entering an Akey Directly into the Test Set AKeyGenerating a New Akey Key Digits Enters a 1 preceded by 19 0’s in the A-Key field Alert All Chans?This field sets the Alert parameter in SMS messages Sets the Alert parameter to On Alt Pwr Ms Cal Bands Selects All Bands in the Alt Pwr Ms Cal Bands field Queries the Cdma amplitude error measurement result Ampl ErrorAM Depth See Also Atten Hold on Screens Where Field is Present Amplitude Amplitude Cdma Swept Power Measurement Answer ModeSelects manual mode Sets the trigger amplitude Sets the remote operation trigger mode to Single AntennaArm Triggers all active measurements Disarm field description, on Screens Where Field is Present Queries the Cdma gated power attack timeAttack Time Atten Hold This field sets the Audio in LO connector’s stateAudio In Lo Turns Authentication On Authentication Tests, E8285A Application GuideAudio Out Authen Authentication Data Table Clears the Authentication Data TableQueries the Cdma Authentication Data Table Authen Data Clear Reading the Authentication Data Table over Gpib Data Position Numeric Value 173 Programming Example for Authentication Data Table END Select 175 Auto/Norm AuthentThis field specifies how the trigger level is set Auto Zero Autostart Test Procedure on Power-UpTests Execution Conditions Operating Considerations for the Average Power Measurement Avg PowerAverages Queries the average power measurement Selects the average power measurementZeroes the average power measurement See Also Chan Power on Awgn Sets the Awgn generator’s level to −75 dBm Sets the Bandclass parameter to Band ClassIf Bandclass 1 or 4 is selected Base Frequency is calculated using the following formula Base Freq User Defined Beeper Base IDParameters Message from the Test Set BER Thresh Queries the Cdma gated power burst time Burst Time By # errors This field is coupled to the Span field’s settingBW= Range of Values By # frames Called Number This field is used for measuring access probe power levels Calling NameCall Limit Limits call progress to the paging channel Call Status Cdma Status Register Bit DefinitionsRegistering annunciator on 360 Carrier Ref CarrierQueries the carrier feedthrough measurement result CC Order Center Freq Analog Selects n up power control steps Center Freq CdmaChange Sets the center frequency to 850 MHz Chan Chan is divided into two fields Channel Cdma to Analog or Interband Handoffs Sets the Channel field to Channel BW Selects Channel Power measurements Chan PowerQueries the channel power measurement Operating Considerations for the Channel Power Measurement Chan Power Meas IntrvlSets the measurement interval to 1 ms Check Chan StdTests Pass/Fail Limits Timer Reg field on Check DigitsMS Database field on Register Cdma field on For Ntacs systems, the choices are Ch LocSyntax and an example for Ntacs systems are as follows Ch Offset Chan Space User Defined This field sets the power control mode Selects Open Loop power control modeEventually dropped. See Drop Timer on Closed Loop Pwr Cntl Clr Scr CmaxThis field is used to clear the Ibasic controller screen Tests Ibasic Controller CCHannel command is used to control this field Current control channel settingCntl Chan Cnfg External Devices Test Save/Delete Procedure Cntry CodeCode Location Sets the base station’s country code to Confidence This field sets the confidence coefficient for FER testingSets a confidence coefficient of 95% Range of values floating point number 80 through Connect annunciator When a call is terminated, this annunciator will go out Connected annunciatorContinue Swered Cont/Single Controls Cdma Gated PowerControls Cdma Reverse Channel Spectrum Controls Cdma Swept Power Measurement Default selection is MainControls Open Loop Time Response Select among the following Controls Spectrum Analyzer Controls OscilloscopeCurrent Data Length Data ModeSets the User Data field data format to hexadecimal Data Rate Selects full-rate data transmission How to read the contents of the individual messages Data Spec Data Type Selects Prbs Date DC Current DC Level De-Emp Gain De-EmphasisDelete Ch Tests Channel Information Delet Ins Delet StpDescription Tests Order of Tests, External Devices Detector Detector Types Display DisarmStops a measurement in progress Setting the Display field to Data Call Control Screen Received Data Fields Information Strings Available From The Received Data Fields Information Strings Available When a Decoding Error Occurs Information Strings Available from Reverse Voice Channel Setting the Display Field to Meas Call Control Screen with Meas Selected Call Control Screen with NMeas Selected Enables displays of user messages Display Interim ResultsDisplay User Mssgs Displays interim FER results On how to read the contents of the individual messages Display Word Display Word Choices AuthWORD BSChalOrdMRI Ord Nrvc Ord RVCBSChal RVC OrdRVCOrdCon UniqChCon 235 Distn Enters 4 in the Drop Intcpt field Drop IntcptSee Also TDrop field description, on This field turns the call drop timer on or off Drop TimerTurns off the call drop timer Dsat DSAT/DST hex Sets the Dsat field to 0 2556CB Call Control when Namps is selected in the System Type field Dsat Meas Duplicate User Data Duplex OutEnters 2 times in the Duplicate Entered Data field Echo Delay Delays your voice 2 secondsEb/Nt Queries the Eb/Nt field Encoding Selects the Octet format Enter Ascii Data Enter Hex Data Errors Enter Procedure FilenameTests Save/Delete Procedure Errors Counted Queries the FER errors measurement result Enables escape mode Esc ModeESN dec ESN hex ESN Execute Handoff Executes the handoff Exec Execution Cond Execute Closed Loop Power Control ChangeExpected Expected PN Offset Queries the expected PN Offset value for Sector a Example Expected StrengthQueries the expected pilot strength value for Sector a Expected TAdd Queries the Expected TAdd value calculated by the Test Set Expected TDrop Queries the Expected TDrop value calculated by the Test Set External Disk Specification Ext Load R STD-008 Kor PCS Ext NghbField on FER Queries the currently displayed FER measurement result Clears the Errors Reported and Frames Reported fields FER Report ClearFER Spec FF at End FF at Start Filter Flow Cntl FirmwareFM Coupling FM Deviation FM Deviation Call Control Frame Clock Frames Counted FramesQueries the FER frames measurement result Freq Error Cdma Selects frequency error from the list of choicesQueries the Cdma frequency error measurement result Freq Channel Information Displays the Freq Error measurement field Freq Error AnalogCall Control when Meas is selected in the Display field Frequency Analog Gain Cntl Gate TimeSee Also Num of Bits field on Grid Gen-AnlTurns off the display grid Grid Cdma Swept Power Measurement HandoffSets the grid to on or off This field is used to initiate a handoff Hard Handoff annunciator Executes a Cdma to Analog handoff Ibasic Echo Gpib AdrsIbasic Ibasic Cntrl Ideal Mobile Power Queries the Ideal Mobile Power field Init Power If FilterIf Unit-Under-Test Fails Sets Initpwr to Input Att Ator hold mode Input AttenInformation Requires you to set the needed amount of input attenuation Input Gain Input Port Insert Ch Insrt Ins Inst Echo Insrt StpInst# Keep InternalThis field selects the trigger source Queries the length of the current SMS message length LengthProgramming Example for Keep Field Level div LibraryLines/Page Lower and Upper ACP RatioLevel Lower Limit Lvl Cdma Gated PowerQueries the level at the current marker position Lvl Open Loop Time Response Main Menu Marker Lvl Cdma Swept Power Measurement Marker FreqQueries the frequency at the marker’s present position Queries the amplitude at the marker’s present position Marker Lvl Marker Norm/Delta Marker TimeSelects Delta in this field Queries the difference in frequency between the two markers Marker Time Cdma Gated Power Marker Pos Cdma Reverse Channel SpectrumPositions the marker in the center of the display Positions the marker at 0 microseconds Marker Time Cdma Swept Power Measurement Marker Time Open Loop Time ResponsePositions the marker at 0 milliseconds Position is settable in units of milliseconds Marker To Mask Type Max FramesThis field sets the maximum frame count for each FER test Sets the maximum number of frames for FER measurements to Executes a Min/Max Power measurement Max PowerQueries the Max Power measurement value Max Req Seq, Max Rsp Seq Max Slot Cycle IndexSets both parameters to Sets the cycle to 2.56 seconds Message Data Mode Sets the measurement mode to singleCdma Gated Power unlabeled Meas Cntl Queries the Min Power measurement value Min PowerMic Pre-Emp Causes the Test Set to execute a Min/Max Power measurement Min/Max Pwr Identifies the mobile station parameter MUX1REV1 Mobile ParmSets the mobile station’s MUX1REV1 parameter value to Mobile Power Mode Mode Mobile PwrModel Mod In To MS Id Syntax for MS Id Field MS Ack Cause Code 304 Screens Where Annunciator is Present MS Ack Rcvd annunciator MS Database MS FER Protocol field on MS ID MS FER Report IntervalSets the mobile station’s FER report interval to 160 frames Enters the mobile station’s phone number Enters the mobile station’s MIN numberOperating Considerations for MS ID Field Netwrk Code Network IDSets the base station’s network code to Nghb Fq Ch Nom Power Nom Pwr ExtSets Nompwr to Sets Nompwrext to No Pk/Avg Normalize Notch Freq Notch Gain Notch Coupl Num of BitsBuffer has a maximum capacity See Also Gate Time field on Num Pages Num StepSets the Num Pages field to two Sets Numstep to Ocns Sector a Power Sets the Ocns Walsh code to Offset Freq Ocns Sector B PowerSets the Walsh code for the Ocns to Open Loop Time Response Execute Executes a time response to open loop power control testOptions Order Orig Addr Enters 1111111 in the Orig Addr field Tests Printer Setup, Execution Conditions Output Atten HoldOutput Heading Holds the output attenuators Tests Execution Conditions, Printer Setup Output PortOutput Results For This field selects the RF output port on the Test Set Output Results To Syntax Example Rate AnnunciatorSets the Page Rate field to full Send Specifies the messages to be sent Paging Sector a Power Sets Sector a pilot power to −16 dBSee Also Call/Page on Screens Where Field is Present Sent annunciator Pam Size ParameterParm Test Parameters Sets Pamsz to Parity Pass Word Phone Num PcmciaThis field provides re-formatting of Pcmcia cards Selects phase error from the list of choices Phs ErrorQueries the phase error measurement result Pilot Sector a Power Pilot Sector B PowerSets Sector a pilot power to −7 dB Sets Sector B pilot power to −7 dB Pilot Inc Sets the Pilot Inc field to Pilot Meas Clear Clears the contents of the Cdma Mobile Reporting tablePk Det To PN Offset Programming Example Status States Decimal Pilot Strength Level is above PN Offset Sector B Power PN Offset Sector a PowerSets the pilot PN offset index to Position Port/SweepThis control performs two functions Power Cntl Step Size Power Meas Refer to the Chan Power field description, onRefer to the Avg Power field description, on Gpib Example Operating Considerations, Power Zero Power Step This field allows entry of the power increment PwrstepPrint All Sets Pwrstep to Print Printer Setup Print Data DestinationPrinter Address Printer Port Priority Sets the Priority parameter to Urgent Procedure Library Proc Save/Delete ProcedurePrivacy Sets the Privacy parameter to Restricted Setting up a Call chapter in the E8285A Application Guide ProgramProtocol This field provides a choice of these protocol selections Enables or disables power down registration Pwr Dwn RegPwr Level Sets the Pwr Level Vmac field to Pwr Lvl Pwr Lvl field is divided into two fieldsLeft-Hand Field Right-Hand Field Pwr Up Reg Randa RandQueries the Rand field See Also SSD Update field on Screens Where Field is Present RandbRandssd Queries the Randssd field RANDSSD1 RANDSSD2 RANDSSD3 Randu Range Hold See Also Uniq Chall field on Screens Where Field is PresentQueries the Randu field Rcv Pace Receive pace field is used when receiving serial dataReceived Ref Level Cdma Swept Power Measurement Ref LevelSets the reference level to 0 dBm Sets the reference level high value Sets the timer-based registration period to Reg Period Register Cdma Register AnalogCauses the mobile to register MS ID field description, on Screens Where Field is Present Register annunciator Registering annunciator Queries the Cdma gated power release time Release Time Reset Res BW RF Anl Freq Cdma Swept Power Measurement Spectrum Analyzer When the Controls field is set to RF GenRF Channel analog Selects the RF analyzer frequency RF Channel Cdma Selects channel RF Chan Std Mobile Test Channel Range MHz Numbers E8285A Generate E8285A Receive RF Cnt Gate RF Display RF Gen Volts RF Gen FreqSets the RF generator to 815 MHz RF Level Offset RF Offset RF Out Queries the RF Power level RF PowerRgstr NID Rgstr SID Rssi Thresh RX/TX Cntl Run Run TestSAT Sets the SAT field to 6000 Hz SAT field is divided into two fields SAT Deviation TX Test Analog Sat Tol Save/Recall SCM Scope To Sc PrioritySets the search priority level in the custom neighbor list Sctr a Pwr Sets Sector A’s power to −100 dBmTurns on Sector a Select Procedure Filename Sctr B Pwr Tests Save/Delete Procedure Tests Main Menu Select Procedure LocationSend Msg Send Word Send Msg Cdma Swept Power MeasurementSTD-008 Kor PCS TSB-74 Serial Baud SensitivityThis area performs two functions Serial No Serial9This field displays the serial number of the Test Set Set Message Choices Set MessageBSChalCon FVCBSCon FVC O MesFVCUniqCh FVC V Mes MS InVCh MSMessOrd RandChalA RandChalB UniqChOrd Call Bit Set Message Field Descriptions 391 OHD This field displays the overhead message type 393 Settling Seqn Order of Tests SID MSB Sinad Slope Cdma Swept Power MeasurementSets the trigger slope SMS In Progress annunciator SMS Sent annunciatorSngl Step SNR SNR Operation This field controls softer handoffs Softer HandoffBegins a softer handoff Softer Handoff annunciator Soft SlopeQueries the Cdma condition register This field is used to enter the parameter Softslope Speaker ALC SpanSets the frequency span to 3 MHz Spec Pass/Fail Limits Speaker VolSpec# Squelch Srch Win a Sets search-window a to Srch Win N Sets search-window N to SSDA=0 annunciator Srch Win RSets search-window R to Ssda Ssdb Initiates the SSD Update procedure SSD UpdateAuthentication Tests, E8285A Application Guide SSD Update annunciator Status Mobile Reported Pilot Strength Programming example for Status Field Operating Considerations for Status Field Status Cdma Swept Power Measurement Zzzz new Status Cdma AuthenticationQueries for the arming status of the measurement Steps 251 Screens Where Field is PresentStep Size Step# Stop Length Strength Programming Example for Strength Field Swept Pwr Cdma Swept Power Measurement Sync Sector a PowerThis field allows for arming the swept power measurement Arms the measurement System ID System Type Call Control System Type CDMA-to-CDMA or CDMA-to-Analog Handoff All instances, the default is AmpsSelects the Amps system type for a Cdma to analog handoff TAdd TCompSets Tadd to Sets Tcomp to Operating Considerations This field allows entry of the pilot drop threshold Tdrop TDropSets Tdrop to Handoff Drop Timer Expiration Values TTDropTest Name Sets Ttdrop to Test Procedure Run Mode Test Status This field is duplicated on the Cdma Call Control screen This annunciator is lit when a FER test is in progressMeasured FER is displayed as 0.6% Measured FER is displayed as 1.4% Failed annunciatorExample Failed FER measurement Max Frames annunciator Time Configure TimeBase Time/div Time OffsetQueries the Cdma time offset measurement result Frequency Accuracy Definition IS-98 Timer Reg Time Offset Negative TM Test Mode Rho TM RhoSelects Traffic Rho as the current Rho measurement Queries the current Rho measurement result To Screen ConfigAnalog Trace Cdma Swept Power Measurement Total RAMThis field clears the measurement from the display Clears the screen Traffic Sector a Power Traffic Sector B PowerSets Sector B’s pilot power to −16 dB Sets the Walsh cover for Sector A’s traffic channel to Traffic Data Mode Selects service option Traffic Rho Transmitting annunciator Trig-Delay Tune Freq TX Power Transmitter Power measures RF power at the RF IN/OUT port 438 TX Pwr Meas TX Pwr Zero Type Initiates a Unique Challenge-Response procedureUniq Chall Uniq Chall annunciator Units Selects Ascii data entry mode for the User Data field Upper LimitUser Data Ascii or Hex Enters the Ascii string Call Home in the User Data field VC Order Vert/div Vert Offset Walsh Sector a Walsh Sector BSets Sector A’s traffic channel to Walsh code Sets Sector B’s traffic channel to Walsh code Transmit pace field is used when transmitting serial data Xmt Pace 448 Index Numerics 450 Index 451 452 Index 453 454 Index 455 456 Index 457 458 Index 459 460 Index 461 462 Index 463 464