RX/TX Cntl | Agilent Technologies E8285A specs

Chapter 4, Description of Fields

Fields

Screens Where Field is Present

CALL CONTROL

RX/TX Cntl

This function controls automatic screen changes between the RX TEST and TX

TEST screens during radio testing. It is divided into two fields:

The Auto/Manual field enables/disables automatic switching between the RX

TEST and TX TEST screens under certain testing conditions.

•Auto allows automatic screen changes between the RX TEST and TX TEST screens while testing radios.

•Manual requires you to select the RX TEST or TX TEST screen when performing ra- dio tests.

The Carrier/PTT field specifies the condition that will cause automatic screen changes.

•Carrier causes the instrument to automatically switch from the RX TEST screen to the TX TEST screen when an RF carrier is detected. The screen returns to RX TEST when the carrier is no longer detected.

•PTT (Push-To-Talk) causes the instrument to automatically switch from the TX TEST screen to the RX TEST screen when a microphone connected to the MIC/ACC connec- tor is keyed. The screen changes back to TX TEST when the microphone is no longer keyed.

Operating Considerations

CAUTION:The Test Set can be damaged by connecting a reverse-power signal to the DUPLEX OUT port of >200 mW.

If Auto and Carrier are used together, the screen may continuously change between RX TEST and TX TEST. This only occurs if the RF IN/OUT port is used with the RF Generator Amplitude set ≥ 35 dBm (a much higher level than is typically used for receiver tests). To prevent this problem, set the Amplitude ≤35 dBm or Off, or use the DUPLEX OUT port for the RF Generator’s output.

Screens Where Field is Present

CONFIGURE

373

Image 373

Agilent Technologies E8285A manual RX/TX Cntl

Contents

Reference Guide Copyright License under the clause at Dfars 52.227-7013 APR Herstellerbescheinigung Manufacturer’s Declaration General Safety Considerations for this Instrument Product Markings E8285A Cdma Mobile Station Test Set Duration of Warranty 1 year \agilent\e8285\REFGUIDE\MANUAL\frntmt.fb Declaration of Conformity Agilent Technologies E8285A Support Contacts Regional Sales and Service Offices Testing and for analog testing TestingThis Book Technologies E8285A Documentation Map Instrument Basic User’s Handbook E2083-90000 Specifications 5968-8839E Contents 101 100102 105 104106 108 148 144 Cmax Dsat ESN Contents MS FER Rand Randu SID MSB System ID 418 System Type Call Control Contents Keys are listed in alphabetical order Description of Keys Agilent Technologies E8285A Front Panel Address KeysAnswer This sets the Test Set’s Gpib address to Average AssignSee Also Programming Average Output 714MEASAFRDISTNAVERSTAT on Call/Page CancelEEX End/Release Ibasic resetEnter Hold This queries the increment value for the RF Gen Freq field Increment ÷10, Increment set, IncrementProgramming Increment set Output 714RFGFREQINCRMODE LOG Increment value from 10 MHz to 1 MHz FrequencyProgramming Increment÷10 Programming Increment ×10 K1 K5, & K1’- K3’Cannot be changed Local Puts the device at address 14 in local modeLow limit, High limit Programming Local Output 714MEASAFRDISTNHLIMSTAT? Used to display the high and low measurement limit values Analyzer FM deviation measurementDeviation measurement YES HLIMitEXCeeded? and LLIMitEXCeeded? commands to detect if aViation measurement have been exceeded To Detect If a Measurement Limit Has Been Exceeded. Use This resets all of the active measurements in the Test Set Meas resetProgramming Meas reset Programming Meter MeterTo Turn the Meter on and OFF To Set the Number of Intervals on the Meter To Query the State of the MeterTo Query the Number of Intervals on the Meter Meter for the TX power measurement Endpoint to 10 watts for the TX power measurementGraph meter high endpoint and low endpoint To Set the Meter High End and Low End Points To Set the Meter High End and Low End Point Display Units Graph meter for the TX power measurement to dBmTo Query the Meter High End and Low End Point Display Units Preset PowerNo Ratio W On/Off See Also Print Configure Screen on This recalls the instrument state saved in the file SETUP1Print Recall Programming Ref set Ref set Set a measurement reference point Commands to query a measurement reference point Measurement to dBm Register This saves the instrument state to a file named SETUP1Release Save Shift To 9, decimal point ., +/-, and a to F Yes On/Off Backspace Symbol KeysDown-Arrow, Up-Arrow E8285A User’s Guide Units-of-Measure Keys Front Panel Knobs Miscellaneous HardwareCursor Control Knob Key Name Screen Displayed Gpib Example Programmable Front-Panel Keys for Screens Non-Programmable Front-Panel Keys and Functions Data Functions Keys Guidelines for Using Measurement Data Functions Guidelines for Using Numeric Entry Field Data Functions User Keys Connectors are listed in alphabetical order Description of Connectors Agilent Technologies E8285A Rear Panel Description of Connectors Antenna ConnectorsOperating Considerations Audio in LOW, High Audio OUT Audio output is used to output signals from AF Generators 1AUD Monitor Output See Also Scope To field description, on Cell SITE/TRIGGERS Composite Video Cdma Clock MUX Output Even SEC Input Duplex OUTSee Also Cdma Clock MUX Output field description, on Gpib EXT REF InputSee Also Gpib Adrs field description, on Modulation Input Pin assignments for this connector are as followsPaging Channel Logging DCS2 Protocol Serial Parallel Port SA Trig Output RF IN/OUT Serial Port Serial Port 16X Chip Output Traffic Channel Logging DCS1See Also Cell SITE/TRIGGERS on See Also EXT REF Input on MHz Output These screens are listed in alphabetical order Description of Screens Adjacent Channel Power Screen Adjacent Channel Power Screen How the Test Set Measures Adjacent Channel Power ACP AF Analyzer Screen AF Analyzer Block Diagram onAF Analyzer Screen AF Analyzer Functional Block Diagram AF Analyzer Block Diagram Call Control Screen Call Control Screens Analog Meas Screen Call Control Screens Analog Meas How To Program The Analog Meas Screen Requirements for Using The Analog Meas Screen Authentication Screen Call Control Screens Authentication Call BIT Screen Call Control Screens Call BIT General Syntax Using the Call BIT Screen Example of Querying a Single Field Call BIT Screen Signaling Message NamesExample Printout General Syntax’ Printed Test Set Response MessageExample of Modifying Multiple Fields With One Output Call Configure Screen Call Control Screens Call Configure Call Data Screen Call Control Screens Call Data Messages which can be viewed are Aword Reading the Call Data Screen Message Fields Querying Multiple Fields With Single OUTPUT/ENTER Querying a Single Field Example of Querying a Single Field Cdma Authentication Screen Cdma Authentication Screen Cdma Call Control Screen Cdma Call Control Screen Cdma Cell Site Configuration Screen Cdma Cell Site Configuration Screen Cdma Cellular Mobile Receiver Test Screen Cdma Cellular Mobile Receiver Block Diagram onCdma Cellular Mobile Receiver Test Screen OUT Cdma Cellular Mobile Receiver Block Diagram Cdma Cellular Mobile Transmitter Test Screen Cdma Cellular Mobile Transmitter Test Screen Cdma Gated Power Screen Cdma Gated Power Screen Cdma Generator Control Screen Cdma Generator Control Block Diagram onCdma Generator Control Screen Lator Cdma Generator Control Block Diagram Cdma Mobile Reported FER Screen Cdma Mobile Reported FER Screen Cdma Mobile Reported Pilot Strength Screen Cdma Mobile Reported Pilot Strength Screen Cdma Open Loop Time Response Order Screen Cdma Open Loop Time Response Screen Cdma Reverse Channel Spectrum Screen Cdma Reverse Channel Spectrum Screen Cdma Short Message Service Screen Cdma Short Message Service Screen Cdma Swept Power Measurement Screen Cdma Swept Power Measurement Screen Cdma Transmitter Power Range Screen Cdma Transmitter Power Range Test Screen Configure Screen Configure Screen Duplex Test Screen Duplex Test Block Diagram onDuplex Test Screen Duplex Test Functional Block Diagram Duplex Test Block Diagram Help Screens I/O Configure Screen Message Screen Oscilloscope Screen and Menus Oscilloscope Screens Using the Scope To Field Oscilloscope Input IndicatorSelecting the Oscilloscope’s Input Printer Configurations Screen Print Configure Screen RF Analyzer Screen RF Analyzer Block Diagram onRF Analyzer Screen RF Analyzer Functional Block diagram RF Analyzer Block Diagram RF Generator Screen RF Generator Block Diagram onRF Generator Screen 2II RF Generator Functional Block Diagram RX Test Screen RX Test Block Diagram onRX Test Screen RX Test Fields and Their Functions RX Test Block Diagram Select Service from the To Screen menu Service Screen To access the functions without having to change menus Menus are accessed using the Controls fieldSpectrum Analyzer Screens Spectrum Analyzer Screen and Menus Setting Resolution Bandwidth and Sweep Rate Using the Spectrum AnalyzerAutomatic Calibration Description of the Tests Subsystem Tests ScreensTests Main Menu Screen Tests Main Menu Or SET UP Test SET lists This screen displays the channel frequencies to be tested Tests Channel InformationTests Channel Information Screen Tests Test Parameters Screen Tests Test Parameters Tests Order of Tests Screen Tests Order of Tests Tests Pass/Fail Limits Screen Tests Pass/Fail Limits Tests Save/Delete Procedure Screen Tests Save/Delete Procedure Tests Execution Conditions Screen Tests Executions Conditions Tests External Devices Screen Tests External Devices Tests Printer Setup screen determines how tests are run Tests Printer SetupTests Printer Setup Screen Tests Ibasic Controller Screen Tests Ibasic Controller TX Test Screen TX Test Block Diagram onTX Test Screen TX Test Functional Block Diagram TX Test Block Diagram 146 Field descriptions are listed in alphabetical order Description of Fields Screens Where Field is Present Access annunciatorFields Abort Print Selects the Access Probe Power measurement Avg PowerAcc Prb Pwr Acc Prb Pwr 150 AC Level Access Probe annunciator Active ACP Meas Active annunciatorTurned on Base station is not active Addr Add IntcptEnters 8 in the Add Intcpt field Tests External Devices AF Cnt Gate AF Anl AF Freq AFGen1 Lvl AFGen1 Freq AFGen2 Freq AFGen1 ToThis field has two fields AFGen2 To Entering an Akey Directly into the Test Set AKeyGenerating a New Akey Enters a 1 preceded by 19 0’s in the A-Key field Key Digits All Chans? AlertThis field sets the Alert parameter in SMS messages Sets the Alert parameter to On Selects All Bands in the Alt Pwr Ms Cal Bands field Alt Pwr Ms Cal Bands Queries the Cdma amplitude error measurement result Ampl ErrorAM Depth Amplitude See Also Atten Hold on Screens Where Field is Present Answer Mode Amplitude Cdma Swept Power MeasurementSelects manual mode Sets the trigger amplitude Antenna Sets the remote operation trigger mode to SingleArm Triggers all active measurements Disarm field description, on Screens Where Field is Present Queries the Cdma gated power attack timeAttack Time Atten Hold This field sets the Audio in LO connector’s stateAudio In Lo Authentication Tests, E8285A Application Guide Turns Authentication OnAudio Out Authen Clears the Authentication Data Table Authentication Data TableQueries the Cdma Authentication Data Table Authen Data Clear Data Position Numeric Value Reading the Authentication Data Table over Gpib 173 END Select Programming Example for Authentication Data Table 175 Auto/Norm AuthentThis field specifies how the trigger level is set Auto Zero Autostart Test Procedure on Power-UpTests Execution Conditions Operating Considerations for the Average Power Measurement Avg PowerAverages Queries the average power measurement Selects the average power measurementZeroes the average power measurement See Also Chan Power on Sets the Awgn generator’s level to −75 dBm Awgn Sets the Bandclass parameter to Band ClassIf Bandclass 1 or 4 is selected Base Freq User Defined Base Frequency is calculated using the following formula Beeper Base IDParameters Message from the Test Set BER Thresh Burst Time Queries the Cdma gated power burst time This field is coupled to the Span field’s setting By # errorsBW= Range of Values Called Number By # frames Calling Name This field is used for measuring access probe power levelsCall Limit Limits call progress to the paging channel Cdma Status Register Bit Definitions Call StatusRegistering annunciator on 360 Carrier Ref CarrierQueries the carrier feedthrough measurement result Center Freq Analog CC Order Center Freq Cdma Selects n up power control stepsChange Sets the center frequency to 850 MHz Chan is divided into two fields Chan Sets the Channel field to Channel Cdma to Analog or Interband Handoffs Channel BW Selects Channel Power measurements Chan PowerQueries the channel power measurement Operating Considerations for the Channel Power Measurement Chan Power Meas IntrvlSets the measurement interval to 1 ms Check Chan StdTests Pass/Fail Limits Check Digits Timer Reg field onMS Database field on Register Cdma field on For Ntacs systems, the choices are Ch LocSyntax and an example for Ntacs systems are as follows Chan Space User Defined Ch Offset Selects Open Loop power control mode This field sets the power control modeEventually dropped. See Drop Timer on Closed Loop Pwr Cntl Cmax Clr ScrThis field is used to clear the Ibasic controller screen Tests Ibasic Controller Current control channel setting CCHannel command is used to control this fieldCntl Chan Cnfg External Devices Cntry Code Test Save/Delete ProcedureCode Location Sets the base station’s country code to Confidence This field sets the confidence coefficient for FER testingSets a confidence coefficient of 95% Range of values floating point number 80 through Connect annunciator Connected annunciator When a call is terminated, this annunciator will go outContinue Swered Cont/Single Controls Cdma Gated PowerControls Cdma Reverse Channel Spectrum Default selection is Main Controls Cdma Swept Power MeasurementControls Open Loop Time Response Select among the following Controls Spectrum Analyzer Controls OscilloscopeCurrent Data Length Data ModeSets the User Data field data format to hexadecimal Selects full-rate data transmission Data Rate Data Spec How to read the contents of the individual messages Selects Prbs Data Type DC Current Date DC Level De-Emphasis De-Emp GainDelete Ch Tests Channel Information Delet Stp Delet InsDescription Tests Order of Tests, External Devices Detector Types Detector Display DisarmStops a measurement in progress Setting the Display field to Data Call Control Screen Received Data Fields Information Strings Available From The Received Data Fields Information Strings Available from Reverse Voice Channel Information Strings Available When a Decoding Error Occurs Setting the Display Field to Meas Call Control Screen with Meas Selected Call Control Screen with NMeas Selected Display Interim Results Enables displays of user messagesDisplay User Mssgs Displays interim FER results Display Word On how to read the contents of the individual messages BSChalOrd Display Word Choices AuthWORDMRI Ord Nrvc Ord RVC Ord RVCBSChalRVCOrdCon UniqChCon 235 Distn Enters 4 in the Drop Intcpt field Drop IntcptSee Also TDrop field description, on This field turns the call drop timer on or off Drop TimerTurns off the call drop timer Dsat Sets the Dsat field to 0 2556CB DSAT/DST hex Dsat Meas Call Control when Namps is selected in the System Type field Duplicate User Data Duplex OutEnters 2 times in the Duplicate Entered Data field Delays your voice 2 seconds Echo DelayEb/Nt Queries the Eb/Nt field Selects the Octet format Encoding Enter Hex Data Enter Ascii Data Errors Enter Procedure FilenameTests Save/Delete Procedure Queries the FER errors measurement result Errors Counted Enables escape mode Esc ModeESN dec ESN ESN hex Executes the handoff Execute Handoff Exec Execution Cond Execute Closed Loop Power Control ChangeExpected Queries the expected PN Offset value for Sector a Expected PN Offset Example Expected StrengthQueries the expected pilot strength value for Sector a Queries the Expected TAdd value calculated by the Test Set Expected TAdd Queries the Expected TDrop value calculated by the Test Set Expected TDrop Ext Load R External Disk Specification STD-008 Kor PCS Ext NghbField on Queries the currently displayed FER measurement result FER FER Report Clear Clears the Errors Reported and Frames Reported fieldsFER Spec FF at End Filter FF at Start Flow Cntl FirmwareFM Coupling FM Deviation Call Control FM Deviation Frame Clock Frames Counted FramesQueries the FER frames measurement result Selects frequency error from the list of choices Freq Error CdmaQueries the Cdma frequency error measurement result Freq Channel Information Displays the Freq Error measurement field Freq Error AnalogCall Control when Meas is selected in the Display field Frequency Analog Gain Cntl Gate TimeSee Also Num of Bits field on Grid Gen-AnlTurns off the display grid Handoff Grid Cdma Swept Power MeasurementSets the grid to on or off This field is used to initiate a handoff Executes a Cdma to Analog handoff Hard Handoff annunciator Ibasic Echo Gpib AdrsIbasic Ibasic Cntrl Queries the Ideal Mobile Power field Ideal Mobile Power If Filter Init PowerIf Unit-Under-Test Fails Sets Initpwr to Input Att Input Atten Ator hold modeInformation Requires you to set the needed amount of input attenuation Input Gain Input Port Insrt Ins Insert Ch Inst Echo Insrt StpInst# Keep InternalThis field selects the trigger source Queries the length of the current SMS message length LengthProgramming Example for Keep Field Library Level divLines/Page Lower and Upper ACP RatioLevel Lower Limit Lvl Cdma Gated PowerQueries the level at the current marker position Main Menu Lvl Open Loop Time Response Marker Freq Marker Lvl Cdma Swept Power MeasurementQueries the frequency at the marker’s present position Queries the amplitude at the marker’s present position Marker Lvl Marker Time Marker Norm/DeltaSelects Delta in this field Queries the difference in frequency between the two markers Marker Pos Cdma Reverse Channel Spectrum Marker Time Cdma Gated PowerPositions the marker in the center of the display Positions the marker at 0 microseconds Marker Time Open Loop Time Response Marker Time Cdma Swept Power MeasurementPositions the marker at 0 milliseconds Position is settable in units of milliseconds Marker To Max Frames Mask TypeThis field sets the maximum frame count for each FER test Sets the maximum number of frames for FER measurements to Executes a Min/Max Power measurement Max PowerQueries the Max Power measurement value Max Slot Cycle Index Max Req Seq, Max Rsp SeqSets both parameters to Sets the cycle to 2.56 seconds Sets the measurement mode to single Message Data ModeCdma Gated Power unlabeled Meas Cntl Queries the Min Power measurement value Min PowerMic Pre-Emp Min/Max Pwr Causes the Test Set to execute a Min/Max Power measurement Identifies the mobile station parameter MUX1REV1 Mobile ParmSets the mobile station’s MUX1REV1 parameter value to Mobile Power Mode Mode Mobile PwrModel Mod In To Syntax for MS Id Field MS Id MS Ack Cause Code 304 MS Ack Rcvd annunciator Screens Where Annunciator is Present MS Database Protocol field on MS FER MS ID MS FER Report IntervalSets the mobile station’s FER report interval to 160 frames Enters the mobile station’s phone number Enters the mobile station’s MIN numberOperating Considerations for MS ID Field Netwrk Code Network IDSets the base station’s network code to Nghb Fq Ch Nom Pwr Ext Nom PowerSets Nompwr to Sets Nompwrext to No Pk/Avg Normalize Notch Gain Notch Freq Num of Bits Notch CouplBuffer has a maximum capacity See Also Gate Time field on Num Step Num PagesSets the Num Pages field to two Sets Numstep to Sets the Ocns Walsh code to Ocns Sector a Power Offset Freq Ocns Sector B PowerSets the Walsh code for the Ocns to Open Loop Time Response Execute Executes a time response to open loop power control testOptions Order Enters 1111111 in the Orig Addr field Orig Addr Output Atten Hold Tests Printer Setup, Execution ConditionsOutput Heading Holds the output attenuators Output Port Tests Execution Conditions, Printer SetupOutput Results For This field selects the RF output port on the Test Set Syntax Example Output Results To Rate AnnunciatorSets the Page Rate field to full Specifies the messages to be sent Send Sets Sector a pilot power to −16 dB Paging Sector a PowerSee Also Call/Page on Screens Where Field is Present Sent annunciator Parameter Pam SizeParm Test Parameters Sets Pamsz to Pass Word Parity Phone Num PcmciaThis field provides re-formatting of Pcmcia cards Selects phase error from the list of choices Phs ErrorQueries the phase error measurement result Pilot Sector B Power Pilot Sector a PowerSets Sector a pilot power to −7 dB Sets Sector B pilot power to −7 dB Sets the Pilot Inc field to Pilot Inc Pilot Meas Clear Clears the contents of the Cdma Mobile Reporting tablePk Det To PN Offset Status States Decimal Pilot Strength Level is above Programming Example PN Offset Sector B Power PN Offset Sector a PowerSets the pilot PN offset index to Position Port/SweepThis control performs two functions Power Cntl Step Size Refer to the Chan Power field description, on Power MeasRefer to the Avg Power field description, on Gpib Example Operating Considerations, Power Zero This field allows entry of the power increment Pwrstep Power StepPrint All Sets Pwrstep to Print Data Destination Print Printer SetupPrinter Address Printer Port Sets the Priority parameter to Urgent Priority Proc Save/Delete Procedure Procedure LibraryPrivacy Sets the Privacy parameter to Restricted Program Setting up a Call chapter in the E8285A Application GuideProtocol This field provides a choice of these protocol selections Pwr Dwn Reg Enables or disables power down registrationPwr Level Sets the Pwr Level Vmac field to Pwr Lvl field is divided into two fields Pwr LvlLeft-Hand Field Right-Hand Field Pwr Up Reg Randa RandQueries the Rand field Randb See Also SSD Update field on Screens Where Field is PresentRandssd Queries the Randssd field RANDSSD2 RANDSSD1 Randu RANDSSD3 Range Hold See Also Uniq Chall field on Screens Where Field is PresentQueries the Randu field Rcv Pace Receive pace field is used when receiving serial dataReceived Ref Level Ref Level Cdma Swept Power MeasurementSets the reference level to 0 dBm Sets the reference level high value Reg Period Sets the timer-based registration period to Register Cdma Register AnalogCauses the mobile to register Register annunciator MS ID field description, on Screens Where Field is Present Registering annunciator Release Time Queries the Cdma gated power release time Res BW Reset Spectrum Analyzer When the Controls field is set to RF Gen RF Anl Freq Cdma Swept Power MeasurementRF Channel analog Selects the RF analyzer frequency Selects channel RF Channel Cdma RF Chan Std Range MHz Numbers E8285A Generate E8285A Receive Mobile Test Channel RF Display RF Cnt Gate RF Gen Volts RF Gen FreqSets the RF generator to 815 MHz RF Level Offset RF Out RF Offset Queries the RF Power level RF PowerRgstr NID Rssi Thresh Rgstr SID RX/TX Cntl Run Test RunSAT Sets the SAT field to 6000 Hz SAT field is divided into two fields TX Test Analog SAT Deviation Sat Tol SCM Save/Recall Scope To Sc PrioritySets the search priority level in the custom neighbor list Sctr a Pwr Sets Sector A’s power to −100 dBmTurns on Sector a Sctr B Pwr Select Procedure Filename Tests Save/Delete Procedure Tests Main Menu Select Procedure LocationSend Msg Send Word Send Msg Cdma Swept Power MeasurementSTD-008 Kor PCS TSB-74 Serial Baud SensitivityThis area performs two functions Serial No Serial9This field displays the serial number of the Test Set Set Message Choices Set MessageBSChalCon FVC O Mes FVCBSConFVCUniqCh FVC V Mes MSMessOrd MS InVCh RandChalB RandChalA Call Bit Set Message Field Descriptions UniqChOrd 391 OHD This field displays the overhead message type 393 Seqn Order of Tests Settling SID MSB Sinad Slope Cdma Swept Power MeasurementSets the trigger slope SMS In Progress annunciator SMS Sent annunciatorSngl Step SNR Operation SNR This field controls softer handoffs Softer HandoffBegins a softer handoff Soft Slope Softer Handoff annunciatorQueries the Cdma condition register This field is used to enter the parameter Softslope Speaker ALC SpanSets the frequency span to 3 MHz Spec Pass/Fail Limits Speaker VolSpec# Squelch Sets search-window a to Srch Win a Sets search-window N to Srch Win N SSDA=0 annunciator Srch Win RSets search-window R to Ssda Ssdb Initiates the SSD Update procedure SSD UpdateAuthentication Tests, E8285A Application Guide Status Mobile Reported Pilot Strength SSD Update annunciator Programming example for Status Field Operating Considerations for Status Field Status Cdma Swept Power Measurement Zzzz new Status Cdma AuthenticationQueries for the arming status of the measurement Steps 251 Screens Where Field is PresentStep Size Stop Length Step# Programming Example for Strength Field Strength Sync Sector a Power Swept Pwr Cdma Swept Power MeasurementThis field allows for arming the swept power measurement Arms the measurement System Type Call Control System ID System Type CDMA-to-CDMA or CDMA-to-Analog Handoff All instances, the default is AmpsSelects the Amps system type for a Cdma to analog handoff TComp TAddSets Tadd to Sets Tcomp to Operating Considerations This field allows entry of the pilot drop threshold Tdrop TDropSets Tdrop to TTDrop Handoff Drop Timer Expiration ValuesTest Name Sets Ttdrop to Test Status Test Procedure Run Mode This field is duplicated on the Cdma Call Control screen This annunciator is lit when a FER test is in progressMeasured FER is displayed as 0.6% Failed annunciator Measured FER is displayed as 1.4%Example Failed FER measurement Max Frames annunciator TimeBase Time Configure Time Offset Time/divQueries the Cdma time offset measurement result Frequency Accuracy Definition IS-98 Time Offset Negative Timer Reg TM Rho TM Test Mode RhoSelects Traffic Rho as the current Rho measurement Queries the current Rho measurement result To Screen ConfigAnalog Total RAM Trace Cdma Swept Power MeasurementThis field clears the measurement from the display Clears the screen Traffic Sector B Power Traffic Sector a PowerSets Sector B’s pilot power to −16 dB Sets the Walsh cover for Sector A’s traffic channel to Selects service option Traffic Data Mode Transmitting annunciator Traffic Rho Trig-Delay Tune Freq Transmitter Power measures RF power at the RF IN/OUT port TX Power 438 TX Pwr Meas TX Pwr Zero Type Initiates a Unique Challenge-Response procedureUniq Chall Units Uniq Chall annunciator Upper Limit Selects Ascii data entry mode for the User Data fieldUser Data Ascii or Hex Enters the Ascii string Call Home in the User Data field VC Order Vert Offset Vert/div Walsh Sector B Walsh Sector aSets Sector A’s traffic channel to Walsh code Sets Sector B’s traffic channel to Walsh code Xmt Pace Transmit pace field is used when transmitting serial data 448 Numerics Index 450 Index 451 452 Index 453 454 Index 455 456 Index 457 458 Index 459 460 Index 461 462 Index 463 464