Cisco Systems NPE-175, NPE-225 - page 76

6-14

Network Processing Engine and Network Services Engine Installation and Configuration

OL-4448-12

Chapter 6 NPE-G2 Overview

NPE-G2 Memory Information and Specifications

Note With reference to the RJ-45 pinout in Table 6-7, proper common-mode line terminations should be used

for the unused Category 5 UTP cable pairs 4/5 and 7/8. Common-mode termination reduces

electromagnetic interference (EMI).

Depending on your RJ-45 interface cabling requirements, use the pinouts shown in Figure 6-6 and

Figure 6-7 for Gigabit Ethernet straight-through and crossover twisted-pair cable connections. Use

Figure 6-8 for Ethernet/Fast Ethernet straight-through and crossover twisted-pair cable connections.

Figure 6-6 Four Twisted-Pair Straight-Through Cable Schematics for 10/100/1000 and

1000BASET SFP Module Ports

Tab l e 6-7 RJ-45 Port Pinouts

Pin 10/100 Signal Gigabit Ethernet Signal

1Tx Data+1

1. Tx Data = Transmit Data

Tx A+

2Tx Data– Tx A–

3Rx Data+2

2. Rx Data = Receive Data

Rx B+

4N/C Tx C+

5N/C Tx C–

6Rx Data– Rx B–

7N/C Rx D+

8NC Rx D–

1Router 2Hub

1 2

1 TPO+

2 TPO-

3 TP1+

6 TP1-

1 TP1+

2 TP1-

3 TPO+

6 TPO-

4 TP2+

5 TP2-

7 TP3+

8 TP3-

4 TP3+

5 TP3-

7 TP2+

8 TP2-

129086

Contents

Main Page CONTENTS Page Page Page Page Page Page Page Preface Document Revision History Objectives Organization Related Documentation Obtaining Documentation and Submitting a Service Request NPE-100, NPE-150, and NPE-200 Overview Software Requirements NPE-100, NPE-150, and NPE-200 Description and Overview Page Page Page Page NPE-100, NPE-150, and NPE-200 Memory Information NPE-100 Memory Information NPE-150 Memory Information NPE-200 Memory Information NPE-175 and NPE-225 Overview Software Requirements NPE-175 and NPE-225 Description and Overview Page Page Page NPE-175 and NPE-225 Memory Information Page NPE-300 and NPE-400 Overview NPE-300 and NPE-400 Description and Overview Page Page NPE-300 and NPE-400 Memory Information Page Page Page NSE-1 Overview Software Requirements NSE-1 Description and Overview Page Page NSE-1 Memory Information Page Page NPE-G1 Overview NPE-G1 Description and Overview Bandwidth Page Interfaces and LEDs 2 4 5 7 9 10 1 3 68 CompactFlash Disk 1 32 Summary of Important NPE-G1 Information Page NPE-G1 Memory Information Connection Equipment and Specifications Ethernet and Fast Ethernet RJ-45 Connection Equipment Page 5-12 1Router 2Hub Gigabit Ethernet GBIC Connection Equipment 1 2 3 34 5 Page Page Mode-Conditioning Patch Cord Description Console and Auxiliary Port Connection Equipment / / / / 87 6 34 5 / / Page RJ-45 Console Port Signals and Pinouts RJ-45 Auxiliary Port Signals and Pinouts NPE-G2 Overview Software Requirements NPE-G2 Description and Overview Bandwidth Requirements Interfaces LEDs 2 4 6 8 31 5 7 10 11 13 9 12 CompactFlash Disk 1 32 USB Ports Summary of Important NPE-G2 Information Page 6-11 primary cache with separate instruction and data cache memory, but unified secondary cache. USBuniversal serial bus. NPE-G2 Memory Information and Specifications Page Connection Equipment and Specifications Ethernet and Fast Ethernet RJ-45 Connection Equipment Page 1 2 3 34 5 Gigabit Ethernet SFP Connection Equipment Page Page Mode-Conditioning Patch Cord Description Console and Auxiliary Port Connection Equipment / / / / 65 4 3 7 / / 1 7 Page RJ-45 Console Port Signals and Pinouts RJ-45 Auxiliary Port Signals and Pinouts Page NPE-G1 and NPE-G2 Installation and Configuration Information Preparing for an Upgrade Page Copying the Configuration File Copying the Configuration File to a Flash Disk or PC Card Copying the Configuration File to a TFTP Server Page Copying the Configuration File Using a PC Removing the Network Processing Engine Ensuring Easy Access to the Router Powering Down the Router and Disconnecting Input Power Powering Down the Router Disconnecting AC-Input Power from a Cisco 7200 VXR Router Disconnecting AC-Input Power from a Cisco uBR7246VXR Router Disconnecting AC-Input Power from a Cisco uBR7225VXR Router Disconnecting DC-Input Power from a Cisco 7200 VXR Router 3 4 Disconnecting DC-Input Power from a Cisco uBR7246VXR Router Page Page Removing the NPE or NSE-1 1 2 3 4 Installing the NPE-G1 or NPE-G2 Basic Guidelines Installing a CompactFlash Disk Installing a USB Flash Memory Module or eTokenNPE-G2 1 3 Installing an SFP ModuleNPE-G2 1 2 3 Page Installing a GBICNPE-G1 Replacing the DIMM on the NPE-G2 Page Upgrading the SDRAM SODIMMs on the NPE-G1 (Optional) Removing a SODIMM Installing a SDRAM SODIMM Inserting the NPE-G1 or NPE-G2 into the Router Attaching the Rear Cable-Management Brackets and Cables (Optional) Installing the NPE-G1 or NPE-G2 Cable-Management Brackets 7-30 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 NETWORK PROCESSING ENGINE - G1 CONSOLE AUX NETWORK PROCESSING ENGINE-300 Installing the Rear Cable-Management Brackets on a Front-Mounted Router (Optional) Installing the Rear Cable-Management Brackets on a Rear-Mounted Router (Optional) 7-33 Network Processing Engine and Network Services Engine Installation and Configuration OL-4448-12 CONSOLE AUX NETWORK PROCESSING ENGINE - G1 CONSOLEAUX Installing the Default Cable-Management Bracket on a Cisco uBR7246VXR Router (Optional) Reconnecting Input Power and Powering Up the Router Reconnecting AC-Input Power to the Cisco 7200 VXR Router Page Reconnecting AC-Input Power to the Cisco uBR7246VXR Router Reconnecting AC-Input Power to the Cisco uBR7225VXR Router Reconnecting DC-Input Power to the Cisco 7200 VXR Router Page Page Reconnecting DC-Input Power to a Cisco uBR7246VXR Router Page Page Page Powering Up the Router Enabling the Second Processor on the NPE-G1 Error Messages Using show Commands Associated with the mpf Command 7-48 Using the show interface stats Command Use the show interface stats command for information about the interface. Using the show ip interface Command Use the show ip interface command to get information about the specific interface port. 7-49 Using the show mpf cpu Command Using the show mpf cpu history Command 7-50 Using the show mpf interface Command Using the show mpf interface GigabitEthernet 0/1 Command Using the show mpf interface GigabitEthernet 0/1 100 Command Using the show mpf ip exact-route Command Using the show mpf punt Command Using the show version Command Copying the Saved Configuration to NVRAM Copying the Saved Configuration File from a Flash Disk or PC Card Copying the Saved Configuration File from the CompactFlash Disk Downloading the Saved Configuration from the TFTP Server Page Auxiliary and Console Port Information Configuring an Auxiliary Port to Receive Console Port Messages Configuring the Native Gigabit Ethernet Interfaces Changing the Media Type of the Native Gigabit Ethernet GBIC, SFP, or RJ-45 Ports Configuring the Interface Transmission and Speed Modes Sample Configuration for the Gigabit Ethernet Interfaces Debugging Resetting the Interface Clearing Counters Using show Commands to Check the Installation Page 7-61 Use the show interface or show interface slot/port command to display status information: Upgrading the Cisco IOS Image and the Boot Helper (Boot Loader) Image Upgrading ROMmon on the NPE-G1 or NPE-G2 7-64 Using the show rom-monitor Command and ROMmon CLI showmon Commands If you are in Cisco IOS, use the show rom-monitor command: If you are in ROMmon, use the ROMmon CLI showmon command: Using the upgrade rom-monitor file Command Changing Preferences to Choose the Other ROMmon Image Troubleshooting the Upgrade 7-66 ROMmon Upgrade Error Messages One if these error message appears when the upgrade has failed or if the upgrade image is corrupted: ROMmon image is not compatible with the ReadOnly image: ROMmon upgrade image is too big: Hardware does not support ROMmon upgrade: Upgrading FPGA on the NPE-G2 Troubleshooting the NPE-G1 or NPE-G2 Page Preparation for Installation Required Tools and Equipment Software and Hardware Requirements NPE or NSE Requirements 4 5 763 Page Port Adapter Jacket Card Support Software Requirements Page Page Page Safety Guidelines 8-9 Safety Warnings 8-10 8-11 8-12 Page Electrical Equipment Guidelines Telephone Wiring Guidelines Electrostatic Discharge Prevention Page Removing and Installing the NPE or NSE Ensuring Easy Access to the Router Removing and Replacing the NPE or NSE Powering Down the Router and Disconnecting Input Power Powering Down the Router Disconnecting AC-Input Power from a Cisco 7200 Series Router or Cisco 7200 VXR Router Disconnecting AC-Input Power from a Cisco uBR7200 Series Router Disconnecting DC-Input Power from a Cisco 7200 Series Router or Cisco 7200 VXR Router Page Disconnecting DC-Input Power from a Cisco uBR7246 Router Page Removing the NPE or NSE 1 2 3 4 Removing and Installing Memory Removing DRAM SIMMs Page Installing DRAM SIMMs 3 2 Removing SDRAM DIMMs Page Installing SDRAM DIMMs Page Removing a SDRAM SODIMM Installing a SDRAM SODIMM Checking a SDRAM Upgrade or Replacement Installing the NPE or NSE Page Reconnecting Input Power and Powering Up the Router Page Reconnecting AC-Input Power to the Cisco 7200 Series Router or Cisco 7200 VXR Router Reconnecting AC-Input Power to the Cisco uBR7200 Series Router Reconnecting DC-Input Power to a Cisco 7200 Series Router or Cisco 7200 VXR Router Page Reconnecting DC-Input Power to a Cisco uBR7246VXR Router Page Page Page Powering Up the Router Page Configuration Tasks and Troubleshooting Information NPE Configuration Tasks NSE Configuration Tasks Boot Changes in Cisco IOS Release 12.2 Troubleshooting the NPE-G1 or NPE-G2 Page .Troubleshooting the NPE-100 Through NPE-400 NPE or NSE show Commands Using the show version Command 10-5 Using the show c7200 Command Use the show c7200 command to obtain information about the router. Using the show environment Command with the NPE-G2NPE-G2 -Specific Output NSE-1 show Commands Using the show pxf accounting ? Command and Subcommands 10-7 The following is an example of the show pxf accounting interface command with sample output: Using the show pxf crash Command The following is an example of the show pxf crash command with sample output: 10-8 Using the show pxf info Command The following is an example of the show pxf info command with sample output: 10-9 Using the show pxf interface Command Using the show pxf feature ? Command and Subcommands The following is an example of the feature-specific show pxf feature ? command with sample output: show pxf feature cef ? NSE-1 Error Messages Using Debugging Commands and PXF PXF Troubleshooting Information 10-12 High Route Processor CPU Usage Page Removing and Replacing an AC-Input or DC-Input Power Supply Removing a Power Supply from a Cisco 7200 Series Router Replacing a Power Supply in a Cisco 7200 Series Router Page Page Page INDEX B C D I L M N P R S T U