Table 5-5

Error Messages

154

Table 5-6

Procedure for Starting Up the Controller

155

Table 5-7

Operating Mode Definitions

156

Table 5-8

Changing Operating Modes

157

Table 5-9

Procedure for Selecting Automatic or Manual Mode

158

Table 5-10

Procedure for Selecting the Local Setpoint Source

160

Table 5-11

Procedure for Changing the Local Setpoints

161

Table 5-12

Procedure for Enabling (or Disabling) the Remote Setpoint

162

Table 5-13

Setpoint Selection Indication

162

Table 5-14

Procedure for Configuring a Setpoint Ramp

164

Table 5-15

Procedure for Running a Setpoint Ramp

166

Table 5-16

Procedure for Selecting Two Sets of Tuning Constants

168

Table 5-17

Procedure for Setting Switchover Values

169

Table 5-18

Procedure for Setting Tuning Constant Values

169

Table 5-19

Procedure for Switching PID SETS from the Keyboard

170

Table 5-20

Procedure for Displaying or Changing the Alarm Setpoints

171

Table 5-21

Control Loop Selections

172

Table 5-22

Two-loop Functionality and Restrictions (Model DC330E-EE-2XX or

 

 

Model DC330E-EE-5XX)

175

Table 5-23

Two-loop Functionality and Restrictions (Model DC330E-KE-2XX or

 

 

Model DC330E-KE-5XX)

176

Table 5-24

Procedure for Selecting 2-loop Algorithm

177

Table 5-25

Procedure for Selecting Output Algorithm

177

Table 5-26

Procedure for Selecting Control Parameters

178

Table 5-27

Procedure for Selecting Tuning Parameters

179

Table 5-28

Digital Display Indication— Two Loops

180

Table 5-29

Procedure for Displaying the 3PSTEP Motor Position

182

Table 5-30

Digital Input Option Action on Contact Closure

186

Table 5-31

Digital Input Combinations “DIG IN1” or “DIG IN2”

188

Table 5-32

Digital Inputs 1 and 2 Combination

189

Table 5-33

Auto/Manual Station Mode Configuration Procedure

191

Table 5-34

Accutune Rules and Regulations

195

Table 5-35

Procedure for Starting TUNE (Demand) Tuning

196

Table 5-36

Procedure for Using TUNE at Start-up for Duplex

197

Table 5-37

Procedure for Using SP Tuning at Start-up

198

Table 5-38

Procedure for Using SP Tuning at Start-up for Duplex

199

Table 5-39

Accutune* Error Prompt Definitions

201

Table 6-1

Setpoint Program Data Entry Procedure

211

Table 6-2

Prompt Hierarchy and Available Selections

212

Table 6-3

Run/Monitor Functions

214

Table 6-4

Procedures for Changing a Running Setpoint Program

217

Table 7-1

Voltage and Resistance Equivalents for 0% and 100% Range Values

220

Table 7-2

Equipment Needed

222

Table 7-3

Set Up Wiring Procedure for Thermocouple Inputs Using an Ice Bath

223

Table 7-4

Set Up Wiring Procedure for Thermocouple Inputs Using a Precision Resistor

224

Table 7-5

Input #1, #2, or #3 Calibration Procedure

229

Table 7-6

Restoring Factory Calibration

231

Table 8-1

Set Up Wiring Procedure Current Proportional Output

234

Table 8-2

Current Proportional Output Calibration Procedure

235

Table 8-3

Position Proportional and 3 Position Step Output Calibration Procedure

237

Table 8-4

Set Up Wiring Procedure for Auxiliary Output

240

Table 8-5

Auxiliary Output Calibration Procedure

241

Table 9-1

Error Message Prompts

245

x

UDC 3300 Controller Product Manual

4/00

Page 10
Image 10
Honeywell UDC 3300 manual 154