Intel mcs-48 manual PIN Description, Gnd

8243

PIN DESCRIPTION

Symbol	Pin No.	Function
PROG	7	Clock Input. A high to low
		transistion on PROG signi.fies
		that address and control are
		available on P20-P23, and a low
		to high transition signifies that
		data is available on P20-23.
	6	Chip Select Input. A high on CS
		inhil;lits any change of output or
		internal status.
P20-P23	11-8	Four (4) bit bi-directional port
		contains the address and con-
		trol bits on a high to'low
		transition of PROG. During a
		low to high transition contains
		the data for a selected output
		port if a write operation, or the
		data from a selected port before
		the low to high transition if a
		read operation.
GND	12	ovolt supply.
P40-P43	2-5	Four (4) bit bi-directional 110
P50-P53	1,23-21	ports. May be programmed
P60-P63	20-17	to be input (during read),
P70-P73	13-16	low impedance latched output
		(after write) or a tri-state (after
		read). Data on pins P20-23 may
		be directly written, ANDed or
		ORed with previous data.
Vee	24	+5 volt supply.

FUNCTIONAL DESCRIPTION

General Operation

The 8243 contains four 4-bit 1/0 ports which serve as an extension of the on-chip 1/0 and are addressed as ports 4-

7.The following operations may be performed on these ports:

•Transfer Accumulator to Port.

•Transfer Port to Accumulator.

•AND Accumulator to Port,

•OR Accumulator to Port.

All communication between the 8048 and the 8243 occurs over Port 2 (P20-P23) with timing provided by an output pulse on the PROG pi'nof the processor. Each transfer consists of two 4-bit nibbles:

The first containing the "op code" and port address and the second containing the actual 4-bits of data.

A high to low transition of the PROG line indicates that address is present while a low to high transition indicates the presence of data. Additional 8243'smay be added to the 4-bit bus and chip selected using additional output lines from the 8048/8748/8035.

Power On Initialization

Initial application of power to the device forces input/output ports 4, 5, 6, and 7 to the tri-state and port 2 to the input mode. The PROG pin may be either:high or low when power is applied. The first high to low transition of PROG causes device to exit power on mode. The power on sequence is initiated if Vee drops below 1V.

P21 P20 Address Code P23 P22 Instruction Code

0	0	Port 4	0	0	Read
0	1	Port 5	0		Write
1	0	Port 6	1	0	ORlD
1		Port 7			ANlD

Write Modes

The device has three write modes. MOVD Pi, A directly writes new data into the selected port and old data is lost. ORlD Pi,A takes new data, OR'sit with the old data and then writes it to the port. ANlD Pi,A takes new data AND's it with the old data and then writes it to the port. Operation code and port address are latched from the input port 2 on the high to low transition of the PROG pin. On the low to high transition of PROG data on port 2 is transferred to the logic block of the specified output port.

After the logic manipulation is performed, the data is latched and outputed. The old data remains latched until new valid outputs are entered.

Read Mode

The device has one read mode. The operation code and port address are latched from the input port 2 on the high to low transition of the PROG pin. As soon as the read operation and port address are decoded, the appropriate outputs are tri-stated, and the input buffers switched on. The read operation is terminated by a low to high transition of the PROG pin. The port (4, 5, 6 or 7) that was selected Is switched to the tri-stated mode while port 2 is returned to the input mode.

Normally, a port will be in an'output(write mode) orinput (read mode). If modes are changed during operation, the first read following a write should be ignored; all follow- ing reads are valid. This is to allow the external driver on the port to settle after the first read instruction removes the low impedance drive from the 8243 output. A read of any port will leave that port in a high impedance state.

&-58 AFN-00214A-Q2