Manuals / Brands / Communications / Telephone / Toshiba / Communications / Telephone

Toshiba DK 16, DK8 7-10, FIGURE 7-8 DK16 DOOR LOCK CONTROL OPTION (PIOU/PIOUS)

1 321

Download 321 pages, 2.3 Mb

INSTALLATION-PERIPHERALS

SECTION 100-816-207

MARCH 1993

7-10FIGURE 7-8DK16 DOOR LOCK CONTROL OPTION (PIOU/PIOUS)

programmed to activate continuously when the

Night Transfer 1 button (only) is set to NIGHT

mode (for indirect answering machine control); or

to pulsate at 1-second ON/3-seconds OFF (for a

night bell) when incoming CO lines night ring over

external page (Program 78-13) (NT1 = tenant 1

CO lines; NT2 = tenant 2 CO lines) per Program

15.

3.33 When configured for the Music-on-Hold func-

tion with Program 77-1, the relay activates any

time a CO line is on hold. In this configuration, the

relay is normally used to control the Music-on-Hold

source.

3.34 DK16 Night Transfer Relay Control. Con-

figure the PIOU or PIOUS for the Night Transfer

Relay function in accordance with the following

steps (refer to Figures 7-6 and 7-7):

1) Access Program 77-1. Set LED 05 to OFF to

configure the Night/Hold Relay for the Night

Relay function.

2) Access Program 77-1. Set LED 06 to provide

continuous or pulsating relay activation as

follows:

OFF—Programs the relay for continuous

activation when NT1 button (only) is set.

ON—Programs the relay for pulsating

activation when the NT1 or NT2 button

is set to NIGHT mode and a tenant 1 or

tenant 2 CO line rings.

NOTE:

CO lines must be enabled in Program 78-13

for the NT pulsating relay function.

3) Access Programs 87, 88, and 89 to set the

CO lines that will activate the relay (when the

system is in the NIGHT mode).

4) Access Program 39 to program a Night

Transfer button (NT1 or NT2) on all tele-

phones that are to transfer the system into the

NIGHT mode.

P10

B

M

PIN 34, R-BR

PIN 9, BR-R

17

18

MDF

PIOU

W1

K1

MAKE

DET

DER

MDF

PIOUS

TO DOOR LOCK

SEE

FOR WIRING

TO DOOR LOCK

BREAK

DE

TERMINAL ON FRONT EDGE OF PCB

NOTE:

Unlock Door 0

assigned to digital and electronic

telephones in Program 39 with

Code 71.

K1/P10 (24VDC, 1.0 AMP MAX.)

25-PAIR

AMPHENOL

DET

DER

FIGURE 8-23

SEE ,

LED 07, 20

FOR RELAY OPTIONS

PROGRAM 77-1

DOOR LOCK 0 BUTTON

Contents

Main Digital Key Telephone Systems DK8 & DK16 INSTALLATION AND MAINTENANCE MANUAL Telecommunication Systems Division Page INSTALLATION Page Page Page 1-1 1 PURPOSE 2 ORGANIZATION 3 REFERENCE DOCUMENTATION 4 SYSTEM MNEMONICS/TERMS 1-2 1-3 1-4 The system cannot support the PIOU and PIOUS simultaneously. Only one or the other can be installed. 1-5 Page Page Page 2-1 2 INPUT POWER REQUIREMENTS not dedicated 3 SITE CONSIDERATIONS 2-2 4 GROUNDING REQUIREMENTS FIGURE 2-3 DK16 COMBINED BASE AND EXPANSION KEY SERVICE UNIT INSTALLATION-SITE REQUIREMENTS SECTION 100-816-202 2-3 TABLE 2-A SUMMARY OF ELECTRICAL/ENVIRONMENTAL CHARACTERISTICS FIGURE 2-4 KSU GROUNDING DIAGRAM 2-4 If the reading is more than one ohm, then the outlet is not adequately grounded. Page Page 3-i TABLE TITLE PAGE WORKSHEETS NUMBER TITLE PAGE Page 3-1 1 INTRODUCTION 2 SYSTEM CAPACITY 3-2 TABLE 3-A DK8 CO LINE/STATION CONFIGURATION GUIDE TABLE 3-B DK16 CO LINE/STATION CONFIGURATION GUIDE (BASE AND EXPANSION UNIT) 3-3 TABLE 3-C DK8 KEY SERVICE UNIT COMPONENTS * Page 3-5 TABLE 3-E DK16 EXPANSION KEY SERVICE UNIT PCBs 3 STATION CONSIDERATIONS 3-6 TABLE 3-F PIOU/PIOUS INTERFACE OPTION (DK16 ONLY) Expansion Unit Interface Options PIOU PIOUS TABLE 3-G STRATA DK8 STATION APPARATUS OVERVIEW * * 3-8 3-9 4 TELEPHONE UPGRADES 5 CONFIGURATION EXAMPLES 3-10 6 CONFIGURATION WORKSHEETS 3-11 DK8 WORKSHEET 1, STATION AND CO LINE TOTALS Maximum of 2 items total, including Standard Telephones: 3-12 DK8 WORKSHEET 2, KEY SERVICE UNIT AND PCBs 3-13 DK8 WORKSHEET 3, PERIPHERALS AND UPGRADES 3-14 DK8 WORKSHEET 3, PERIPHERALS AND UPGRADES (continued) 3-15 DK16 WORKSHEET 1, STATION AND CO LINE TOTALS Maximum of 12 items total, including Standard Telephones: 3-16 DK16 WORKSHEET 2, KEY SERVICE UNIT AND PCBs 3-17 DK16 WORKSHEET 3, PERIPHERALS AND UPGRADES 3-18 DK16 WORKSHEET 3, PERIPHERALS AND UPGRADES (continued) 3-19 DK16 WORKSHEET 4, SYSTEM POWER CHECK Total Power Used: * All series. Page Page Page 4-i 4-ii TABLE OF CONTENTS (CONTINUED) 4-1 secure the hard board to the wall, making certain that screws are aligned with studs. Install screws first to the hard board, and then FIGURE 4-1 DK8 KEY SERVICE UNIT WALL MOUNT METHOD PART I. KSU INSTALLATION 4-2 FIGURE 4-2 DK8 DIMENSIONS AND SCREW LOCATIONS 4-3 FIGURE 4-3 DK8 SIDE VIEW DIMENSION AND PLUG/JACK LOCATIONS LEFT SIDE VIEW RIGHT SIDE VIEW 4-4 4-5 3 POWER SUPPLY REMOVAL AND 4 DK8 POWER FAILURE EMERGENCY TRANSFER OPTION 4-6 FIGURE 4-4 DK8 CABLING DIAGRAM LEFT SIDE VIEW RIGHT SIDE VIEW TO HPFB FG SCREW 4-7 FIGURE 4-5 DK8 BASE UNIT JACKS AND CONNECTORS 4-8 FIGURE 4-6 DK8 KEY SERVICE UNIT POWER FAILURE TRANSFER (PFT) CIRCUIT DIAGRAM 4-9 PART II. PRINTED CIRCUIT BOARD 5 GENERAL 6 PCB INSTALLATION CONSIDERATIONS call and three parties on the second simulta- neous conference. 4-10 FIGURE 4-7 DK8 PRINTED CIRCUIT BOARD INSTALLATION J16 CDU J1 4-11 FIGURE 4-8 QCDU CONTROLS AND INTERFACE CONNECTORS 4-12 FIGURE 4-9 MODULAR JACK COVER REMOVAL AND STORAGE 4-13 8 STANDARD TELEPHONE INTERFACE UNIT (QSTU) standard telephones (or any other device con- nected to a QSTU port), a QRCU must be installed. QSTU Ports are fixed. They are assigned even if a QSTU is not installed. 9 DTMF RECEIVER/ABR TONE DETECTOR UNIT (QRCU) 4-14 FIGURE 4-10 QSTU CONTROLS AND INTERFACE CONNECTORS 4-15 DK8RCU1A V.1 FIGURE 4-11 QRCU INTERFACE CONNECTORS 4-17 12 BUILT-IN CO LINE, DIGITAL TELE- PHONE, AND OTHER CIRCUITS Page Page Page 5-i TABLE OF CONTENTS (continued) Page Page 5-1 PART I. KSU INSTALLATION 1 GENERAL 2 KEY SERVICE UNIT MOUNTING 5-2 FIGURE 5-1 DK16 BASE KEY SERVICE UNIT EXTERIOR FIGURE 5-2 DK16 BASE KEY SERVICE UNIT WALL MOUNTING METHODS 5-3 FIGURE 5-3 DK16 BASE KEY SERVICE UNIT INTERIOR SW 400 NOR PAD 5-4 5-5 FIGURE 5-4 DK16 BASE KEY SERVICE UNIT WIRING CONNECTIONS NOTES 1. 2. SUPPLIED IN PLASTIC BAG WITH BASE UNIT. DO NOT ROUTE POWER CORD WITH OTHER CORDS. 5-6 FIGURE 5-5 CONNECTING THE DK16 EXPANSION UNIT TO THE DK16 BASE UNIT 5-7 FIGURE 5-6 MOUNTING THE DK16 EXPANSION UNIT Page 5-9 FIGURE 5-8 DK16 EXPANSION UNIT WIRING CONNECTIONS 5-10 5-11 FIGURE 5-9 RESERVE POWER/BATTERY WIRING 3 POWER SUPPLY REMOVAL AND 5-12 FIGURE 5-10 POWER SUPPLY (KPSU16) 5-13 PART II. DK16 PRINTED CIRCUIT BOARD 4 GENERAL 5 DK16 PCB INSTALLATION CONSIDERATIONS 5-14 6 BASE UNIT STANDARD TELEPHONE INTERFACE UNIT (KSTU) FIGURE 5-11 KSTU OPTIONS AND CONNECTORS 5-15 KSTU Ports (08~11) are fixed. They are as- signed even if a KSTU is not installed. 7 DIGITAL TELEPHONE INTERFACE UNIT (PDKU) TABLE 5-A KSTU CONTROLS AND INTERFACE CONNECTORS 5-16 FIGURE 5-12 PDKU INTERFACE CONNECTION 5-17 8 ELECTRONIC TELEPHONE INTERFACE UNIT (PEKU) Ensure the PDKU's component side is facing right when installing it in the KSU. 5-18 FIGURE 5-13 PEKU CONTROLS AND INTERFACE CONNECTORS 5-19 TABLE 5-B PEKU CONTROLS AND INTERFACE CONNECTORS 5-20 9 STANDARD TELEPHONE INTERFACE UNIT (PSTU) FIGURE 5-14 OFF-HOOK CALL ANNOUNCE UNIT (EOCU) INTERFACE CONNECTORS 5-21 FIGURE 5-15 PSTU AND SUBUNIT (SSTU) TABLE 5-C PSTU CONTROLS AND INTERFACE CONNECTORS PSTU1 (V.4) became available in November 1989. PSTU1(V.3) was discontinued. 5-22 10 STANDARD/ELECTRONIC TELE- PHONE INTERFACE UNIT (PESU) 5-23 INSTALLATION-DK 16 KSU & PCB MARCH 1993 FIGURE 5-16 PESU PCB OPTION LOCATION AND IDENTIFICATION NOTE: Connect two ringers maximum per port (H or L). 5-24 TABLE 5-D PESU CONTROLS AND INTERFACE CONNECTORS 5-25 A special code is not required to connect BGM to a PESU. 11 CO LINE UNIT (PCOU) 5-26 FIGURE 5-17 PCOU CONTROLS, INDICATORS, AND INTERFACE CONNECTORS 5-27 TABLE 5-E PCOU CONTROLS, INDICATORS, AND INTERFACE CONNECTORS 5-28 12 OPTION INTERFACE UNIT (PIOU AND PIOUS) FIGURE 5-18 PIOU CONTROLS, INDICATORS, AND INTERFACE CONNECTORS 5-29 TABLE 5-F PIOU CONTROLS AND INTERFACE CONNECTORS 5-30 FIGURE 5-19 PIOUS PCB SWITCH/JUMPER, OPTION LOCATION Refer to Remote Maintenance Procedures, Section 100-816-600, for information regard- ing the IMDU. 5-31 TABLE 5-G PIOUS CONTROLS AND INTERFACE CONNECTORS 13 CO LINE/DIGITAL TELEPHONE INTERFACE UNIT (KCDU) 5-32 FIGURE 5-20 REMOTE MAINTENANCE MODEM UNIT (IMDU) IINTERFACE CONNECTORS FIGURE 5-21 KCDU INDICATORS, OPTIONS, AND CONNECTORS 5-33 TABLE 5-H KCDU CONTROLS, INDICATORS, AND CONNECTORS 14 DTMF RECEIVER/ABR TONE DETECTOR UNIT (K4RCU) 5-34 15 BUILT-IN CO LINE AND DIGITAL TELEPHONE CIRCUITS FIGURE 5-22 K4RCU PCB 5-35 16 KCOU REMOVAL AND FIGURE 5-23 KCOU PCB 5-36 FIGURE 5-24 DK16 BASE UNIT POWER FAILURE TRANSFER (PFT) CIRCUIT DIAGRAM 17 DK16 POWER FAILURE EMERGENCY TRANSFER OPTION Page Page 6-i 6-ii 6-1 1 OVERVIEW 2 TELEPHONE INSTALLATION 6-2 Page 6-4 3 DIGITAL TELEPHONE UPGRADES 6-5 DIGITAL TELEPHONE TOP ASSEMBLY PDIU-DI2 2000 DIGITAL TELEPHONE BASE TO P1 OF BOTTOM PCB RS-232 (FEMALE) DB-25 CONNECTOR FIGURE 6-4 PDIU-DI2 INSTALLATION INTO 2000-SERIES DIGITAL TELEPHONE 6-6 FIGURE 6-6 DVSU INSTALLATION FOR DIGITAL 6-7 FIGURE 6-8 DKT2010-SD, DKT2020-S, AND DKT2020-SD STRAP AND CONNECTOR LOCATIONS FIGURE 6-7 DKT2010-H STRAP AND CONNECTOR LOCATIONS FIGURE 6-9 1000-SERIES DIGITAL TELEPHONE STRAP AND CONNECTION LOCATIONS 6-8 Do not cut the OCA strap if connecting an HESB to the HHEU for the Loud Ringing FIGURE 6-10 HHEU INSTALLATION FOR DIGITAL TELEPHONE FIGURE 6-11 HESC-65A CABLING 6-9 Belleven if a headset is also installed on the HHEU. It is not necessary to cut these straps if the headset is connected to the HHEU. 6-10 6-11 4 ELECTRONIC TELEPHONE UPGRADE OPTIONS (DK16 Only) FIGURE 6-12 HVSU2 INSTALLATION FOR ELECTRONIC 6-12 FIGURE 6-13 ELECTRONIC TELEPHONE PCB CONNECTIONS FIGURE 6-14 HVSI/HVSU INSTALLATION FOR ELECTRONIC 6-13 FIGURE 6-15 HHEU INSTALLATION FOR ELECTRONIC 6-14 5 DIRECT STATION SELECTION CONSOLE/SYSTEM CONNECTION (DK16 Only) 6-15 6 DOOR PHONE/LOCK CONTROL UNIT AND DOOR PHONE INSTALLATION 6-16 DK8 and DK16 do not support the HDCB. DDCBs cannot connect to the QSTU, KSTU, PSTU, PESU or PEKU. FIGURE 6-16 DOOR PHONE (DDCB) INSTALLATION 6-17 FIGURE 6-17 DOOR PHONE (MDFB) INSTALLATION 7 ADD-ON MODULE INSTALLATION 6-18 FIGURE 6-20 DK8 ADD-ON MODULE DSS BUTTON ASSIGNMENTS FIGURE 6-18 ADD-ON MODULE INSTALLATION FIGURE 6-19 DK16 ADD-ON MODULE DSS BUTTON ASSIGNMENTS Page Page 7-i 7-ii 7-1 1 GENERAL 2 MUSIC-ON-HOLD/BACKGROUND MUSIC OPTIONS 7-2 * * 7-3 7-4 FIGURE 7-2 DK16 BGM SOURCE/STANDARD TELEPHONE CIRCUIT PRECAUTION DIAGRAM 3 RELAY CONTROL OPTIONS * * 7-5 FIGURE 7-3 DK8 AND DK16 MUSIC SOURCE CONFIGURATION A FIGURE 7-4 DK8 AND DK16 MUSIC SOURCE CONFIGURATION B 7-6 FIGURE 7-5 DK16 MUSIC SOURCE CONFIGURATION C 7-7 The above relay options are available in con- junction with the Base Unit relay option. Do not connect relays directly to 120VAC power source. 7-8 FIGURE 7-6 DK16 PIOU RELAY CONTROL FUNCTIONAL WIRING DIAGRAM 7-9 FIGURE 7-7 DK16 PIOUS RELAY CONTROL FUNCTIONAL WIRING DIAGRAM 3.25 Door Lock Assignments Guide 7-10 FIGURE 7-8 DK16 DOOR LOCK CONTROL OPTION (PIOU/PIOUS) CO lines must be enabled in Program 78-13 for the NT pulsating relay function. 7-11 FIGURE 7-9 DK8 AND DK16 DOOR LOCK CONTROL OPTION (DDCB) 7-12 4 EXTERNAL SPEAKER UNIT (HESB) OPTIONS 7-13 7-14 FIGURE 7-10 DK8 AND DK16 HESB/DIGITAL TELEPHONE WITH LOUD RINGING BELL WIRING 7-15 FIGURE 7-11 DK16 HESB/ELECTRONIC TELEPHONE WITH LOUD RINGING BELL WIRING NOTE: See Section 100-816-206 for instructions on how to cut the HHEU strap inside the telephone. 7-16 7-17 FIGURE 7-12 DK8 AND DK16 HESB/AMPLIFIED SPEAKER WIRING 7-18 FIGURE 7-13 DK8 AND DK16 HESB/TALKBACK AMPLIFIED SPEAKER WIRING 7-19 FIGURE 7-14 HESB WALL MOUNTING 5 EXTERNAL PAGE OPTIONS Multi-zone page output rating is 30W/maxi- mum at 300 ohms. 7-20 FIGURE 7-15 DK8 AND DK16 PAGE AND SEPARATE BGM USING SAME AMPLIFIER 7-21 FIGURE 7-16 DK16 PIOU ZONE, PAGE/BGM/NIGHT RING (SEPARATE AMPLIFIERS) Program 77-1 Button/LED Zone/ Assignment LED OFF Relay LED ON 7-22 FIGURE 7-17 DK16 PAGING WITH MULTIPLE AMPLIFIERS 7-23 IMPORTANT NOTE: To night ring over selected PAGE zone, see Paragraph 9 of this section. or 6 DK8 AND DK16 STATION MESSAGE DETAIL RECORDING (SMDR) PRINTER/ CALL ACCOUNTING DEVICE OPTIONS 7-24 INPUT FIGURE 7-18 DK16 NIGHT RINGING OVER ALL EXTERNAL PAGE ZONES NOTES: 1. Page signal path . 2. Night ring signal path . OUTPUT 7-25 7-26 FIGURE 7-19 DK8 AND DK16 SMDR PRINTOUT EXAMPLES NOTES: 1. 2. 3. 4. 5. 6. * * 7-27 97 7-28 FIGURE 7-20 DK8 AND DK16 PIOU/PIOUS SMDR CABLE CONNECTIONS * 7 VOICE MAIL OPTIONS 7-29 FIGURE 7-21 PIOU/PIOUS SMDR PORT (PROGRAM 97) DATA DUMP EXAMPLE 7-30 FIGURE 7-22 DK8 AND DK16 VOICE MAIL/AUTO ATTENDANT BLOCK DIAGRAM same 7-31 The DK8 QRCU or DK16 K4RCU must be installed to allow End-to-End Signaling. Installation and Maintenance Manual A, D, and B tones should be enabled only for VM/AA devices that respond to these tones. 7-32 8 DK16 ALARM SENSOR INSTALLATION 7-33 9 DK16 NIGHT RINGING OVER EXTERNAL ZONE PAGE FIGURE 7-23 DK16 ALARM SENSOR BLOCK DIAGRAM (PIOU/PIOUS) 7-34 10 DATA INTERFACE UNIT 7-35 Data Interface User Guide Installation & Maintenance Manual Operating Procedures. 7-36 7-37 7-38 7-39 7-40 Do not cut PDIU-DS PERCEPTION jumper wire for STRATA DK8 or DK16 installations. 7-41 FIGURE 7-24 DK8 OR DK16 DATA INSTALLATION EXAMPLE BLOCK DIAGRAM 7-42 FIGURE 7-25 DK8 AND DK16 PDIU-DI TO IBM AT-TYPE COMPUTER, RS-232 CONNECTOR/CABLE CONNECTIONS TOSHIBA LAPTOP OR IBM AT-TYPE PERSONAL COMPUTER (DTE) PDIU-DI (FUNCTIONS LIKE A DCE) 7-43 FIGURE 7-26 DK8 AND DK16 PDIU-DI TO IBM XT-TYPE COMPUTER, RS-232 CONNECTOR/CABLE CONNECTIONS IBM XT PERSONAL COMPUTER OR ASCII TERMINAL (FUNCTIONS LIKE A DTE) PDIU-DI (FUNCTIONS LIKE A DCE) 7-44 FIGURE 7-27 DK8 AND DK16 PDIU-DS TO TOSHIBA PRINTER, RS-232 CONNECTOR/CABLE CONNECTIONS TOSHIBA PS321SL PRINTER (FUNCTIONS LIKE A DTE) PDIU-DS (CONFIGURED IN THE "CONNECT TO DTE" MODE: P1 ~ P9 = A-B SO PDIU FUNCTIONS LIKE A DCE) 7-45 FIGURE 7-28 DK8 AND DK16 PDIU-DS TO HAYES-TYPE SMART MODEM, RS-232 CONNECTOR/CABLE CONNECTIONS HAYES-TYPE SMART MODEM (FUNCTIONS LIKE A DCE) PDIU-DS (CONFIGURED IN THE "CONNECT TO MODEM" MODE, P1 ~ P9 = B-C, SO IT FUNCTIONS LIKE A DTE) 7-46 FIGURE 7-29 DK8 AND DK16 PDIU-DI/PDIU-DS MODULAR CABLE/RJ-45 ADAPTER CONNECTIONS CONNECTION EXAMPLE 1 IMPORTANT! Will not function with applications that require the RI signal to PC. CONNECTION EXAMPLE 2 7-47 FIGURE 7-30 DK8 AND DK16 PDIU-DI/PDIU-DS MODULAR CORDS AND RJ-45/RS-232 ADAPTER PIN CONNECTIONS TYPE 1 RJ45 TO DB9 (FEMALE) ADAPTER Modular Cords (50 ft max, 24AWG; customer-supplied) 8 7-48 FIGURE 7-31 DK8 AND DK16 PDIU-DS JUMPER PLUG OPTIONS/RS-232 CONNECTOR INFORMATION MODULAR JACK FOR CONNECTING 1- OR 2-PAIR TO DIGITAL CIRCUIT PERCEPTION A-B DTE 7-49 PDIU-DI AND -DS SW1 DIP SWITCH (1 ~ 4) FUNCTIONS FIGURE 7-32 DK8 AND DK16 PDIU-DI/PDIU-DS SW1 DIP SWITCH INFORMATION PDIU-DI (BOTTOM VIEW) PDIU-DS (REAR VIEW) 7-50 FIGURE 7-33 DK8 AND DK16 PDIU-DS DISASSEMBLY/ASSEMBLY DIAGRAM 7-51 FIGURE 7-34 DK8 AND DK16 PC TO PC TEST CALL USING AT COMMANDS 7-52 Para- graph 10.63) FIGURE 7-35 DK8 AND DK16 PC TO PRINTER TEST CALL USING MANUAL DIALING 7-53 FIGURE 7-36 DK8 AND DK16 INTERNAL PC TO EXTERNAL PC TEST CALL USING AT COMMANDS 7-54 FIGURE 7-37 DK8 AND DK16 EXTERNAL PC TO INTERNAL PC TEST CALL USING AT COMMANDS 7-55 7-56 11 DK16 TWO-CO LINE EXTERNAL AMPLIFIED CONFERENCE FIGURE 7-38 DK8 AND DK16 PC AUTO DIAL VOICE CALL TEST 7-57 NOTES (Amplifier): 1. 2. 3. 4. NOTES (PROGRAMMING): Program 10-3, circuit assignments FIGURE 7-39 DK16 AMPLIFIED TWO-CO LINE CONFERENCE AND/OR AMPLIFIED DISA FUNCTIONAL WIRING DIAGRAM 7-58 Page Page 8-i Page 8-1 2 WIRING DIAGRAMS TABLE 8-A FCC REGISTRATION NUMBERS STRATA DK8 AND DK16 8-2 TABLE 8-B STATION LOOP REQUIREMENTS or 8-3 TABLE 8-C NETWORK REQUIREMENTS * Circuits 1 and 2 8-4 TABLE 8-D DIGITAL TELEPHONE/DIU/DDSS CONSOLE/ADM/LOOP LIMITS 8-5 MARCH 1993 FIGURE 8-1 SECONDARY PROTECTOR DIAGRAM 8-6 8-7 FIGURE 8-2 DK8 MDF WIRING TO KSU AMPHENOL STATION AND RELAY CONNECTIONS NOTES: 1. 8-8 FIGURE 8-3 DK8 MDF WIRING TO CO LINES (KSU AND QCDU) BRIDGING CLIPS CO1 CO2 8-9 See Note 3 & 4 FIGURE 8-4 DK8/DK16 MDF WIRING DDCB AND DOOR LOCK CONTROL 8-10 FIGURE 8-5 DK8 QSTU/DK16 KSTU STATION/MDF CROSS CONNECT RECORD FIGURE 8-6 DK8 AND DK16 CO LINE RECORD 8-11 FIGURE 8-7 DK8 QSMU TTY/SMDR WIRING NOTE 1: NOTE 2: Wire colors may vary with other types of modular adaptors. 8-12 25-PAIR CABLE W/MALE AMP CONNECTOR NOTES: Voltage levels: T, PT = R, PR = (Reference to FG ground) 1. 2. 3. FIGURE 8-8 DK16 MDF WIRING/BASE UNIT P5 AMPHENOL STATION AND RELAY CONNECTIONS 8-13 FIGURE 8-9 DK16 MDF WIRING/CO LINES TO BASE UNIT 8-14 SECTION 100-816-208 NOTES: Voltage levels: T, PT = R, PR = (Reference to FG ground) g station runs per Table 8-D. PT/PR ma 8-15 NOTES: 1. 2. 3 4. 5. DIU 8-16 8-17 FIGURE 8-13 DK16 MDF WIRING/ELECTRONIC TELEPHONE TO PEKU BRIDGING CLIPS DR NOTES: 8-18 NOTE: Place PEKU SW1 to DSS. NOTE: See Program 28 for electronic telephone to DSS assignments. NOTE: All cable 24 AWG max loop resistance: 20 ohms from PEKU to DSS (500 ft). NOTE: See Program 29 to assign DSS buttons. 8-19 FIGURE 8-15 DK16 PEKU BACKGROUND MUSIC CONNECTION BRIDGING CLIPS NOT USED NOTES: 8-20 not shown, see MDF-to-electronic telephone wirin FIGURE 8-16 DK16 PEKU STATION/MDF CROSS CONNECT RECORD 8-21 FIGURE 8-17 DK16 MDF WIRING/STANDARD TELEPHONE, VOICE MAIL TO PSTU 25-PAIR CABLE W/MALE AMP CONNECTOR 8-22 NOTES: 1. Indicate if standard telephone, voice mail port, etc. 2. Circuit 3 or 8 can support a Back round Music ( BGM 8-23 BRIDGING CLIPS Program 31 RING 2 RING 8-24 FIGURE 8-20 DK16 PESU STATION/MDF CROSS CONNECT RECORD 8-25 FIGURE 8-21 DK16 MDF WIRING/CO LINES TO PCOU 8-26 CO LINE CABLING FIGURE 8-22 DK16 MDF WIRING/CO LINES AND DIGITAL TELEPHONES TO KCDU NOTES: Voltage levels: T, PT = R, PR = (Reference to SG ground) 1. 2. 3. 8-27 SELECT RELAY FUNCTION WITH PROGRAM 77-1 DOOR LOCK OR AMP. CONTROL SELECT RELAY FUNCTION WITH PROGRAM 77-1: NIGHT RELAY OR MOH CONTROL MUTE CONTROL ALSO PROVIDED BY BASE UNIT PAGE RELAY (PIN 42 AND 17 OF P5 AMPHENOL) NOTE: This figure shows PIOU relay callouts. See Chapter 5 for PIOUS relay callouts. 8-28 NOTE 2: Wire colors may vary with other types of modular adaptors. Sets the IMDU and TTY jack for bell or CCITT specification. "W4 not installed". W4 BELL - 8-29 PIOUS FIGURE 8-25 DK16 PIOUS PAGE/RELAY/ALARM CONNECTIONS 8-30 FIGURE 8-26 DK16 PIOU SMDR/TTY OPTIONS AND WIRING NOTE 1: P13 8-31 BRIDGING CLIPS CIRCUIT 4 TO EKT CIRCUIT 5 TO EKT CIRCUIT 8 TO EKT 8-32 AC/DC EXTERNAL POWER SOURCE SPECIFICATIONS: FIGURE 8-28 DK16 EXTERNAL POWER FOR DIGITAL TELEPHONE CONNECTION Page Page -i- Page -1- as described in All fault clearing must begin with the Fault Classifica- tion Flowchart 2 FAULT CLASSIFICATION TABLE A FLOWCHARTS -2- 4 DEFECTIVE APPARATUS RETURNS 5 FAULT IDENTIFICATION AND ELIMINATION PROCEDURES 6 DK8 HARDWARE FAULT ISOLATION -3- FIGURE 3 KPSU16 DC VOLTAGE TEST FIGURE 2 QPSU8 DC VOLTAGE TEST -4- Important Note: Do not attempt to replace Fuse F201 7 DK16 HARDWARE FAULT ISOLATION 8 STATION CABLE CONTINUITY CHECK Perform the following at the locations indi- cated: -5- 9 FAULT ISOLATION FLOW CHARTS -6- TABLE C (ELECTRONIC TELEPHONE CABLES) CHECK USING OHMMETER TABLE E (DIGITAL TELEPHONE CABLES) CHECK USING OHMMETER -7- CHART NO. 1 FAULT CLASSIFICATION -8- CHART NO. 2 CATASTROPHIC FAULTS NOTE: Program 03 is not used for DK8. -9- CHART NO. 3 STATION DIAL TONE FAULTS -10- CHART NO. 4 CO LINE DIAL TONE FAULTS NOTE: Program 03 is not used on DK8. -11- CHART NO.5 DSS CONSOLE FAULTS (DK16 ONLY) -12- CHART NO.6 VOICE MAIL/(EXTERNAL) AUTO ATTENDANT (VM/AA) FAULTS -13- CHART NO.7 STATION MESSAGE DETAIL RECORDING (SMDR) FAULTS -14- CHART NO.8 REMOTE MAINTENANCE FAULTS Page Page -i- -ii- TABLE LIST (Continued) -iii- Page -1- 1 USING REMOTE ADMINISTRATION AND MAINTENANCE 1.01 Figure 1 is provided as a quick reference aid in using this section. FIGURE 1 SECTION FLOWCHART 3 HARDWARE REQUIREMENTS 2 GENERAL DESCRIPTION -3- DK8 OR DK16 DK8 OR DK16 FIGURE 2 REMOTE MAINTENANCE EXTERNAL MODEM CONNECTION FOR DK8 & DK16 METHOD ONE FIGURE 3 REMOTE MAINTENANCE EXTERNAL MODEM CONNECTION FOR DK8 & DK16 METHOD TWO -4- TABLE RM-A PPTC MODIFIED WIRING FOR EXTERNAL MODEM TO TTY CONNECTION * FIGURE 4 REMOTE MAINTENANCE USING IMDU MODEM (DK16 ONLY) DK16 PPCT (Modular to DB25) ADAPTOR, MODIFIED WIRING FOR CONNECTING TTY JACK TO AN EXTERNAL MODEM: IMPORTANT: FIGURE 5 LOCAL MAINTENANCE USING ASCII TERMINAL OR PERSONAL COMPUTER TABLE RM-B PPTC WIRING FOR LOCAL TERMINAL OR PERSONAL COMPUTER TO TTY CONNECTION 4 TERMINAL/MODEM INSTALLATION Page Page 5 LOCAL TERMINAL OPERATION 6 REMOTE TERMINAL OPERATION If a personal computer is being used, connect the cable to the serial COM port. 7 MODE SELECTION 8 PROGRAM MODE TABLE RM-CPROGRAMMING PROMPTS 9 DATA DUMP MODE 10 TEST MODE FIGURE 7 SAMPLE PRINTOUT OF SYSTEM MESSAGES FIGURE 6 DATA DUMP PRINTOUT EXAMPLE FIGURE 8 TEST MODE FUNCTION DIAGRAM 11 LCD MESSAGE MODE 12 SPEED DIAL MODE 13 MODE EXIT To exit the Message Mode, the terminal key- board must be in lower case. 14 DISCONTINUE OPERATION 15 EQUIPMENT COMPATIBILITY -15- TABLE RM-D NOTE: If program data is not entered correctly, then Program 77-1 , LED 14. If using the IMDU for remote programming, go into -16- TABLE RM-E at the same time NOTE: If program data is not entered correctly, PROGRAM 92 STATION SPEED DIAL, SPEED DIAL MEMO, VM ID CODES INITIALIZATION -17- TABLE RM-F at the same time NOTE: If program data is not entered correctly, PROGRAM 92 (continued) SYSTEM SPEED DIAL, SPEED DIAL MEMO INITIALIZATION TABLE RM-G -18- PROGRAM 92 (continued) LCD CHARACTER MESSAGE MEMORY INITIALIZATION at the same time NOTE: If program data is not entered correctly, -19- TABLE RM-H at the same time NOTE: If program data is not entered correctly, PROGRAM 92 (continued) TIMED REMINDERS INITIALIZATION -20- TABLE RM-I at the same time NOTE: If program data is not entered correctly, PROGRAM 92 (continued) DIGITAL TELEPHONE VOLUME LEVEL INITIALIZATION TABLE RM-J -21- PROGRAM 92 (continued) CALL FORWARD BACKUP RAM INITIALIZATION at the same time NOTE: If program data is not entered correctly, TABLE RM-K -22- PROGRAM 03 SLOT ASSIGNMENTS TABLE RM-L -23- PROGRAM 00 SOFTWARE CHECK/REMOTE MAINTENANCESECURITY CODE TABLE RM-M -24- PROGRAM 01 LOGICAL PORT DISPLAY TABLE RM-N PROGRAM 02 PHYSICAL PORT DISPLAY -25- A blank is displayed by "N". TABLE RM-P TABLE RM-O Programs 10-1, 10-2, and 10-3 use Type 1 procedure. -26- TABLE RM-Q NOTE: This step is optional and not required to save data. TYPE 1 PROGRAM PROCEDURE EXAMPLE NOTE: Most programs do not require a second digit. -27- TABLE RM-R TYPE 2 PROGRAM PROCEDURE EXAMPLE Y = button/LED "ON", N = button/LED TABLE RM-S -28- PROGRAM 12 SYSTEM ASSIGNMENTS BASIC TIMING TABLE RM-T 1. A blank is displayed by "N". 2. Programs 15 and 16 use Type 1 procedure. TABLE RM-U -29- PROGRAM 19 BACKGROUND MUSIC SLOT IDENTIFICATION TABLE RM-V PROGRAM 21 MODEM POOLING TABLE RM-W -30- PROGRAM 22 DATA STATION HUNTING (DATA CALL ONLY) ital and electronic telephones. TABLE RM-X -31- TABLE RM-Y pe 1 procedure. PROGRAM 29 DSS CONSOLE BUTTON ASSIGNMENTS Pro TABLE RM-Z TABLE RM-AA -32- PROGRAM 32 AUTOMATIC PREFERENCE PROGRAM 33 STATION HUNTING TABLE RM-AB -33- PROGRAM 34 HOLD RECALL TIMING TABLE RM-AC NOTE: , use T TABLE RM-AD -34- PROGRAM 37 RING TRANSFER (CAMP-ON) RECALL TIME TABLE RM-AE -35- PROGRAM 38 DIGITAL AND ELECTRONIC TELEPHONE BUTTONSTRIP TYPE -36- TABLE RM-AF pe 1 procedure.2. PROGRAM 39 FLEXIBLE BUTTON ASSIGNMENT 1. Program 40, 41: use Type 2 procedure. Pro -37- TABLE RM-AG PROGRAM 42-1 ~ 8 PBX ACCESS CODE -38- TABLE RM-AH PROGRAM 60 SMDR OUTPUT/ACCOUNT CODE DIGIT LENGTH -39- TABLE RM-AI PROGRAM 69 VERIFIABLE ACCOUNT CODE ENTRY Note: The number of digits will be as defined in TABLE RM-AJ -40- PROGRAM 70 VERIFY ACCOUNT CODE/TOLL RESTRICTION ASSIGNMENT pe 1 procedure. Pro -41- TABLE RM-AK pe 2 procedure. PROGRAM 78 CO LINE SPECIAL RINGING ASSIGNMENTS-DISA/IMDU/ NIGHT RINGING OVER EXTERNAL PAGE Pro TABLE RM-AL -42- PROGRAM 80 DIGITAL AND ELECTRONIC TELEPHONE RINGING TONES pe 2 procedure. NOTE: Pro -43- TABLE RM-AM PROGRAM 93 CO LINE IDENTIFICATION to clear characters. NOTE: Use -44- TABLE RM-AN TABLE RM-AO PROGRAM 44 (A OR B) TOLL RESTRICTION TRAVELING CLASS OVERRIDE CODE ENTRY PROGRAM 45-1 TOLL RESTRICTION DIAL PLAN -45- TABLE RM-AP PROGRAM 45-2 TOLL RESTRICTION DISABLE TABLE RM-AQ PROGRAM 45-3 ~ 6 EQUAL ACCESS, SPECIAL COMMON CARRIER NUMBERS, and AUTHORIZATION CODE DIGIT LENGTH * PROGRAM 45-8 ~ 9 TOLL RESTRICTION OVERRIDE CODE TABLE RM-AS PROGRAM 462 ~ 4 TOLL RESTRICTION ALLOWED/DENIED AREA CODES ASSIGNED BY CLASS -47- * -48- TABLE RM-AU PROGRAM 46-10 ~ 40 TOLL RESTRICTION CLASS PARAMETERS TABLE RM-AV -49- PROGRAM 47 TOLL RESTRICTION EXCEPTION OFFICE CODES ASSIGNED BY AREA CODE -50- TABLE RM-AW TABLE RM-AX PROGRAM 48 STATION TOLL RESTRICTION CLASSIFICATION PROGRAM 50-1 LCR PARAMETERS -51- TABLE RM-AY PROGRAM 50-2 LCR HOME AREA CODE TABLE RM-AZ PROGRAM 50-31 ~ 35 LCR SPECIAL CODES -52- TABLE RM-BA PROGRAM 50-4 LCR LDI PLAN NUMBER TABLE RM-BB PROGRAM 50-5 LCR LOCAL CALL PLAN NUMBER * PROGRAM 50-6 LCR DIAL ZERO TIMEOUT TABLE RM-BD PROGRAM 51 LCR AREA CODES -54- * PROGRAM 52 LCR OFFICE CODE EXCEPTIONS FOR SPECIFIED AREA CODE TABLE RM-BF -55- PROGRAM 53 LCR SCHEDULE ASSIGNMENT NOTE: Enter time using 24-hour format: -56- TABLE RM-BG PROGRAM 54 LCR ROUTE DEFINITION -57- TABLE RM-BH PROGRAM 55-0 LCR MODIFIED DIGITS-DELETE TABLE RM-BI -58- PROGRAM 55-1 LCR MODIFIED DIGITS-ADD NOTE: Pause codes may also be entered. To enter pauses, press "P" plus the pause number (1 ~ 8). -59- TABLE RM-BJ PROGRAM 55-2 LCR MODIFIED DIGITS-END NOTE: Pause codes may also be entered. To enter pauses, press "P" plus the pause number (1 ~ 8). -60- TABLE RM-BK TABLE RM-BL PROGRAM 56 LCR STATION GROUP ASSIGNMENT PROGRAM DATA DUMP -61- TABLE RM-BM SPEED DIALING DATA DUMP TABLE RM-BN LCD MESSAGING DATA DUMP -62- TABLE RM-BO 1. To cancel a message set via Mode 95, use Mode 97 procedure. 3. DKT = digital telephone; EKT = electronic telephone. MODE 95 REMOTE CALLING STATION MESSAGING (ADD/REVIEW/CHANGE) TABLE RM-BP -63- 3. DKT = digital telephone; EKT = electronic telephone. MODE 97 REMOTE CALLING STATION MESSAGING (ADD/CHANGE) To store system message change permanently, DKT or EKT XXX must be station assigned to port 00. -64- TABLE RM-BQ 1. Press m at any time to start over. -65- TABLE RM-BR 1. [M] represents the message entered. 2. DKT = digital telephone; EKT = electronic telephone. MODE 96 REMOTE CALLED STATION MESSAGING (ADD/CHANGE) Enter m (lower case) anytime it is desired to start over in this procedure. IMPORTANT! TABLE RM-BT GENERAL STATION ACCESS AND BUTTON ACTIVATION NOTE: Button numbers begin at 01. -67- TABLE RM-BU CO LINE TEST NOTES: 1. 2. 3. Program 15-5 allows CO-to-CO connections. TABLE RM-BV -68- SYSTEM DATE/DAY/TIME SETTING PROCEDURE -69- TABLE RM-BW NOTE: If program entry is not correct, SPEED DIAL MODE (CHANGE/REVIEW) NOTE: If programming system speed dial, enter port number -70- REMOTE MAINTENANCE PROCEDURES INDEX -71- MESSAGE RECORD SHEETUse several sheets if necessary